Home › Suspension › REAR SUSPENSION › REAR AXLE BEAM (for Hatchback)

REAR AXLE BEAM (for Hatchback) > INSTALLATION

for Preparation Click here



1. TEMPORARILY TIGHTEN REAR AXLE BEAM ASSEMBLY


  1. Slowly jack up the rear axle beam assembly with an engine lifter using 2 wooden blocks and 2 attachments or equivalent tools and temporarily tighten the rear axle beam assembly to the body with the 2 B bolts.


    C261477E01


    Text in Illustration 
    *1
    Attachment
    *2
    Wooden Block
    *3
    Engine Lifter
    -
    -

    NOTICE:
    Make sure to secure the rear axle beam assembly to prevent it from dropping.

  1. Temporarily tighten the rear axle beam assembly to the rear shock absorber assemblies LH and RH with the 2 A bolts and 2 nuts.

    NOTICE:
    Since a jam nut is used, turn the bolt.



2. INSTALL REAR COIL SPRING LH
  1. Support the spring seat of the rear axle beam assembly using 2 jacks and 2 wooden blocks.

  1. Remove the 2 bolts while holding the 2 nuts and separate the rear axle beam assembly from the rear shock absorber assemblies LH and RH.

    NOTICE:
    Since a jam nut is used, turn the bolt.

  1. Slowly lower the rear axle beam assembly using 2 jacks and 2 wooden blocks.

  1. Install the rear lower coil spring insulator LH to the rear axle beam assembly.



    C110329E04
  1. Install the rear upper coil spring insulator LH so that its gap fits to the end of rear coil spring LH.
    Text in Illustration 
    *a
    Fit



    C233115
  1. Install the rear coil spring LH to the rear axle beam assembly.
    Text in Illustration 
    V100144
    Paint Mark

    NOTICE:
    The paint mark of the rear coil spring LH should be towards the underside and rear side of the vehicle.

  1. Slowly jack up the rear axle beam assembly using 2 jacks and 2 wooden blocks, and temporarily install the rear axle beam assembly with the 2 bolts and 2 nuts.

    NOTICE:
    Since a jam nut is used, turn the bolt.



3. INSTALL REAR COIL SPRING RH

HINT:
Use the same procedure for the RH side as for the LH side.



4. INSTALL REAR AXLE BEAM DYNAMIC DAMPER LH (w/ Dynamic Damper)
  1. Install the rear axle beam dynamic damper LH to the rear axle beam assembly with the bolt.

    Torque:
    50 N*m{ 510 kgf*cm , 37 ft.*lbf }



5. INSTALL REAR AXLE BEAM DYNAMIC DAMPER RH (w/ Dynamic Damper)

HINT:
Use the same procedure for the RH side as for the LH side.



6. INSTALL REAR AXLE HUB AND BEARING ASSEMBLY (for Rear Drum Brake)
  1. Install the axle hub and bearing onto the axle beam with the 4 bolts.

    Torque:
    90 N*m{ 918 kgf*cm , 66 ft.*lbf }



7. INSTALL REAR AXLE HUB AND BEARING ASSEMBLY (for Rear Disc Brake)
  1. Install the dust cover and the axle hub and bearing onto the axle beam with the 4 bolts.

    Torque:
    90 N*m{ 918 kgf*cm , 66 ft.*lbf }



8. INSPECT REAR AXLE HUB BEARING LOOSENESS (for Rear Drum Brake)


    C121815
  1. Using a dial indicator, check the backlash near the center of the axle hub.

    Maximum:
    0.05 mm (0.00197 in.)

    If the runout exceeds the maximum, replace the rear axle hub and bearing assembly.



9. INSPECT REAR AXLE HUB BEARING LOOSENESS (for Rear Disc Brake)


    C235846
  1. Using a dial indicator, check the backlash near the center of the axle hub.

    Maximum:
    0.05 mm (0.00197 in.)

    If the runout exceeds the maximum, replace the rear axle hub and bearing assembly.



10. INSPECT REAR AXLE HUB RUNOUT (for Rear Drum Brake)


    C121816
  1. Using a dial indicator, check the runout of the surface of the axle hub.

    Maximum:
    0.07 mm (0.00276 in.)

    If the runout exceeds the maximum, replace the rear axle hub and bearing assembly.



11. INSPECT REAR AXLE HUB RUNOUT (for Rear Disc Brake)


    C235847
  1. Using a dial indicator, check the runout of the surface of the axle hub.

    Maximum:
    0.07 mm (0.00276 in.)

    If the runout exceeds the maximum, replace the rear axle hub and bearing assembly.



12. INSTALL REAR BRAKE DRUM SUB-ASSEMBLY (for Rear Drum Brake)


13. INSTALL REAR DISC (for Rear Disc Brake)


    C236431E01
  1. Align the matchmarks of the rear disc and axle hub and install the rear disc.
    Text in Illustration 
    *a
    Matchmark

    NOTICE:
    When replacing the disc with a new one, select the installation position where the rear disc has minimal runout.



14. INSTALL REAR DISC BRAKE CYLINDER MOUNTING LH (for Rear Disc Brake)
  1. Install the rear disc brake cylinder mounting to the axle beam with the 2 bolts.

    Torque:
    57 N*m{ 585 kgf*cm , 42 ft.*lbf }



15. INSTALL REAR DISC BRAKE CYLINDER MOUNTING RH (for Rear Disc Brake)

HINT:
Use the same procedure for the RH side as for the LH side.



16. INSTALL REAR DISC BRAKE PAD (for Rear Disc Brake)
  1. Install the 2 rear disc brake pads to the rear disc brake cylinder mounting.

    NOTICE:
    There should be no oil or grease on the friction surfaces of the disc brake pads or the rear disc.



17. INSTALL REAR DISC BRAKE CYLINDER ASSEMBLY LH (for Rear Disc Brake)


C219089E01
  1. To compensate for pad wear when reusing the pad, use SST to push and turn the piston (LH side: counterclockwise, RH side: clockwise) to the position where the protrusion on the pad lines up properly with the piston groove.

    SST
    09719-12010   (09719-01030)

    HINT:
    Place the disc between the 2 brake pads and determine the piston return value.

  1. Hold the rear disc brake pad guide pin, and install the rear disc brake cylinder assembly to the rear disc brake cylinder mounting with the 2 bolts.

    Torque:
    34 N*m{ 350 kgf*cm , 25 ft.*lbf }



18. INSTALL REAR DISC BRAKE CYLINDER ASSEMBLY RH (for Rear Disc Brake)

HINT:
Use the same procedure for the RH side as for the LH side.



19. INSTALL NO. 3 PARKING BRAKE CABLE ASSEMBLY
  1. Install the No. 3 parking brake cable assembly with the bolt and a new clamp.

    Torque:
    6.0 N*m{ 61 kgf*cm , 53 in.*lbf }



20. INSTALL NO. 2 PARKING BRAKE CABLE ASSEMBLY

HINT:
Use the same procedure for the No. 3 parking brake cable assembly.



21. INSTALL NO. 4 REAR BRAKE TUBE (for Rear Drum Brake)
  1. Install the No. 4 rear brake tube onto the rear axle beam assembly with the nut.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. Install the rear flexible hose LH to the rear axle beam assembly with a new clip.

  1. Using a union nut wrench 10 mm, install the No. 4 rear brake tube while holding the rear flexible hose LH with a wrench.

    Torque:
    15 N*m{ 155 kgf*cm , 11 ft.*lbf }

    NOTICE:
    Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (Click here).



22. INSTALL NO. 3 REAR BRAKE TUBE (for Rear Drum Brake)

HINT:
Use the same procedure for the No. 4 rear brake tube.



23. INSTALL NO. 4 REAR BRAKE TUBE (for Rear Disc Brake)
  1. Install the No. 4 rear brake tube onto the rear axle beam assembly with the nut.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. Install the 2 rear flexible hoses LH to the rear axle beam assembly with 2 new clips.

  1. Using a union nut wrench 10 mm, install the No. 4 rear brake tube to the rear flexible hose LH while holding the rear flexible hose LH with a wrench.

    Torque:
    15 N*m{ 155 kgf*cm , 11 ft.*lbf }

    NOTICE:
    Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (Click here).



24. INSTALL NO. 3 REAR BRAKE TUBE (for Rear Disc Brake)

HINT:
Use the same procedure for the No. 4 rear brake tube.



25. INSTALL SKID CONTROL SENSOR WIRE LH (w/ ABS)
  1. Install the skid control sensor wire LH onto the rear axle beam assembly with the nut.

    Torque:
    6.0 N*m{ 61 kgf*cm , 53 in.*lbf }

  1. Connect the skid control sensor wire LH connector.



26. INSTALL SKID CONTROL SENSOR WIRE RH (w/ ABS)

HINT:
Use the same procedure for the RH side as for the LH side.



27. INSTALL REAR WHEEL

Torque:
103 N*m{ 1050 kgf*cm , 76 ft.*lbf }



28. STABILIZE SUSPENSION
  1. Lower the vehicle from the jack.

  1. Bounce the vehicle up and down several times to stabilize the suspension.



29. FULLY TIGHTEN REAR AXLE BEAM ASSEMBLY


    C204012E02
  1. Suspend the jack on the rear axle spring seat and adjust the length of the rear shock absorber assembly to the reference value.
    Text in Illustration 
    *a
    RH Side
    *b
    LH Side

    Length of shock absorber:
    220 mm (8.66 in.)

  1. Fully tighten the 2 bolts.

    Torque:
    90 N*m{ 918 kgf*cm , 66 ft.*lbf }



30. FULLY TIGHTEN REAR SHOCK ABSORBER ASSEMBLY LH
  1. Fully tighten the rear shock absorber assembly (lower side) with the bolt.

    Torque:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }



31. FULLY TIGHTEN REAR SHOCK ABSORBER ASSEMBLY RH

HINT:
Use the same procedure for the RH side as for the LH side.



32. BLEED BRAKE LINE
(Click here)


33. BLEED CLUTCH LINE (for Manual Transaxle)
(Click here)


34. INSPECT REAR WHEEL ALIGNMENT
(Click here)


35. CHECK SPEED SENSOR SIGNAL (w/ ABS)
(Click here)


36. CHECK SPEED SENSOR SIGNAL (w/ VSC)
(Click here)