DTC B1650/32 Occupant Classification System Malfunction |
| DTC No. | DTC Detecting Conditions | Trouble Areas |
| B1650/32 |
|
|

| 1.CHECK DTC (CENTER AIRBAG SENSOR ASSEMBLY) |
![]() |
Turn the ignition switch to the on position, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch to the lock position.
Turn the ignition switch to the on position, and wait for at least 60 seconds.
Check for DTCs (Click here).
|
| ||||
| NG | |
| 2.CHECK DTC (OCCUPANT CLASSIFICATION ECU) |
Turn the ignition switch to the on position, and wait for at least 10 seconds.
Using the Techstream, check for DTCs of the occupant classification ECU (Click here).
|
| ||||
| OK | |
| 3.CHECK CONNECTION OF CONNECTORS |
Turn the ignition switch to the lock position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Check that the connectors are properly connected to the center airbag sensor assembly and the occupant classification ECU.
|
| ||||
| OK | |
| 4.CHECK FLOOR WIRE (FOR OPEN) |
![]() |
Disconnect the connectors from the center airbag sensor assembly and the occupant classification ECU.
Using a service wire, connect J24-8 (FSR+) and J24-4 (FSR-) of connector C.
Measure the resistance.
| Tester Connection | Condition | Specified Condition |
| J9-12 (FSP+) - J9-13 (FSP-) | Always | Below 1 Ω |
|
| ||||
| OK | |
| 5.CHECK FLOOR WIRE (FOR SHORT) |
![]() |
Disconnect the service wire from connector C.
Measure the resistance.
| Tester Connection | Condition | Specified Condition |
| J9-12 (FSP+) - J9-13 (FSP-) | Always | 1 MΩ or Higher |
|
| ||||
| OK | |
| 6.CHECK FLOOR WIRE (TO B+) |
![]() |
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the on position.
Measure the voltage.
| Tester Connection | Switch Condition | Specified Condition |
| J9-12 (FSP+) - Body ground | Ignition switch ON | Below 1 V |
| J9-13 (FSP-) - Body ground | Ignition switch ON | Below 1 V |
|
| ||||
| OK | |
| 7.CHECK FLOOR WIRE (TO GROUND) |
![]() |
Turn the ignition switch to the lock position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Measure the resistance.
| Tester Connection | Condition | Specified Condition |
| J9-12 (FSP+) - Body ground | Always | 1 MΩ or Higher |
| J9-13 (FSP-) - Body ground | Always | 1 MΩ or Higher |
|
| ||||
| OK | |
| 8.CHECK CENTER AIRBAG SENSOR ASSEMBLY |
![]() |
Turn the ignition switch to the lock position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Replace the center airbag sensor assembly (Click here).
Connect the connectors to the center airbag sensor assembly.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the on position, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch to the lock position.
Turn the ignition switch to the on position, and wait for at least 60 seconds.
Check for DTCs (Click here).
|
| ||||
| NG | |
| 9.REPLACE OCCUPANT CLASSIFICATION ECU |
Turn the ignition switch to the lock position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Replace the occupant classification ECU (Click here).
| NEXT | |
| 10.PERFORM ZERO POINT CALIBRATION |
Connect the negative (-) terminal cable to the battery.
Connect the Techstream to the DLC3.
Turn the ignition switch to the on position.
Using the Techstream, perform the zero point calibration (Click here).
| NEXT | |
| 11.PERFORM SENSITIVITY CHECK |
Using the Techstream, perform the sensitivity check (Click here).
Confirm that nothing is placed on the passenger seat.
Confirm that the first sensor reading is within the standard range.
Place a 30 kg (66.14 lb) weight (e.g. a lead mass) onto the front passenger seat.
Confirm that the sensitivity is within the standard range.
| NEXT | ||
| ||