SFI SYSTEM (for Sedan) > Fuel Pump Control Circuit |


| 1.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE FUEL PUMP/SPEED) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump/Speed.
Check whether the fuel pump operating sound occurs when perform the Active Test on the Techstream.
| Result | Proceed to |
| NG | A |
| OK | B |
|
| ||||
| A | |
| 2.INSPECT MAIN BODY ECU (C/OPN RELAY INPUT VOLTAGE) |
![]() |
Measure the voltage between the terminal of the main body ECU and the body ground when the ignition switch is turned to ON and OFF.
| Tester Connections | Switch Conditions | Specified Conditions |
| 4B-11 - Body ground | Ignition switch off | Below 1 V |
| 4F-4 - Body ground | ||
| 4B-11 - Body ground | Ignition switch ON | 11 to 14 V |
| 4F-4 - Body ground |
| Result | Proceed to |
| NG | A |
| OK | B |
|
| ||||
| A | |
| 3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - INTEGRATION RELAY) |
![]() |
Remove the integration relay from the engine room relay block.
Disconnect the main body ECU connector.
Check the resistance.
| Tester Connections | Specified Conditions |
| 1B-4 - 4F-4 | Below 1 Ω |
| 1A-4 - 4B-11 |
| Tester Connections | Specified Conditions |
| 4F-4 - Body ground | 10 kΩ or higher |
| 4B-11 - Body ground |
Reinstall the integration relay.
Reconnect the main body ECU connector.
|
| ||||
| OK | ||
| ||
| 4.INSPECT MAIN BODY ECU (C/OPN RELAY) |
![]() |
Remove the main body ECU.
Check the C/OPN relay resistance.
| Tester Connections | Specified Conditions |
| 4B-11 - 4A-8 | 10 kΩ or higher |
| Below 1 Ω (when battery voltage is applied to terminals 4F-4 and 4E-5) |
Reinstall the main body ECU.
|
| ||||
| OK | |
| 5.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - ECM) |
![]() |
Disconnect the A21 ECM connector.
Disconnect the 4E connector from main body ECU.
Check the resistance.
| Tester Connections | Specified Conditions |
| Main Body ECU (4E-5) - FC (A21-7) | Below 1 Ω |
| Tester Connections | Specified Conditions |
| Main body ECU (4E-5) or FC (A21-7) - Body ground | 10 kΩ or higher |
Reconnect the main body ECU and the ECM connectors.
|
| ||||
| OK | |
| 6.CHECK HARNESS AND CONNECTOR (C/OPN RELAY - FUEL PUMP - BODY GROUND) |
![]() |
Check the harness and the connectors between the main body ECU and the fuel pump.
Disconnect the 4A main body ECU connector.
Disconnect the J5 fuel pump connector.
Check the resistance.
| Tester Connections | Specified Conditions |
| Main body ECU (4A-8) - Fuel pump (J5-4) | Below 1 Ω |
| Tester Connections | Specified Conditions |
| Main body ECU (4A-8) or Fuel pump (J5-4) - Body ground | 10 kΩ or higher |
Check the harness and the connectors between the fuel pump and the body ground.
Disconnect the J5 fuel pump connector.
Check the resistance.
| Tester Connections | Specified Conditions |
| Fuel pump (J5-5) - Body ground | Below 1 Ω |
Reconnect the main body ECU connector.
Reconnect the fuel pump connector.
|
| ||||
| OK | |
| 7.INSPECT FUEL PUMP |
![]() |
Inspect fuel pump resistance.
Measure the resistance between the terminals.
Inspect fuel pump operation.
Apply the battery voltage to both the terminals. Check that the pump operates.
|
| ||||
| OK | ||
| ||
| 8.READ VALUE USING TECHSTREAM (STARTER SIGNAL) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.
Check the result when the ignition switch is turned to ON and START.
| Ignition Switch Position | Starter Signal |
| ON | OFF |
| START | ON |
|
| ||||
| OK | |
| 9.READ VALUE USING TECHSTREAM (ENGINE SPEED) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Engine Speed.
Read the values displayed on the Techstream while cranking.
|
| ||||
| OK | ||
| ||