CAN COMMUNICATION SYSTEM (for Hatchback) > Open in One Side of CAN Branch Line |
| Symptom | Trouble Area |
| 2 or more ECUs and/or sensors do not appear on the Techstream "CAN Bus Check" screen. |
|


| 1.CHECK OPEN IN ONE SIDE OF CAN BRANCH WIRE (SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY)) |
Disconnect the A70*1 or A71*2 skid control ECU (brake actuator assembly) connector.
*1: w/ VSC
*2: w/o VSC
Select "Communication Bus Check" on the Techstream (Click here).
| Result | Proceed to |
| "Skid Control (ABS/VSC/TRAC)" not displayed on Techstream. | A |
| Several ECUs and sensors other than "Skid Control (ABS/VSC/TRAC)" not displayed on Techstream. | B |
|
| ||||
| A | |
| 2.CHECK OPEN IN ONE SIDE OF CAN BRANCH WIRE (SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) BRANCH WIRE) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| A70-25 (CANH) - A70-14 (CANL)*1 A71-25 (CANH) - A71-14 (CANL)*2 | Ignition switch off | 54 to 69 Ω |
| *A | w/ VSC |
| *B | w/o VSC |
| *a | Front view of wire harness connector (to Skid Control ECU (Brake Actuator Assembly)) |
| Result | Proceed to |
| NG | A |
| OK (w/ VSC) | B |
| OK (w/o VSC) | C |
Reconnect the A70*1 or A71*2 skid control ECU (brake actuator assembly) connector.
|
| ||||
|
| ||||
| A | ||
| ||
| 3.CHECK OPEN IN ONE SIDE OF CAN BRANCH WIRE (AIR CONDITIONING AMPLIFIER ASSEMBLY) |
Disconnect the D130 air conditioning amplifier assembly connector.
Select "Communication Bus Check" on the Techstream (Click here).
| Result | Proceed to |
| "Air Conditioning Amplifier" not displayed on Techstream. | A |
| Several ECUs and sensors other than "Air Conditioning Amplifier" not displayed on Techstream. | B |
|
| ||||
| A | |
| 4.CHECK OPEN IN ONE SIDE OF CAN BRANCH WIRE (AIR CONDITIONING AMPLIFIER ASSEMBLY BRANCH WIRE) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| D130-8 (TX+) - D130-9 (TX-) | Ignition switch off | 54 to 69 Ω |
| *a | Front view of wire harness connector (to Air Conditioning Amplifier Assembly) |
Reconnect the D130 air conditioning amplifier assembly connector.
|
| ||||
| OK | ||
| ||
| 5.CHECK OPEN IN ONE SIDE OF CAN BRANCH WIRE (AIRBAG SENSOR ASSEMBLY) |
Disconnect the D112 airbag sensor assembly connector.
Select "Communication Bus Check" on the Techstream (Click here).
| Result | Proceed to |
| "Airbag" not displayed on Techstream. | A |
| Several ECUs and sensors other than "Airbag" not displayed on Techstream. | B |
|
| ||||
| A | |
| 6.CHECK OPEN IN ONE SIDE OF CAN BRANCH WIRE (AIRBAG SENSOR ASSEMBLY BRANCH WIRE) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| D112-13 (CANH) - D112-22 (CANL) | Ignition switch off | 54 to 69 Ω |
| *a | Front view of wire harness connector (to Airbag sensor Assembly) |
Reconnect the D112 airbag sensor assembly connector.
|
| ||||
| OK | ||
| ||
| 7.CHECK OPEN IN ONE SIDE OF CAN BRANCH WIRE (STEERING ANGLE SENSOR (SPIRAL CABLE SUB-ASSEMBLY)) |
Disconnect the D122 steering angle sensor (spiral cable sub-assembly) connector.
Select "Communication Bus Check" on the Techstream (Click here).
| Result | Proceed to |
| "Spiral cable (Steering Angle Sensor)" not displayed on Techstream. | A |
| Several ECUs and sensors other than "Spiral cable (Steering Angle Sensor)" not displayed on Techstream. | B |
|
| ||||
| A | |
| 8.CHECK OPEN IN ONE SIDE OF CAN BRANCH WIRE (STEERING ANGLE SENSOR (SPIRAL CABLE SUB-ASSEMBLY) BRANCH WIRE) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| D122-4 (CANH) - D122-3 (CANL) | Ignition switch off | 54 to 69 Ω |
| *a | Front view of wire harness connector (to Steering Angle Sensor (Spiral Cable Sub-assembly)) |
Reconnect the D122 steering angle sensor (spiral cable sub-assembly) connector.
|
| ||||
| OK | ||
| ||
| 9.CHECK OPEN IN ONE SIDE OF CAN BRANCH WIRE (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)) |
Disconnect the D143 main body ECU (multiplex network body ECU) connector.
Select "Communication Bus Check" on the Techstream (Click here).
| Result | Proceed to |
| "Main Body" not displayed on Techstream. | A |
| Several ECUs and sensors other than "Main Body" not displayed on Techstream. | B |
|
| ||||
| A | |
| 10.CHECK OPEN IN ONE SIDE OF CAN BRANCH WIRE (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) BRANCH WIRE) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| D143-14 (CANH) - D143-13 (CANL) | Ignition switch off | 54 to 69 Ω |
| *a | Front view of wire harness connector (to Main Body ECU (Multiplex Network Body ECU)) |
Reconnect the D143 main body ECU (multiplex network body ECU) connector.
|
| ||||
| OK | ||
| ||
| 11.CHECK OPEN IN ONE SIDE OF CAN BRANCH WIRE (POWER STEERING ECU ASSEMBLY BRANCH WIRE) |
Disconnect the D104 power steering ECU assembly connector.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| D104-7 (CANH) - D104-8 (CANL) | Ignition switch off | 54 to 69 Ω |
| *a | Rear view of wire harness connector (to Power Steering ECU Assembly) |
Reconnect the D104 power steering ECU assembly connector.
|
| ||||
| OK | ||
| ||