FUEL LID LOCK CONTROL CABLE ASSEMBLY (for Hatchback 3 Door) > INSTALLATION |
| 1. INSTALL FUEL FILLER OPENING LID LOCK RETAINER |
![]() |
Align the 2 claws B of the fuel filler opening lid lock retainer with the 2 slits.
Push in and install the fuel filler opening lid lock retainer while securely engaging the 2 claws A.
| *1 | Claw A |
| *2 | Claw B |
| *a | Slit |
| 2. INSTALL FUEL LID LOCK CONTROL CABLE SUB-ASSEMBLY |
Engage the 4 clamps and install the fuel lid lock control cable sub-assembly as shown in the illustration.

| *1 | Fuel Lid Lock Control Cable Sub-assembly | *2 | Wire Harness Clamp |
![]() |
Engage the 2 claws and install the fuel lid lock control cable sub-assembly.
| 3. INSTALL FUEL LID LOCK OPEN LEVER SUB-ASSEMBLY |
Connect the fuel lid lock control cable sub-assembly.
![]() |
Engage the guide.
Install the fuel lid lock open lever sub-assembly with the bolt.
| 4. INSTALL FRONT FLOOR CARPET ASSEMBLY |
Engage the 6 clamps.
Install the front floor carpet assembly with the clip.
| 5. INSTALL NO. 2 FLOOR CARPET HOOK |
![]() |
Insert the hook of the No. 2 floor carpet hook and rotate it 90° in the direction shown by the arrow in the illustration to engage the hook, and install the No. 2 floor carpet hook.
| 6. INSTALL JACK ASSEMBLY |
| 7. INSTALL JACK COVER |
| 8. INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH |
| 9. INSTALL NO. 2 ROOM LIGHT ASSEMBLY |
![]() |
Connect the connector.
Engage the claw to install the No. 2 room light assembly.
| 10. INSTALL REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY RH |
Engage the 2 claws and install the rear seat 3 point type outer belt.
Tighten the bolt.
| 11. INSTALL REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY LH |
| 12. INSTALL REAR FLOOR FINISH PLATE |
Engage the 4 guides and the 4 claws to install the rear floor finish plate.
| 13. INSTALL FRONT QUARTER TRIM PANEL ASSEMBLY RH |
Engage the 8 clips and the 10 claws.
Engage the 3 guides and install the quarter trim panel.
| 14. INSTALL FRONT QUARTER TRIM PANEL ASSEMBLY LH |
| 15. INSTALL FRONT SEAT OUTER BELT ASSEMBLY RH |
Install the floor end of the front seat outer belt with the bolt.
Engage the 2 claws and install the anchor cover.
| 16. INSTALL FRONT SEAT OUTER BELT ASSEMBLY LH |
| 17. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH |
Install the front door opening trim.
| 18. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH |
Install the front door opening trim.
| 19. INSTALL COWL SIDE TRIM BOARD RH |
Engage the clip.
Install the cowl side trim board with clip.
| 20. INSTALL COWL SIDE TRIM BOARD LH |
| 21. INSTALL FRONT DOOR SCUFF PLATE RH |
Engage the 8 claws and install the front door scuff plate.
| 22. INSTALL FRONT DOOR SCUFF PLATE LH |
| 23. INSTALL REAR CONSOLE BOX |
| 24. INSTALL REAR SEAT ASSEMBLY (for 60/40 Split Seat Type LH Side) |
| 25. INSTALL REAR SEAT ASSEMBLY (for 60/40 Split Seat Type RH Side) |
| 26. INSTALL REAR SEAT ASSEMBLY (for Fold Down Seat Type) |
| 27. INSTALL FRONT SEAT ASSEMBLY (for Driver Side) |
| 28. INSTALL FRONT SEAT ASSEMBLY (for Front Passenger Side) |
| 29. INSTALL DECK BOARD ASSEMBLY |
Install the deck board.