Home › Engine / Hybrid System › 1NZ-FE ENGINE CONTROL › SFI SYSTEM (for Hatchback)

SFI SYSTEM (for Hatchback) > Starter Signal Circuit


DESCRIPTION

  1. While the engine is being cranked, current flows from terminal ST2 of the ignition or starter switch assembly to the park/neutral position switch and also flows to terminal STA of the ECM (STA Signal).

WIRING DIAGRAM

Refer to DTC P0617 .

INSPECTION PROCEDURE

NOTICE:
  1. Inspect the fuses for circuits related to this system before performing the following inspection procedure.
  2. After turning ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click here).

1.CHECK WHETHER ENGINE CAN BE CRANKED
  1. Check if engine can be cranked.
    Result 
    Result
    Proceed to
    Engine cannot be cranked
    A
    Engine can be cranked
    B



B
Go to step 13
A


2.READ VALUE USING TECHSTREAM (STARTER SIGNAL)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.

  1. Check the result when the ignition switch is turned ON and the engine starts.

OK:
Ignition Switch Position
Techstream Display
(Starter Signal)
ON
OFF
START
ON

Result 
Result
Proceed to
Outside standard range
(for manual transaxle)
A
Outside standard range
(for automatic transaxle)
B
Within standard range
(for manual transaxle)
C
Within standard range
(for automatic transaxle)
D


B
Go to step 7

C
Go to step 6

D
Go to step 10
A


3.INSPECT CLUTCH START SWITCH ASSEMBLY
  1. Inspect the clutch start switch assembly .



NG
REPLACE CLUTCH START SWITCH ASSEMBLY (Click here)
OK


4.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY
  1. Inspect the ignition or starter switch assembly (Click here).



NG
REPLACE IGNITION OR STARTER SWITCH ASSEMBLY (Click here)
OK


5.CHECK HARNESS AND CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY - CLUTCH START SWITCH ASSEMBLY)
  1. Disconnect the ignition or starter switch assembly connector.

  1. Disconnect the clutch start switch assembly connector.

  1. Measure the resistance according to the value(s) in the table below.


Standard Resistance:

Tester Connection
Condition
Specified Condition
D109-7 (ST2) - A66-2
Always
Below 1 Ω
D109-7 (ST2) - C51-63 (NSW)
Always
Below 1 Ω
D109-7 (ST2) or A66-2 - Body ground
Always
10 kΩ or higher
D109-7 (ST2) or C51-63 (NSW) - Body ground
Always
10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.CHECK HARNESS AND CONNECTOR (CLUTCH START SWITCH ASSEMBLY -ECM - ST RELAY)
  1. Remove the ST relay from the engine room relay block.

  1. Disconnect the ECM connector.

  1. Disconnect the clutch start switch assembly connector.

  1. Measure the resistance according to the value(s) in the table below.


Standard Resistance:

Tester Connection
Condition
Specified Condition
2 (ST relay holder) - A72-22 (STA)
Always
Below 1 Ω
2 (ST relay holder) - A66-1
Always
Below 1 Ω
A72-22 (STA) or A66-1 - Body ground
Always
10 kΩ or higher

Result 
Result
Proceed to
Outside standard range
A
Normal standard range
B


B
Go to step 11
A

REPAIR OR REPLACE HARNESS OR CONNECTOR 

7.INSPECT PARK/NEUTRAL POSITION SWITCH
  1. Inspect the park/neutral position switch (Click here).



NG
REPLACE PARK/NEUTRAL POSITION SWITCH (Click here)
OK


8.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY
  1. Inspect the ignition or starter switch assembly (Click here).



NG
REPLACE IGNITION OR STARTER SWITCH ASSEMBLY (Click here)
OK


9.CHECK HARNESS AND CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY - PARK/NEUTRAL POSITION SWITCH)
  1. Disconnect the ignition or starter switch assembly connector.

  1. Disconnect the park/neutral position switch connector.

  1. Measure the resistance according to the value(s) in the table below.


Standard Resistance:

Tester Connection
Condition
Specified Condition
D109-7 (ST2) - C67-4
Always
Below 1 Ω
D109-7 (ST2) - C51-63 (NSW)
Always
Below 1 Ω
D109-7 (ST2) or C67-4 - Body ground
Always
10 kΩ or higher
D109-7 (ST2) or C51-63 (NSW) - Body ground
Always
10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


10.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM - ST RELAY)
  1. Remove the ST relay from the engine room relay block.

  1. Disconnect the ECM connector.

  1. Disconnect the park/neutral position switch connector.

  1. Measure the resistance according to the value(s) in the table below.


Standard Resistance:

Tester Connection
Condition
Specified Condition
2 (ST relay holder) - A72-22 (STA)
Always
Below 1 Ω
2 (ST relay holder) - C67-5
Always
Below 1 Ω
A72-22 (STA) or C67-5 - Body ground
Always
10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


11.INSPECT BATTERY
  1. Check that the battery is not depleted.

OK:
Battery is not depleted.



NG
REPLACE BATTERY
OK


12.CHECK BATTERY TERMINAL
  1. Check that the battery terminals are not loose or corroded.

    OK:
    Battery terminals are not loose or corroded.



NG
REPAIR OR REPLACE BATTERY TERMINAL
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

13.READ VALUE USING TECHSTREAM (STARTER SIGNAL)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.

  1. Check the result when the ignition switch is turned ON and the engine starts.

    OK:
    Ignition Switch Position
    Techstream Display
    (Starter Signal)
    ON
    OFF
    START
    ON



NG
Go to step 14
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

14.CHECK HARNESS AND CONNECTOR (ECM - ST RELAY)
  1. Remove the ST relay from the engine room relay block.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    A72-22 (STA) - 2 (ST relay holder)
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)