Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM (for Hatchback)

AIR CONDITIONING SYSTEM (for Hatchback) > Recirculation Damper Servo Motor Circuit


DESCRIPTION

The No. 1 blower damper servo sub-assembly (air inlet servo motor) and No. 1 heater control sub-assembly (FRESH/RECIRC switch, MODE switch) are powered through the A/C fuse. Operating the No. 1 heater control sub-assembly (FRESH/RECIRC switch, MODE switch) drives the No. 1 blower damper servo sub-assembly (air inlet servo motor) to switch between "FRESH" and "RECIRCULATION".

WIRING DIAGRAM


E231015E01


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedures.

1.INSPECT NO. 1 BLOWER DAMPER SERVO SUB-ASSEMBLY (AIR INLET SERVO MOTOR)
  1. Inspect the No. 1 blower damper servo sub-assembly (air inlet servo motor) (Click here).



NG
REPLACE NO. 1 BLOWER DAMPER SERVO SUB-ASSEMBLY (AIR INLET SERVO MOTOR) (Click here)
OK


2.INSPECT NO. 1 HEATER CONTROL SUB-ASSEMBLY (FRESH/RECIRC SWITCH, MODE SWITCH)
  1. Inspect the No. 1 heater control sub-assembly (FRESH/RECIRC switch, MODE switch) (Click here).



NG
REPLACE NO. 1 HEATER CONTROL SUB-ASSEMBLY (FRESH/RECIRC SWITCH, MODE SWITCH) (Click here)
OK


3.CHECK HARNESS AND CONNECTOR (BLOWER DAMPER SERVO SUB-ASSEMBLY - IG1 NO. 1 RELAY)


    E229326E01
  1. Disconnect the D126 No. 1 blower damper servo sub-assembly (air inlet servo motor) connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    D126-5 (IG+) - Body ground
    Ignition switch off
    Below 1 V
    D126-5 (IG+) - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to No. 1 Blower Damper Servo Sub-Assembly (Air Inlet Servo Motor))



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK HARNESS AND CONNECTOR (NO. 1 HEATER CONTROL SUB-ASSEMBLY - IG1 NO. 1 RELAY)


    E214704E03
  1. Disconnect the D128 No. 1 heater control sub-assembly (FRESH/RECIRC switch, MODE switch) connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    D128-2 (A/C+) - Body ground
    Ignition switch off
    Below 1 V
    D128-2 (A/C+) - Body ground
    Ignition switch ON
    11 to 14 V
    D128-8 (ACID) - Body ground*1
    Ignition switch off
    Below 1 V
    D128-8 (ACID) - Body ground*1
    Ignition switch ON
    11 to 14 V

    *1: w/ Cooler
    Text in Illustration 
    *A
    w/ Cooler
    *a
    Front view of wire harness connector
    (to No. 1 Heater Control Sub-Assembly (FRESH/RECIRC Switch, MODE Switch))



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.CHECK HARNESS AND CONNECTOR (NO. 1 HEATER CONTROL SUB-ASSEMBLY - BODY GROUND)


    E214704E04
  1. Disconnect the D128 No. 1 heater control sub-assembly (FRESH/RECIRC switch, MODE switch) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D128-4 (REC) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to No. 1 Heater Control Sub-Assembly (FRESH/RECIRC Switch, MODE Switch))



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.CHECK HARNESS AND CONNECTOR (NO. 1 HEATER CONTROL SUB-ASSEMBLY - BLOWER DAMPER SERVO SUB-ASSEMBLY)
  1. Disconnect the D128 No. 1 heater control sub-assembly (FRESH/RECIRC switch, MODE switch) connector.

  1. Disconnect the D126 No. 1 blower damper servo sub-assembly (air inlet servo motor) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D128-3 (FRS) - D126-2 (FRS)
    Always
    Below 1 Ω
    D128-5 (LED+) - D126-1 (REC)
    Always
    Below 1 Ω
    D128-3 (FRS) - Body ground
    Always
    10 kΩ or higher
    D128-5 (LED+) - Body ground
    Always
    10 kΩ or higher

    Result 
    Result
    Proceed to
    NG
    A
    OK (w/ cooler)
    B
    OK (w/o cooler)
    C



B
Go to step 7

C
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)
A

REPAIR OR REPLACE HARNESS OR CONNECTOR 

7.CHECK HARNESS AND CONNECTOR (NO. 1 HEATER CONTROL SUB-ASSEMBLY - AIR CONDITIONING AMPLIFIER ASSEMBLY)
  1. Disconnect the D128 No. 1 heater control sub-assembly (FRESH/RECIRC switch, MODE switch) connector.

  1. Disconnect the D130 air conditioning amplifier assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D128-1 (F/D) - D130-2 (A/C)
    Always
    Below 1 Ω
    D128-1 (F/D) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)