DTC C1277 Abnormal Change in Output Signal of Rear Speed Sensor RH (Test Mode DTC) |
DTC C1278 Abnormal Change in Output Signal of Rear Speed Sensor LH (Test Mode DTC) |
DTC C1415 Rear Speed Sensor RH Output Malfunction |
DTC C1416 Rear Speed Sensor LH Output Malfunction |
| DTC No. | DTC Detection Condition | Trouble Area |
| C1415 C1416 | Any of the following is detected:
|
|
| DTC No. | DTC Detection Condition | Trouble Area |
| C1277 C1278 | Detected only during Test Mode. |
|
| 1.CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION) |
Using the Techstream, check for any momentary interruption in the wire harness and connector corresponding to the DTC (Click here).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| RR Speed Open | RR speed sensor open detection / Normal or Error | Normal: Normal Error: Momentary interruption | - |
| RL Speed Open | RL speed sensor open detection / Error or Normal or Error | Normal: Normal Error: Momentary interruption | - |
|
| ||||
| OK | |
| 2.READ VALUE USING TECHSTREAM (REAR SPEED SENSOR) |
Connect the Techstream to the DLC3.
Start the engine.
Enter the following menus: Chassis / ABS/VSC/TRAC / Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| RR Wheel Speed | RR wheel speed sensor reading / min.: 0 km/h (0 mph), max.: 326 km/h (202 mph) | Vehicle stopped: 0 km/h | When driving at constant speed: No large fluctuations |
| RL Wheel Speed | RL wheel speed sensor reading / min.: 0 km/h (0 mph), max.: 326 km/h (202 mph) | Vehicle stopped: 0 km/h | When driving at constant speed: No large fluctuations |
Check that there is no difference between the speed value output from the speed sensor displayed on the Techstream and the speed value displayed on the speedometer when driving the vehicle.
|
| ||||
| OK | |
| 3.PERFORM TEST MODE (SIGNAL CHECK) |
Turn the ignition switch off.
Perform the sensor check in the Test Mode procedure (Click here).
|
| ||||
| OK | |
| 4.RECONFIRM DTC |
Turn the ignition switch off.
Clear the DTCs (Click here).
Start the engine.
Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.
Check if the same DTC is recorded (Click here).
| Result | Proceed to |
| DTCs C1415 and C1416 are not output | A |
| DTCs C1415 and/or C1416 are output | B |
|
| ||||
| A | ||
| ||
| 5.CHECK REAR SPEED SENSOR INSTALLATION |
Turn the ignition switch off.
![]() |
Check the speed sensor installation.
| *a | Normal |
| *b | Abnormal |
| *c | Clearance |
|
| ||||
| OK | |
| 6.CHECK HARNESS AND CONNECTOR (REAR SPEED SENSOR WIRE) |
Turn the ignition switch off.
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
Disconnect the skid control sensor wire connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| a10-2(+) - aJ3-1 | Always | Below 1 Ω |
| a10-1(-) - aJ3-2 | Always | Below 1 Ω |
| a10-2(+) - aJ3-2 | Always | 10 kΩ or higher |
| a10-2(+) - Body ground | Always | 10 kΩ or higher |
| a10-1(-) - aJ3-1 | Always | 10 kΩ or higher |
| a10-1(-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| d10-2(+) - dJ2-1 | Always | Below 1 Ω |
| d10-1(-) - dJ2-2 | Always | Below 1 Ω |
| d10-2(+) - dJ2-2 | Always | 10 kΩ or higher |
| d10-2(+) - Body ground | Always | 10 kΩ or higher |
| d10-1(-) - dJ2-1 | Always | 10 kΩ or higher |
| d10-1(-) - Body ground | Always | 10 kΩ or higher |
Reconnect the skid control sensor wire connector.
|
| ||||
| OK | |
| 7.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - REAR SPEED SENSOR) |
Turn the ignition switch off.
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
Disconnect the skid control ECU connector and the rear speed sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A71-17 (RR+) - a10-2 (+) | Always | Below 1 Ω |
| A71-16 (RR-) - a10-1 (-) | Always | Below 1 Ω |
| A71-5 (RL+) - d10-2 (+) | Always | Below 1 Ω |
| A71-4 (RL-) - d10-1 (-) | Always | Below 1 Ω |
| A71-17 (RR+) - Body ground | Always | 10 kΩ or higher |
| A71-16 (RR-) - Body ground | Always | 10 kΩ or higher |
| A71-5 (RL+) - Body ground | Always | 10 kΩ or higher |
| A71-4 (RL-) - Body ground | Always | 10 kΩ or higher |
Reconnect the skid control ECU connector.
|
| ||||
| OK | |
| 8.INSPECT SKID CONTROL ECU (SENSOR INPUT) |
![]() |
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| a10-2 (+) - Body ground | Ignition switch ON | 8 to 14 V |
| d10-2 (+) - Body ground | Ignition switch ON | 8 to 14 V |
| *a | Front view of wire harness connector (to Rear Speed Sensor) |
Reconnect the rear speed sensor connector.
|
| ||||
| OK | |
| 9.RECONFIRM DTC |
Turn the ignition switch off.
Clear the DTCs (Click here).
Start the engine.
Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.
Check if the same DTC is recorded (Click here).
| Result | Proceed to |
| DTCs C1415 and/or C1416 are output | A |
| DTCs C1415 and C1416 are not output | B |
|
| ||||
| A | |
| 10.REPLACE REAR AXLE HUB AND BEARING ASSEMBLY (REAR SPEED SENSOR, SENSOR ROTOR) |
Turn the ignition switch off.
Replace the rear speed sensor and rear axle hub and bearing assembly (Click here).
| NEXT | |
| 11.RECONFIRM DTC |
Turn the ignition switch off.
Clear the DTCs (Click here).
Start the engine.
Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.
Check if the same DTC is recorded (Click here).
| Result | Proceed to |
| DTCs C1415 and C1416 are not output | A |
| DTCs C1415 and/or C1416 are output | B |
|
| ||||
| A | ||
| ||