Home › Vehicle Exterior › DOOR / HATCH › FRONT DOOR › 2013.08–2013.12
RM30M0E _59 Vehicle Exterior _017122 DOOR / HATCH _0087456 FRONT DOOR A

DOOR / HATCH  FRONT DOOR  DISASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for both the LH and RH sides.

·

The procedure described below is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Hide 67492A 3.REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH

a.
B346702

Disengage the 2 clips and remove the front door lower frame bracket garnish.


Hide 69260 4.REMOVE FRONT DOOR WINDOW REGULATOR HANDLE ASSEMBLY (w/o Power Window)

a.
B347102C01
2.333,1.333 2.073,1.156 false 2.375,1.323 2.688,1.521 0.313,0.198 10 false *a
*a Protective Tape


Insert a clip remover with its shaft wrapped in protective tape between the window regulator handle plate and the front door window regulator handle assembly.


b.

Turn the front door window regulator handle assembly with the clip remover inserted, as shown in the illustration.


c.

Remove the shaft snap ring and the front door window regulator handle assembly.


d.
B346737

Remove the window regulator handle plate.


Hide 74232 5.REMOVE FRONT ARMREST BASE UPPER PANEL (w/o Power Window)

a.
B351252

Using a moulding remover, disengage the 7 claws and remove the front armrest base upper panel.


Hide 74232 6.REMOVE FRONT ARMREST BASE UPPER PANEL (w/ Power Window)

a.
B351253

Using a moulding remover, disengage the 9 claws.


b.
B346704

Disconnect the connector and remove the front armrest base upper panel.


Hide 67602 7.REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY

a.
B346705C01
1.135,0.792 1.302,0.688 true 1.344,0.563 1.656,0.76 0.313,0.198 10 false *a
*a Protective Tape


Using a screwdriver with its tip wrapped in protective tape, disengage the claw and open the door inside handle bezel plug.


b.
B346706

Remove the 3 screws.


c.
B346707

Disengage the 8 clips.


d.

Disengage the guide and the 5 claws.


e.
B356958C01
1.24,0.604 1.156,0.354 false 1.01,1.083 1.167,0.875 true 0.99,0.229 1.302,0.427 0.313,0.198 10 false *1 0.875,1.115 1.188,1.313 0.313,0.198 10 false *2
*1 Front Door Inside Locking Cable Assembly
*2 Front Door Lock Remote Control Cable Assembly


Disengage the 2 guides, disconnect the front door lock remote control cable assembly and front door inside locking cable assembly and remove the front door trim board sub-assembly.


Hide 69206B 8.REMOVE FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY

a.
B346709

Disengage the 4 guides and remove the front door inside handle sub-assembly from the front door trim board sub-assembly.


Hide 86160 9.REMOVE FRONT NO. 1 SPEAKER ASSEMBLY

Hide 87940 10.REMOVE OUTER REAR VIEW MIRROR ASSEMBLY (w/ Power Mirror Adjust Function)

Hide 87940 11.REMOVE OUTER REAR VIEW MIRROR ASSEMBLY (w/o Power Mirror Adjust Function)

Hide 68210C 12.REMOVE FRONT DOOR GLASS OUTER WEATHERSTRIP ASSEMBLY

Hide 75756C 13.REMOVE FRONT DOOR WINDOW FRAME REAR MOULDING

Hide 75922M 14.REMOVE NO. 1 BLACK OUT TAPE (w/ Black Out Tape)

Hide 68172A 15.REMOVE FRONT DOOR GLASS INNER WEATHERSTRIP

a.
B346710

Remove the front door glass inner weatherstrip.


Hide 67832 16.REMOVE FRONT DOOR SERVICE HOLE COVER

a.
B346713

Remove the front door service hole cover.

HINT:

Remove any butyl tape remaining on the front door panel side.



Hide 68102 17.REMOVE FRONT DOOR GLASS SUB-ASSEMBLY

a.

w/ Power Window:

i.

Connect the power window regulator master switch assembly.


ii.

Connect the cable to the negative (-) battery terminal.


iii.

Move the front door glass sub-assembly so that the door glass bolts can be seen.


iv.

Disconnect the cable from the negative (-) battery terminal.


v.

Disconnect the power window regulator master switch assembly.



b.

w/o Power Window:

i.

Install the front door window regulator handle assembly.


ii.

Move the front door glass sub-assembly so that the door glass bolts can be seen.


iii.

Remove the front door window regulator handle assembly.



c.
B346714

Remove the 2 bolts.

NOTICE:

Do not damage the front door glass sub-assembly.



d.
B346715E01
0.958,0.198 1.417,0.396 0.458,0.198 10 false (1) 2.094,0.26 2.552,0.458 0.458,0.198 10 false (2)

Remove the front door glass sub-assembly as indicated by the arrows in the order shown in the illustration.

NOTICE:

Do not damage the front door glass sub-assembly.



Hide 68151D 18.REMOVE FRONT DOOR GLASS RUN

a.
B346712

Remove the front door glass run.


Hide 67664C 19.REMOVE DOOR FRAME GARNISH

a.
B356959

Disengage the clamp and remove the door frame garnish.


Hide 69820 20.REMOVE FRONT DOOR WINDOW REGULATOR ASSEMBLY (w/ Power Window)

a.
B346716C01
2.063,0.375 1.823,0.188 true 1.688,0.104 1.896,0.292 0.208,0.188 10 true *a
*a Temporary Bolt


Disconnect the connector.


b.

Loosen the temporary bolt.

NOTICE:

Do not remove the temporary bolt. If the temporary bolt is removed, the front door window regulator assembly may fall and cause damage.



c.

Remove the 5 bolts and the front door window regulator assembly.


d.

Remove the temporary bolt from the front door window regulator assembly.


Hide 69820 21.REMOVE FRONT DOOR WINDOW REGULATOR ASSEMBLY (w/o Power Window)

a.
B347100

Remove the 5 bolts and the front door window regulator assembly.


Hide 67924 22.REMOVE FRONT DOOR NO. 2 STIFFENER CUSHION

a.
B346717C01
1.979,0.833 2.313,0.833 true 2.375,0.74 2.688,0.938 0.313,0.198 10 true *a
*a Double-sided Tape


Remove the 2 bolts.


b.

Peel off the double-sided tape and remove the front door No. 2 stiffener cushion.

HINT:

Remove any double-sided tape remaining on the front door panel side.



Hide 67404F 23.REMOVE FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY

a.
B346718

Remove the 2 bolts.


b.

Disengage the guide and remove the front door rear lower frame sub-assembly.


Hide 69217F 24.REMOVE FRONT DOOR OUTSIDE HANDLE COVER (w/ Lock Cylinder)

a.
B353772C01
2.5,1.906 2.802,1.906 false 2.865,1.844 3.177,2.042 0.313,0.198 10 false *1
*1 Hole Plug


Remove the hole plug.


b.

Using a T30 "TORX" socket wrench, loosen the screw.


c.

Remove the front door outside handle cover with lock cylinder.


d.
B346720

Disengage the 2 claws and remove the front door outside handle cover from the lock cylinder.


Hide 69217F 25.REMOVE FRONT DOOR OUTSIDE HANDLE COVER (w/o Lock Cylinder)

a.
B353773C01
0.698,1.917 0.938,1.917 false 0.51,1.844 0.823,2.042 0.313,0.198 10 false *1
*1 Hole Plug


Remove the hole plug.


b.

Using a T30 "TORX" socket wrench, loosen the screw.


c.

Disengage the 2 claws and remove the front door outside handle cover.


Hide 69320 26.REMOVE FRONT DOOR LOCK ASSEMBLY

Hide 69220 27.REMOVE FRONT DOOR OUTSIDE HANDLE ASSEMBLY (w/ Smart Entry and Start System)

Hide 69220 28.REMOVE FRONT DOOR OUTSIDE HANDLE ASSEMBLY (w/o Smart Entry and Start System)

a.
B346722

Remove the front door outside handle assembly in the direction indicated by the arrow as shown in the illustration.


Hide 69241H 29.REMOVE FRONT DOOR OUTSIDE HANDLE FRONT PAD

a.
B346723

Disengage the 2 claws and remove the front door outside handle front pad.


Hide 69242E 30.REMOVE FRONT DOOR OUTSIDE HANDLE REAR PAD

a.
B346724

Disengage the 2 claws and remove the front door outside handle rear pad.


Hide 69202A 31.REMOVE FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY (w/ Smart Entry and Start System)

a.
B353774C01
0.896,1.938 1.385,1.708 true 0.427,1.438 0.844,1.219 true 0.271,1.438 0.583,1.635 0.313,0.198 10 false *b 0.75,1.906 1.063,2.104 0.313,0.198 10 false *a
*a Clamp
*b Guide


Using a clip remover, disengage the clamp.


b.

Using a T30 "TORX" socket wrench, loosen the screw.


c.

Disengage the guide and remove the front door outside handle frame sub-assembly with wire harness in the direction indicated by the arrow as shown in the illustration.


d.
B353775

Disengage the clamp and the claw, and disconnect the wire harness from the front door outside handle frame sub-assembly.


Hide 69202A 32.REMOVE FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY (w/o Smart Entry and Start System)

a.
B346727

Using a T30 "TORX" socket wrench, loosen the screw.


b.

Disengage the guide and remove the front door outside handle frame sub-assembly in the direction indicated by the arrow as shown in the illustration.


Hide 69312 33.REMOVE FRONT DOOR LOCK OPEN ROD

a.
B346728C01
1.333,2.167 1.563,2.177 true 2.802,2.448 2.927,2.219 true 1.135,2.042 1.365,2.24 0.229,0.198 10 false *a 2.896,2.083 3.125,2.281 0.229,0.198 10 false *a
*a Snap Ring


Disengage the snap ring as shown in the illustration.


b.

Remove the front door lock open rod from the front door handle frame sub-assembly.


Hide 67001A 34.REMOVE FRONT DOOR PANEL CUSHION

a.
B346729

Remove the 2 front door panel cushions.


Hide 68610 35.REMOVE FRONT DOOR CHECK ASSEMBLY

a.
B346730

Remove the 3 bolts and the front door check assembly.


Hide 67862 36.REMOVE FRONT DOOR WEATHERSTRIP

a.
B356960

Using a clip remover, remove the clip.


b.

Using a clip remover, disengage the 15 clips and remove the front door weatherstrip.