Home › Drivetrain › AXLE AND DIFFERENTIAL › STEERING KNUCKLE › 2013.08–2017.10
RM30M0E _52 Drivetrain _017093 AXLE AND DIFFERENTIAL _0090088 STEERING KNUCKLE A

AXLE AND DIFFERENTIAL  STEERING KNUCKLE  REMOVAL  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1.REMOVE FRONT WHEEL

Hide 53876A 2.REMOVE FRONT FENDER LINER (w/ ABS)

Hide 3.SEPARATE FRONT SPEED SENSOR WIRE (w/ ABS)

Hide 47313J 4.SEPARATE FRONT FLEXIBLE HOSE (w/o ABS)

Hide 6.SEPARATE FRONT DISC BRAKE CALIPER ASSEMBLY

Hide 43512 7.REMOVE FRONT DISC

Hide 48819A 8.SEPARATE FRONT STABILIZER BOLT

Hide 45047 9.SEPARATE TIE ROD END SUB-ASSEMBLY

a.
C295230

Remove the cotter pin and castle nut.


b.
C282351E01
1.781,0.854 1.906,0.469 true 1.938,0.365 2.24,0.563 0.302,0.198 10 true SST

Install SST to the threaded section of the tie rod end sub-assembly.

SST
09960-20010  (09961-02060)

NOTICE:

Make sure the upper ends of the threaded section of the tie rod end sub-assembly and SST are aligned.



c.

Using SST, separate the tie rod end sub-assembly from the steering knuckle.

C282352C01
0.76,2.344 1.042,2.073 false 0.729,0.24 0.906,0.469 true 3.448,1.823 3.083,2.281 true 0.583,2.26 0.896,2.417 0.313,0.156 10 false *a 0.563,0.135 0.875,0.292 0.313,0.156 10 false *b 6.583,0.26 6.896,0.417 0.313,0.156 10 false *c 6.448,2.281 6.76,2.438 0.313,0.156 10 false *d 4.604,2.167 4.917,2.323 0.313,0.156 10 false *e 6.594,0.583 6.906,0.781 0.313,0.198 10 false *c 1.896,1.635 2.052,1.833 0.156,0.198 10 false A 1.906,1.865 2.219,2.021 0.313,0.156 10 false B 2.771,2.198 3.083,2.354 0.313,0.156 10 false SST
*a Center Nut *b String
*c Molybdenum Grease Application Area *d Place the wrench here
*e Turn - -


SST
09960-20010  (09961-02010)

NOTICE:
·

Apply molybdenum grease to the bolt threads and the tip of SST.

·

Make sure to tie the string of SST to the vehicle to prevent SST from dropping.

·

Install SST so that A and B are parallel.

·

Be sure to place the wrench on the part indicated in the illustration.

·

Do not damage the ball joint dust cover.

·

Do not damage the front disc brake dust cover.




Hide 48069 10.SEPARATE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY

a.
C282354

Remove the clip and castle nut.


b.
C282353E01
0.917,1.771 1.5,1.229 true 0.604,1.729 0.938,1.938 0.333,0.208 10 false SST

Install SST to the threaded section of the lower ball joint.

SST
09960-20010  (09961-02060)

NOTICE:

Make sure the upper ends of the threaded section of the lower ball joint and SST are aligned.



c.

Using SST, separate the front lower No. 1 suspension arm sub-assembly from the steering knuckle.

C282355C01
1.031,0.531 0.906,0.229 true 1,2.073 0.719,2.365 true 3.677,2.302 3.375,2.427 true 0.552,2.281 0.865,2.438 0.313,0.156 10 false *a 1.792,1.646 1.948,1.802 0.156,0.156 10 false A 0.74,0.104 1.052,0.26 0.313,0.156 10 true *b 6.635,0.313 6.948,0.469 0.313,0.156 10 false *c 6.521,2.26 6.833,2.417 0.313,0.156 10 false *d 4.583,2.354 4.896,2.51 0.313,0.156 10 false *e 1.792,1.875 1.948,2.031 0.156,0.156 10 false B 6.625,0.615 6.938,0.771 0.313,0.156 10 false *c 3.052,2.375 3.375,2.531 0.323,0.156 10 false SST
*a Center Nut *b String
*c Molybdenum Grease Application Area *d Place the wrench here
*e Turn - -


SST
09960-20010  (09961-02010)

NOTICE:
·

Apply molybdenum grease to the bolt threads and the tip of SST.

·

Make sure to tie the string of SST to the vehicle to prevent SST from dropping.

·

Install SST so that A and B are parallel.

·

Be sure to place the wrench on the part indicated in the illustration.

·

Do not damage the lower ball joint dust cover.

·

Do not damage the drive shaft outboard joint boots.

·

Do not damage the front disc brake dust cover.




Hide 11.REMOVE FRONT AXLE ASSEMBLY

a.
C282325C01
2.771,1.125 3.021,0.802 3.021,0.802 2.906,1.427 true 3,0.646 3.313,0.802 0.313,0.156 10 false *a
*a Matchmark


Put matchmarks on the front drive shaft assembly and front axle hub sub-assembly.


b.

Using a plastic hammer, tap the end of the front drive shaft assembly and separate the fitting between the front drive shaft assembly and front axle assembly.

NOTICE:

Be careful not to damage the thread portion of the front drive shaft assembly.


HINT:

If it is difficult to separate the front drive shaft assembly from the front axle assembly, tap the end of the front drive shaft assembly using a brass bar and a hammer.



c.
C283589

Remove the 2 nuts, 2 bolts and front axle assembly from the front shock absorber assembly.

NOTICE:
·

Make sure not to deform the front disc brake dust cover.

·

Hang the front drive shaft assembly with wire or similar.



HINT:

Keep the bolt from rotating while turning the nut.



Hide 43502C 12.REMOVE FRONT AXLE HUB SUB-ASSEMBLY

C285071

a.

Hold the steering knuckle in a vise between aluminum plates.

NOTICE:

When using a vise, do not overtighten it.



b.

Remove the 3 bolts, front axle hub sub-assembly and front disc brake dust cover from the steering knuckle.

NOTICE:
·

Do not place the front speed sensor side so that it is facing downward, and do not allow the front speed sensor side to become damaged or contact foreign matter (w/ ABS).

·

Do not drop the front axle hub sub-assembly.



HINT:

The front axle hub sub-assembly is a component of the front speed sensor (w/ ABS).