Home › Drivetrain › AXLE AND DIFFERENTIAL › REAR AXLE HUB BOLT(for Rear Drum Brake)
RM30M0E _52 Drivetrain _017093 AXLE AND DIFFERENTIAL _0090091 REAR AXLE HUB BOLT(for Rear Drum Brake) A

AXLE AND DIFFERENTIAL  REAR AXLE HUB BOLT(for Rear Drum Brake)  REPLACEMENT  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1.REMOVE REAR WHEEL

Hide 42403 2.REMOVE REAR BRAKE DRUM SUB-ASSEMBLY

Hide 42312E 3.REMOVE REAR AXLE HUB BOLT

a.
C290887C01
1.198,0.875 0.781,0.635 true 1.615,1.74 1.292,1.49 true 2.51,1.5 1.969,1.365 false 0.594,0.521 0.792,0.677 0.198,0.156 10 true *a 1.979,1.99 2.292,2.146 0.313,0.156 10 false *b 0.927,1.917 1.24,2.073 0.313,0.156 10 false *c 1.656,1.667 1.854,1.823 0.198,0.156 10 true *a 2.573,1.438 3.031,1.635 0.458,0.198 10 false SST
*a Service Nut
*b Turn
*c Hold


Temporarily install the 2 service nuts to the 2 rear axle hub bolts as shown in the illustration.

Recommended Service Nut:
Thread Diameter Thread Pitch
12.0 mm (0.472 in.) 1.5 mm (0.0591 in.)


NOTICE:

Install the service nuts to prevent damage to the rear axle hub bolts.



b.

Using SST and a screwdriver or the equivalent to hold the rear axle hub and bearing assembly, remove the rear axle hub bolt.

SST
09628-10011  


Hide 42312E 4.INSTALL REAR AXLE HUB BOLT

a.

Temporarily install a new rear axle hub bolt to the rear axle hub and bearing assembly.


b.
C283825C03
0.531,0.615 0.656,0.219 true 0.792,0.76 1.01,0.208 true 0.698,0.115 0.885,0.271 0.188,0.156 10 false *a 1.031,0.083 1.229,0.25 0.198,0.167 10 true *b 3.115,1.271 3.427,1.427 0.313,0.156 10 false *c 1.042,1.938 1.354,2.094 0.313,0.156 10 false *d
*a Washer
*b Service Nut
*c Hold
*d Turn


Install a washer and service nut to the rear axle hub bolt as shown in the illustration.

Recommended Service Nut:
Thread Diameter Thread Pitch
12.0 mm (0.472 in.) 1.5 mm (0.0591 in.)


HINT:

Recommended thickness of the washer is 5 mm (0.197 in.) or more.



c.

Using a screwdriver or the equivalent to hold the rear axle hub and bearing assembly, install the rear axle hub bolt by tightening the service nut.


Hide 42403 5.INSTALL REAR BRAKE DRUM SUB-ASSEMBLY

Hide 6.INSTALL REAR WHEEL

Torque:
103 N*m (1050 kgf*cm, 76 ft.*lbf)

Hide 7.INSPECT AND ADJUST PARKING BRAKE LEVER TRAVEL