Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM › 2013.08–2016.04
RM30M0E _54 Brake _017098 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0090184 ANTI-LOCK BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  C146E  Open in ABS Solenoid Relay Circuit  C146F  Short in ABS Solenoid Relay Circuit  


DESCRIPTION

The ABS solenoid relay supplies power to the ABS solenoid.

The solenoid relay is turned on 1.5 seconds after the ignition switch is turned to ON, and is turned off if an open or short in the solenoid is detected by the self diagnosis performed when the engine starts running.

The ABS solenoid relay is housed in the skid control ECU (brake actuator assembly) in the actuator assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area
C146E Open in ABS Solenoid Relay Circuit When either of the following is detected:
1.

Both of the following conditions continue for 0.22 seconds or more.

·

The IG1 terminal voltage is 9.5 V or more.

·

The solenoid relay contact is open when the relay is ON.


2.

Both of the following conditions continue for 0.22 seconds or more.

·

The IG1 terminal voltage becomes lower than 9.5 V or less when the relay is turned on.

·

The relay contact remains open.



·

ABS NO. 2 fuse

·

ABS solenoid relay circuit

·

Brake actuator assembly (ABS solenoid relay)


C146F Short in ABS Solenoid Relay Circuit Immediately after the ignition switch is turned to ON, the solenoid relay contact is closed for 4.5 seconds when the relay is turned off.
·

ABS solenoid relay circuit

·

Brake actuator assembly (ABS solenoid relay)



WIRING DIAGRAM

Refer to DTCs C1468, C1469, C146A and C146B.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>C1468

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:

When C1241 is output together with C146E and/or C146F, inspect and repair the trouble areas indicated by C1241 first.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>C1241


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (+BS TERMINAL)
a.
C280112C85
1.521,0.156 1.865,0.375 0.344,0.219 2.417,0.99 2.885,0.323 true 0.125,0.104 0.438,0.302 0.313,0.198 10 false *a 1.552,0.156 1.865,0.354 0.313,0.198 10 false A35 2.927,0.219 3.24,0.417 0.313,0.198 10 false +BS
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


c.

Check the connector case and terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Disconnect the skid control ECU (brake actuator assembly) connector.


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A35-12 (+BS) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (+BS CIRCUIT)

2.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)
a.
C280112C86
1.521,0.156 1.865,0.375 0.344,0.219 1.031,0.99 0.792,0.292 true 0.125,0.104 0.438,0.302 0.313,0.198 10 false *a 1.552,0.156 1.865,0.354 0.313,0.198 10 false A35 0.385,0.219 0.781,0.417 0.396,0.198 10 false GND1
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A35-1 (GND1) - Body ground Always Below 1 Ω



b.

Reconnect the skid control ECU (brake actuator assembly) connector.


Result:
Proceed to
OK
NG



OK

3.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND1 CIRCUIT)

3.RECONFIRM DTC
HINT:

These codes are detected when a problem is determined in the skid control ECU (brake actuator assembly).

The solenoid circuits are in the skid control ECU (brake actuator assembly).

Therefore, solenoid circuit inspection and solenoid unit inspection cannot be performed. Be sure to check if any DTCs are output before replacing the skid control ECU (brake actuator assembly).


a.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

Start the engine.


c.

Drive the vehicle at the speed of 20 km/h (12 mph) or more for 30 seconds or more.


d.

Check if the same DTC is recorded.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
DTC is not output A
DTC is output B


HINT:
·

If a speed signal of 6 km/h (4 mph) or more is input to the skid control ECU (brake actuator assembly), with the ignition switch ON and the stop light switch off, the ECU performs self diagnosis of the motor and solenoid circuits.

·

If the normal system code is output (the trouble code is not output), slightly jiggle the connectors, wire harness, and fuses of the skid control ECU (brake actuator assembly). Make sure that no DTCs are output.

·

If any DTCs are output while jiggling a connector or wire harness from the skid control ECU (brake actuator assembly), inspect and repair the connector or wire harness.

·

The DTCs were probably output due to a bad connection of the connector terminal.




A

B