Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM › 2013.08–2016.04
RM30M0E _54 Brake _017098 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0090184 ANTI-LOCK BRAKE SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  Brake Warning Light Remains ON  


DESCRIPTION

The skid control ECU (brake actuator assembly) is connected to the combination meter assembly via CAN communication.

If any of the following is detected, the brake warning light remains on:

·

The skid control ECU (brake actuator assembly) connector is disconnected from the brake actuator assembly.

·

The brake fluid level is insufficient.

·

The parking brake is applied.

·

EBD operation is not possible.


WIRING DIAGRAM

C292151E01
2.823,4.219 4.677,4.438 1.854,0.219 10 false Combination Meter Assembly 2.833,4.063 3.146,4.25 0.313,0.188 10 false F38 2.875,2.885 3.188,3.073 0.313,0.188 10 false SW 2.875,1.531 3.188,1.719 0.313,0.188 10 false B 2.594,1.417 2.906,1.604 0.313,0.188 10 false 22 2.635,2.771 2.802,2.969 0.167,0.198 10 false 6 1.542,2.792 1.708,2.99 0.167,0.198 10 false 1 1.323,2.885 1.49,3.083 0.167,0.198 10 false + 0.635,2.885 0.802,3.083 0.167,0.198 10 false E 0.438,2.781 0.604,2.979 0.167,0.198 10 false 2 1.333,1.438 1.5,1.635 0.167,0.198 10 false + 1.531,1.427 1.698,1.625 0.167,0.198 10 false 1 0.583,3.177 0.896,3.365 0.313,0.188 10 false A22 0.583,1.813 0.896,2 0.313,0.188 10 false F14 0.594,3.323 2.656,3.917 2.063,0.594 10 false Brake Fluid Level Warning Switch (Brake Master Cylinder Reservoir Assembly) 0.583,1.958 2.594,2.156 2.01,0.198 10 false Parking Brake Switch Assembly 0.719,4.313 2.573,4.531 1.854,0.219 10 false : CAN Communication Line 5.479,2.563 5.792,2.75 0.313,0.188 10 false A35 5.469,2.708 7.01,3.094 1.542,0.385 10 false Skid Control ECU (Brake Actuator Assembly) 5.583,0.99 6.042,1.177 0.458,0.188 10 false GND1 5.604,0.427 6.063,0.615 0.458,0.188 10 false IG1 5.323,0.354 5.635,0.542 0.313,0.188 10 false 34 5.385,0.906 5.552,1.104 0.167,0.198 10 false 1 3.25,0.594 3.927,0.76 0.677,0.167 10 false IG1 NO. 2 1.917,0.438 2.833,0.625 0.917,0.188 10 false from IG Circuit

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if CAN communication system DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM


Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

2.CHECK IF BRAKE ACTUATOR ASSEMBLY CONNECTOR IS SECURELY CONNECTED

B

2.CHECK IF BRAKE ACTUATOR ASSEMBLY CONNECTOR IS SECURELY CONNECTED
a.

Check if the skid control ECU (brake actuator assembly) connector is securely connected.

OK:

The connector is securely connected.



Result:
Proceed to
OK
NG



OK

3.CHECK BATTERY

NG

CONNECT CONNECTOR TO ACTUATOR CORRECTLY

3.CHECK BATTERY
a.

Check the battery voltage.

Standard voltage:

11 to 14 V



Result:
Result Proceed to
OK A
NG (for 1NZ-FE) B
NG (for 2NZ-FE) C



A

4.CHECK HARNESS AND CONNECTOR (IG1 TERMINAL)

B

C

4.CHECK HARNESS AND CONNECTOR (IG1 TERMINAL)
a.
C280112C89
1.521,0.156 1.865,0.375 0.344,0.219 2.135,1.406 2.552,2.021 true 0.125,0.104 0.438,0.302 0.313,0.198 10 false *a 1.552,0.156 1.865,0.354 0.313,0.198 10 false A35 2.594,1.938 2.906,2.135 0.313,0.198 10 false IG1
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Disconnect the skid control ECU (brake actuator assembly) connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A35-34 (IG1) - Body ground Ignition switch ON 11 to 14 V



d.

Turn the ignition switch off.


Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (IG1 CIRCUIT)

5.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)
a.
C280112C90
1.542,0.188 1.917,0.406 0.375,0.219 1.031,1 0.854,0.302 true 0.073,0.063 0.385,0.26 0.313,0.198 10 false *a 1.583,0.208 1.896,0.406 0.313,0.198 10 false A35 0.458,0.219 0.875,0.417 0.417,0.198 10 false GND1
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A35-1 (GND1) - Body ground Always Below 1 Ω



b.

Reconnect the skid control ECU (brake actuator assembly) connector.


Result:
Proceed to
OK
NG



OK

6.READ VALUE USING GTS (PARKING BRAKE SWITCH ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND1 CIRCUIT)

6.READ VALUE USING GTS (PARKING BRAKE SWITCH ASSEMBLY)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.


e.

According to the display on the GTS, read the Data List.

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Parking Brake SW Parking brake switch OFF or ON OFF: Parking brake released
ON: Parking brake applied
-
Chassis > ABS/VSC/TRC > Data List
Tester Display
Parking Brake SW
50003 105 38

f.

Using the GTS, check that the switch condition displayed on the GTS changes according to the parking brake operation.

OK:

When the parking brake is operated, the display changes as shown above.



Result:
Proceed to
OK
NG



OK

7.INSPECT BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY

NG

10.INSPECT PARKING BRAKE SWITCH ASSEMBLY
7.INSPECT BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY
a.
C280126C06
1.073,1.667 1.458,1.177 true 2.271,1.688 1.938,1.177 true 0.198,0.188 0.51,0.385 0.313,0.198 10 false *a 2.323,1.729 2.479,1.927 0.156,0.198 10 false + 0.969,1.708 1.125,1.906 0.156,0.198 10 false E
*a Component without harness connected
(Brake Fluid Level Warning Switch (Brake Master Cylinder Reservoir Assembly))


Turn the ignition switch off.


b.

Remove the reservoir filler cap and strainer.


c.

Disconnect the A22 brake fluid level warning switch (brake master cylinder reservoir assembly) connector.


d.

Measure the resistance according to the value(s) in the table below.

HINT:

A float is located inside the reservoir. Its position changes according to the brake fluid level.


Standard Resistance:
Tester Connection Switch Condition Specified Condition
1 (+) - 2 (E) Switch OFF (Float up) 1.9 to 2.1 kΩ
1 (+) - 2 (E) Switch ON (Float down) Below 1 Ω


HINT:

If the switch condition is normal, adjust the brake fluid level to the MAX level.



e.

Reinstall the reservoir filler cap and strainer.


Result:
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C



A

8.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY)

B

REPLACE BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY

C

REPLACE BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY

8.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY)
a.

Disconnect the F38 combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F38-6 (SW) - A22-1 (+) Always Below 1 Ω
F38-6 (SW) or A22-1 (+) - Body ground Always 10 kΩ or higher
A22-2 (E) - Body ground Always Below 1 Ω



c.

Reconnect the F38 combination meter assembly connector.


d.

Reconnect the A22 brake fluid level warning switch (brake master cylinder reservoir assembly) connector.


Result:
Proceed to
OK
NG



OK

9.READ VALUE USING GTS (BRAKE WARNING LIGHT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.READ VALUE USING GTS (BRAKE WARNING LIGHT)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.


e.

According to the display on the GTS, read the Data List.

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Brake Warning Light Brake warning light OFF or ON OFF: Warning light off
ON: Warning light on
-
Chassis > ABS/VSC/TRC > Data List
Tester Display
Brake Warning Light
50003 105 52

f.

Check the GTS display condition of the ABS warning light.


Result:
Result Proceed to
Display of the Data List remains OFF A
Display of the Data List remains ON B


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE



A

B

10.INSPECT PARKING BRAKE SWITCH ASSEMBLY
a.
C280127C06
1.135,1.698 1.635,1.167 true 0.24,0.229 0.552,0.427 0.313,0.198 10 false *a 1.01,1.698 1.167,1.896 0.156,0.198 10 false +
*a Component without harness connected
(Parking Brake Switch Assembly)


Turn the ignition switch off.


b.

Disconnect the F14 parking brake switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
1 (+) - Body ground Switch on
(Switch pin free)
Below 1 Ω
1 (+) - Body ground Switch off
(Switch pin pushed in)
10 kΩ or higher



Result:
Proceed to
OK
NG



OK

11.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - PARKING BRAKE SWITCH ASSEMBLY)

NG

REPLACE PARKING BRAKE SWITCH ASSEMBLY

11.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - PARKING BRAKE SWITCH ASSEMBLY)
a.

Disconnect the F38 combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F38-22 (B) - F14-1 (+) Always Below 1 Ω
F38-22 (B) or F14-1 (+) - Body ground Always 10 kΩ or higher


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR