Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM(for Entry Function) › 2013.08–2014.03
RM30M0E _58 Vehicle Interior _017111 THEFT DETERRENT / KEYLESS ENTRY _0090849 SMART ENTRY AND START SYSTEM(for Entry Function) J

THEFT DETERRENT / KEYLESS ENTRY  SMART ENTRY AND START SYSTEM(for Entry Function)  All Door Entry Lock/Unlock Functions and Wireless Functions do not Operate  


DESCRIPTION

When the entry operation and wireless operation of the door lock functions do not operate, a malfunction or wave interference may be occurring in either of the following: 1) the signal communication line between the door control receiver and certification ECU (smart key ECU assembly) (the line used for entry and wireless operations); or 2) the electrical key transmitter sub-assembly. If the entry lock and wireless lock operations cannot be performed, there may be electrical key transmitter sub-assembly malfunctions, wave interference or problems in the communication which is used for the entry and wireless function between the door control receiver and certification ECU (smart key ECU assembly).

WIRING DIAGRAM

B342588E01
2.365,0.563 3.396,0.844 1.031,0.281 10 false from Battery 1.917,1.01 3.396,1.354 1.479,0.344 10 false from D/C CUT Fuse 2,1.458 3.479,1.802 1.479,0.344 10 false to IG Relay Circuit 1.854,1.885 3.333,2.229 1.479,0.344 10 false to ACC Relay Circuit 3.958,0.719 5.438,1.063 1.479,0.344 10 false AM2 NO. 2 4.115,1.156 4.656,1.469 0.542,0.313 10 false DOME 1.927,2.531 2.958,2.813 1.031,0.281 10 false 4 1.927,2.969 2.271,3.25 0.344,0.281 10 false 5 1.917,3.406 2.26,3.688 0.344,0.281 10 false 2 1.906,3.833 2.25,4.115 0.344,0.281 10 false 1 1.677,2.615 2.01,2.906 0.333,0.292 10 false +5 1.5,3.052 1.99,3.344 0.49,0.292 10 false DATA 1.51,3.479 2,3.771 0.49,0.292 10 false CSEL 1.573,3.917 2.063,4.208 0.49,0.292 10 false GND 0.719,4.458 2.104,5.052 1.385,0.594 10 false Door Control Receiver 0.719,4.292 1.208,4.583 0.49,0.292 10 false F46 5.417,0.583 5.802,0.771 0.385,0.188 10 false F43 5.406,1.458 5.792,1.646 0.385,0.188 10 false F43 5.406,1.896 5.792,2.083 0.385,0.188 10 false F43 5.406,3.917 5.792,4.104 0.385,0.188 10 false F43 5.406,1.021 5.792,1.208 0.385,0.188 10 false F44 5.406,2.615 5.792,2.802 0.385,0.188 10 false F44 5.417,3.052 5.802,3.24 0.385,0.188 10 false F44 5.479,0.396 5.698,0.594 0.219,0.198 10 false 1 5.458,0.844 5.844,1.031 0.385,0.188 10 false 33 5.458,1.271 5.844,1.458 0.385,0.188 10 false 20 5.458,1.708 5.844,1.896 0.385,0.188 10 false 21 5.49,2.427 5.875,2.615 0.385,0.188 10 false 3 5.438,2.865 5.823,3.052 0.385,0.188 10 false 22 5.458,3.302 5.844,3.49 0.385,0.188 10 false 21 5.458,3.729 5.844,3.917 0.385,0.188 10 false 10 5.417,4.656 6.958,5.25 1.542,0.594 10 false Certification ECU (Smart Key ECU Assembly) 5.708,0.583 6.198,0.875 0.49,0.292 10 false +B 5.719,1.031 6.208,1.323 0.49,0.292 10 false CUTB 5.719,1.448 6.208,1.74 0.49,0.292 10 false IG1D 5.729,1.896 6.219,2.188 0.49,0.292 10 false ACCD 5.729,2.615 6.219,2.906 0.49,0.292 10 false RCO 5.729,3.052 6.219,3.344 0.49,0.292 10 false RDAS 5.719,3.49 6.208,3.781 0.49,0.292 10 false CSEL 5.729,3.906 6.219,4.198 0.49,0.292 10 false E 5.417,3.49 5.802,3.677 0.385,0.188 10 false F44

B348667E02
0.625,1 1.083,1.198 0.458,0.198 10 false F31 0.625,1.177 2.219,1.594 1.594,0.417 10 false Front Door Courtesy Light Switch Assembly LH 0.615,2.729 2.208,3.146 1.594,0.417 10 false Front Door Courtesy Light Switch Assembly RH 0.625,2.552 1.083,2.75 0.458,0.198 10 false F32 0.615,3.938 2.208,4.354 1.594,0.417 10 false Rear Door Courtesy Light Switch Assembly LH 0.625,3.76 1.083,3.958 0.458,0.198 10 false F33 0.615,5.167 2.208,5.583 1.594,0.417 10 false Rear Door Courtesy Light Switch Assembly RH 0.625,5 1.083,5.198 0.458,0.198 10 false F34 1.74,0.563 2.198,0.76 0.458,0.198 10 false 1 1.74,2.125 2.198,2.323 0.458,0.198 10 false 1 1.729,3.344 2.188,3.542 0.458,0.198 10 false 1 1.719,4.583 2.177,4.781 0.458,0.198 10 false 1 2.313,0.5 2.771,0.698 0.458,0.198 10 false 1 2.26,0.677 2.51,0.865 0.25,0.188 10 false 2N 3.156,0.677 3.406,0.865 0.25,0.188 10 false MB 3.135,2.229 3.385,2.417 0.25,0.188 10 false F52 3.177,0.51 3.385,0.688 0.208,0.177 10 false 18 3.177,2.052 3.635,2.25 0.458,0.198 10 false 14 3.469,0.688 3.969,0.865 0.5,0.177 10 false DCTY 3.469,2.219 3.969,2.396 0.5,0.177 10 false PCTY 3.427,3.313 4.667,3.635 1.24,0.323 10 false Body Computer 4.417,1.448 4.667,1.635 0.25,0.188 10 false F52 4.417,1.896 4.667,2.083 0.25,0.188 10 false F52 5.302,1.458 5.552,1.646 0.25,0.188 10 false F44 5.313,1.896 5.563,2.083 0.25,0.188 10 false F44 4.448,1.729 4.667,1.885 0.219,0.156 10 false 16 4.5,1.271 4.719,1.427 0.219,0.156 10 false 9 5.344,1.729 5.563,1.885 0.219,0.156 10 false 13 5.333,1.281 5.552,1.438 0.219,0.156 10 false 36 4.01,1.448 4.333,1.625 0.323,0.177 10 false PRG 4.031,1.885 4.354,2.063 0.323,0.177 10 false RDA 5.625,1.448 6.135,1.635 0.51,0.188 10 false PRG3 5.635,1.885 6.135,2.083 0.5,0.198 10 false RDA3 2.469,1.104 3.385,1.667 0.917,0.563 10 false Driver Side Junction Block Assembly 5.313,3.323 6.854,3.76 1.542,0.438 10 false Certification ECU (Smart Key ECU Assembly) 0.083,0.083 1.552,0.323 1.469,0.24 12 false for LHD:

B348667E03
0.625,1 1.083,1.198 0.458,0.198 10 false F32 0.625,1.177 2.219,1.594 1.594,0.417 10 false Front Door Courtesy Light Switch Assembly RH 0.615,2.729 2.208,3.146 1.594,0.417 10 false Front Door Courtesy Light Switch Assembly LH 0.625,2.552 1.083,2.75 0.458,0.198 10 false F31 0.615,3.938 2.208,4.354 1.594,0.417 10 false Rear Door Courtesy Light Switch Assembly RH 0.625,3.76 1.083,3.958 0.458,0.198 10 false F34 0.615,5.167 2.208,5.583 1.594,0.417 10 false Rear Door Courtesy Light Switch Assembly LH 0.625,5 1.083,5.198 0.458,0.198 10 false F33 1.74,0.563 2.198,0.76 0.458,0.198 10 false 1 1.74,2.125 2.198,2.323 0.458,0.198 10 false 1 1.729,3.344 2.188,3.542 0.458,0.198 10 false 1 1.719,4.583 2.177,4.781 0.458,0.198 10 false 1 2.313,0.5 2.771,0.698 0.458,0.198 10 false 1 2.26,0.677 2.51,0.865 0.25,0.188 10 false 2N 3.156,0.677 3.406,0.865 0.25,0.188 10 false MB 3.135,2.229 3.385,2.417 0.25,0.188 10 false F52 3.177,0.51 3.385,0.688 0.208,0.177 10 false 18 3.177,2.052 3.635,2.25 0.458,0.198 10 false 14 3.469,0.688 3.969,0.865 0.5,0.177 10 false DCTY 3.469,2.219 3.969,2.396 0.5,0.177 10 false PCTY 3.427,3.313 4.667,3.635 1.24,0.323 10 false Body Computer 4.417,1.448 4.667,1.635 0.25,0.188 10 false F52 4.417,1.896 4.667,2.083 0.25,0.188 10 false F52 5.302,1.458 5.552,1.646 0.25,0.188 10 false F44 5.313,1.896 5.563,2.083 0.25,0.188 10 false F44 4.448,1.729 4.667,1.885 0.219,0.156 10 false 16 4.5,1.271 4.719,1.427 0.219,0.156 10 false 9 5.344,1.729 5.563,1.885 0.219,0.156 10 false 13 5.333,1.281 5.552,1.438 0.219,0.156 10 false 36 4.01,1.448 4.333,1.625 0.323,0.177 10 false PRG 4.031,1.885 4.354,2.063 0.323,0.177 10 false RDA 5.625,1.448 6.135,1.635 0.51,0.188 10 false PRG3 5.635,1.885 6.135,2.083 0.5,0.198 10 false RDA3 2.469,1.104 3.385,1.667 0.917,0.563 10 false Driver Side Junction Block Assembly 5.313,3.323 6.854,3.76 1.542,0.438 10 false Certification ECU (Smart Key ECU Assembly) 0.083,0.083 1.552,0.323 1.469,0.24 12 false for RHD:

CAUTION / NOTICE / HINT

NOTICE:
·

The smart entry and start system (for Entry Function) uses the CAN communication system and LIN communication system. First inspect the communication systems by following How to Proceed with Troubleshooting (Click here Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the smart entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.

·

When using the GTS with the vehicle engine switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

Check that there are no electrical key transmitter sub-assemblies in the vehicle.

·

Before performing the inspection, check that DTC B1242 (wireless door lock control) or DTC B27B0 is not output.

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before replacing the certification ECU (smart key ECU assembly), refer to the smart entry and start system (for Entry Function) precaution.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>PRECAUTION

·

After repair, confirm that no DTCs are output by performing the "DTC Output Confirmation Operation".

·

The door control receiver has a constant voltage (5 V) supply circuit connected to terminal "+5".



PROCEDURE

1.INSPECT BATTERY VOLTAGE
a.

Measure the voltage of the vehicle battery.

Standard voltage:

11 to 14 V


HINT:

It may be possible to tell whether the vehicle battery is discharged by operating the horn.

If the voltage is below 11 V, recharge or replace the vehicle battery before proceeding.



Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Open the driver door using the mechanical key built into the electrical key transmitter sub-assembly.


b.

Connect the GTS and check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>DTC CHECK / CLEAR

Body Electrical > Entry&Start > Trouble Codes
50001 125
HINT:

When using the GTS with the engine switch off to troubleshoot: Connect the GTS to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the GTS and vehicle begins.


OK:

DTC is not output.



Result:
Proceed to
OK
NG



OK

3.CHECK DOOR AJAR WARNING OPERATION

NG

3.CHECK DOOR AJAR WARNING OPERATION
a.

When door unlock by entry lock or wireless door lock operation functions even though all doors are closed, check the door ajar warning operation.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>SYSTEM DESCRIPTION

OK:

Door ajar warning does not operate.



Result:
Proceed to
OK
NG



OK

4.CHECK POWER DOOR LOCK CONTROL SYSTEM

NG

41.INSPECT FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY
4.CHECK POWER DOOR LOCK CONTROL SYSTEM
a.

When the door control switch on the power window regulator master switch assembly on the driver door is operated, check that the doors unlock and lock according to the switch operation.

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK

OK:

Door locks operate normally.



Result:
Proceed to
OK
NG



OK

5.CHECK KEY DIAGNOSTIC MODE

NG

5.CHECK KEY DIAGNOSTIC MODE

b.

Select either channel 1 or channel 2 and perform the key diagnostic mode inspection for each channel.

HINT:

If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.


i.
B354279C01
0.125,0.271 0.438,0.5 0.313,0.229 12 false *A 0.135,2.74 0.448,2.958 0.313,0.219 12 false *B 2.083,1.542 2.396,1.698 0.313,0.156 10 false *a 1.542,3.719 1.854,3.875 0.313,0.156 10 false *a
*A for LHD
*B for RHD
*a 0.7 to 1 m (2.30 to 3.28 ft.)


Check the No. 1 indoor electrical key antenna assembly (center pillar RH):

When the electrical key transmitter sub-assembly is brought within 0.7 to 1 m (2.30 to 3.28 ft.) of the front door outside handle assembly (for driver door), check that the wireless door lock buzzer sounds.

Body Electrical > Entry&Start > Utility
Tester Display
Communication Check(Key Diag Mode)
50005 125 143

ii.
B342599C02
2.365,1.01 2.531,1.01 false 0.667,1.135 2.646,0.521 2.646,0.521 1.771,1.135 true 2.688,0.406 3,0.604 0.313,0.198 10 false *a
*a Inspection Point


Check the No. 1 indoor electrical key antenna assembly (center pillar RH) and No. 1 indoor electrical key antenna assembly (center pillar LH):

When the electrical key transmitter sub-assembly is at either inspection point, check that the wireless door lock buzzer sounds.

Body Electrical > Entry&Start > Utility
Tester Display
Communication Check(Key Diag Mode)
50005 125 143

iii.
B342600C06
1.781,0.292 2.313,0.094 2.313,0.094 0.646,0.302 true 2.365,0 2.677,0.156 0.313,0.156 10 false *a
*a Inspection Point


Check the No. 2 indoor electrical key antenna assembly (rear floor):

When the electrical key transmitter sub-assembly is at either inspection point, check that the wireless door lock buzzer sounds.

Body Electrical > Entry&Start > Utility
Tester Display
Communication Check(Key Diag Mode)
50005 125 143

iv.
B342601C02
1.813,1.219 2.125,1.417 0.313,0.198 10 false *a
*a 0.7 to 1 m (2.30 to 3.28 ft.)


Check the No. 3 indoor electrical key antenna assembly (luggage compartment):

When the electrical key transmitter sub-assembly is brought within 0.7 to 1 m (2.30 to 3.28 ft.) of the No. 3 indoor electrical key antenna assembly (luggage compartment), check that the wireless door lock buzzer sounds.

Body Electrical > Entry&Start > Utility
Tester Display
Communication Check(Key Diag Mode)
50005 125 143
OK:

Wireless door lock buzzer sounds.




Result:
Result Proceed to
Diagnostic mode inspections fail for both channels A
Diagnostic mode inspections succeed for both channels B
Diagnostic mode inspection succeeds for only one of the channels C



A

6.CHECK WAVE ENVIRONMENT

B

18.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

C

31.CHECK WAVE ENVIRONMENT
6.CHECK WAVE ENVIRONMENT
a.

Bring the electrical key transmitter sub-assembly near the door control receiver and perform a wireless and entry function operation check.

HINT:
·

When the electrical key transmitter sub-assembly is brought near the door control receiver, the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.

·

If the inspection result is that the problem only occurs in certain locations or at certain times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.

·

There may be wave interference if the vehicle is near broadcasting antennas, large video displays, wireless garage door opener systems, wireless security cameras, home security systems, etc. In this case, move the vehicle to a different location and check if there is any improvement.

·

If a tool for checking electric waves, such as a signal strength meter, is available, move around the area while observing both the LF band (used by the vehicle antenna to form the detection area) and RF band (used by the electrical key transmitter sub-assembly for transmission) to check for locations where there is wave interference.



Result:
Result Proceed to
Wireless and entry functions does not operate A
Wireless and entry functions operate normally B




A

7.CHECK TRANSMITTER BATTERY

B

AFFECTED BY WAVE INTERFERENCE

7.CHECK TRANSMITTER BATTERY
a.

Check the transmitter battery level of the electrical key transmitter sub-assembly that was checked first.

i.

Press and hold the lock switch of the transmitter for 5 seconds and check the number of times that the transmitter LED illuminates.

HINT:
·

The electrical key transmitter sub-assembly sends voltage information to the certification ECU (smart key ECU assembly) when it is being used. The certification ECU (smart key ECU assembly) displays "Yes" for the "Key Low Battery" item of the Data List when this voltage information indicates 2.2 V or less.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>DATA LIST / ACTIVE TEST

·

Even if the transmitter battery is depleted, it is still possible to start the engine by holding the electrical key transmitter sub-assembly against the engine switch, depressing the brake pedal*1 or clutch pedal*2 and pressing the engine switch.

*1: for Automatic Transaxle

*2: for Manual Transaxle






Result:
Result Proceed to
Transmitter LED illuminates 3 times or more when switch is pressed and held A
Transmitter LED does not illuminate when switch is pressed and held B
Transmitter LED illuminates once or twice but not a third time C



A

8.CHECK ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY

B

17.INSPECT TRANSMITTER BATTERY (VOLTAGE)

C

8.CHECK ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY
a.

Check if there are any other registered electrical key transmitter sub-assemblies.


Result:
Result Proceed to
There are no other registered electrical key transmitter sub-assemblies A
There is another registered electrical key transmitter sub-assemblies B



A

9.ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY REGISTRATION (NEW ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY)

B

10.CHECK ENTRY DOOR LOCK OPERATION
9.ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY REGISTRATION (NEW ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY)
a.

Register a new electrical key transmitter sub-assembly.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

10.CHECK ENTRY DOOR LOCK OPERATION
10.CHECK ENTRY DOOR LOCK OPERATION
a.

Using another registered electrical key transmitter sub-assembly, check if an entry lock/unlock operation can be performed twice in succession.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>OPERATION CHECK

OK:

Entry lock/unlock operate normally.



Result:
Proceed to
OK
NG



OK

END (ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY WAS DEFECTIVE)

NG

11.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)- DOOR CONTROL RECEIVER)
11.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)- DOOR CONTROL RECEIVER)
a.

Disconnect the F43 and F44 certification ECU (smart key ECU assembly) connectors.


b.

Disconnect the F46 door control receiver connector.


c.

Measure the resistance according to the value(s) in the table below.


Standard Resistance:
Tester Connection Condition Specified Condition
F44-3 (RCO) - F46-4 (+5) Always Below 1 Ω
F44-22 (RDAS) - F46-5 (DATA) Always Below 1 Ω
F44-21 (CSEL) - F46-2 (CSEL) Always Below 1 Ω
F43-10 (E) - Body ground Always Below 1 Ω
F46-1 (GND) - Body ground Always Below 1 Ω
F44-3 (RCO) or F46-4 (+5) - Body ground Always 10 kΩ or higher
F44-22 (RDAS) or F46-5 (DATA) - Body ground Always 10 kΩ or higher
F44-21 (CSEL) or F46-2 (CSEL) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



OK

12.CHECK ENTRY DOOR LOCK OPERATION

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK ENTRY DOOR LOCK OPERATION
a.

Connect the F43 and F44 certification ECU (smart key ECU assembly) connectors.


b.

Connect the F46 door control receiver connector.



Result:
Result Proceed to
Entry lock/unlock does not operate A
Entry lock/unlock operate normally B



A

13.CHECK DOOR CONTROL RECEIVER

B

END (CONNECTOR WAS NOT CONNECTED PROPERLY)

13.CHECK DOOR CONTROL RECEIVER
a.

Measure the resistance according to the value(s) in the table below.

B327899C08
1.594,0.333 2.042,0.563 0.448,0.229 1.156,2.063 1.51,1.281 true 2.51,2.073 2.156,1.281 true 1.719,0.375 2.177,0.573 0.458,0.198 10 false F46 3.719,1.219 4.177,1.417 0.458,0.198 10 false GND 4.385,1.948 4.844,2.146 0.458,0.198 10 false *c 3.948,0.396 4.406,0.594 0.458,0.198 10 false *b 0.333,0.24 0.792,0.438 0.458,0.198 10 false *a 0.99,2.104 1.448,2.302 0.458,0.198 10 false DATA 5.396,1.958 5.854,2.156 0.458,0.198 10 false *d 2.385,2.104 2.844,2.302 0.458,0.198 10 false GND
*a Component with harness connected
(Door Control Receiver)
*b Waveform 1
*c Before lock or unlock button of electrical key transmitter sub-assembly pressed *d After lock or unlock button of electrical key transmitter sub-assembly pressed


Standard Resistance:
Tester Connection Condition Specified Condition
F46-1 (GND) - Body ground Always Below 1 Ω



b.

Using an oscilloscope, check the waveform.

OK:
Tester Connection Condition Tool Setting Specified Condition
F46-5 (DATA) - F46-1 (GND)
Procedure:
1.

Engine switch off

2.

All doors locked

3.

Lock or unlock button of electrical key transmitter subassembly not pressed → pressed


5 V/DIV., 500 ms./DIV. Pulse generation
(See waveform 1)



Result:
Proceed to
OK
NG



OK

14.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

14.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Connect the F44 certification ECU (smart key ECU assembly) connector.


b.

Connect the F46 door control receiver connector.


c.

Measure the voltage according to the value(s) in the table below.

B348668C07
1.625,0.469 2.052,0.698 0.427,0.229 2.948,2.177 2.167,1.25 true 2.25,2.188 2,1.271 true 1.344,2.188 1.677,1.271 true 0.76,0.5 1.073,0.698 0.313,0.198 10 false *a 3.854,0.583 4.167,0.781 0.313,0.198 10 false *b 2.823,2.219 3.135,2.417 0.313,0.198 10 false GND 1.26,2.219 1.573,2.417 0.313,0.198 10 false +5 2.073,2.219 2.552,2.417 0.479,0.198 10 false CSEL 3.667,1.333 3.979,1.531 0.313,0.198 10 false GND 1.719,0.5 2.031,0.698 0.313,0.198 10 false F46
*a Component with harness connected
(Door Control Receiver)
*b Waveform 1


Standard Voltage:
Tester Connection Condition Specified Condition
F46-4 (+5) - F46-1 (GND) Procedure:
1.

All doors closed

2.

All doors locked

3.

Electrical key transmitter sub-assembly switch pressed


Below 1 V → 4.5 to 5.5 V



d.

Using an oscilloscope, check the waveform.

OK:
Tester Connection Condition Tool Setting Specified Condition
F46-2 (CSEL) - F46-1 (GND) Procedure:
1.

Engine switch off

2.

All doors closed


2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform 1)



Result:
Proceed to
OK
NG



OK

15.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

15.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Replace the certification ECU (smart key ECU assembly) with a new one.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

16.CHECK WIRELESS DOOR LOCK CONTROL SYSTEM
16.CHECK WIRELESS DOOR LOCK CONTROL SYSTEM
a.

Check that the wireless door lock functions operate normally.

Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM(w/ Smart Entry and Start System)>OPERATION CHECK

OK:

Wireless door lock functions operate normally.



Result:
Proceed to
OK
NG



OK

END (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) WAS DEFECTIVE)

NG

17.INSPECT TRANSMITTER BATTERY (VOLTAGE)
a.

Inspect the transmitter battery.

i.

Remove the transmitter battery from the electrical key transmitter sub-assembly that does not operate.

Click hereVehicle Interior>DOOR LOCK>TRANSMITTER BATTERY(w/ Smart Entry and Start System)>REPLACEMENT


ii.
B327509C07
2.76,0.906 3.073,0.448 false 3.104,0.292 3.323,0.5 0.219,0.208 10 false *a
*a Lead Wire


Attach a lead wire (0.60 mm (0.0236 in.) in diameter or less including wire sheath) with tape or equivalent to the negative terminal.

NOTICE:

Do not wrap the lead wire around a terminal, wedge it between terminals, or solder it. The terminal may be deformed or damaged, and the transmitter battery will not be able to be installed correctly.



iii.

Carefully pull the lead wire out from the position shown in the illustration and install the previously removed transmitter battery.


iv.
B327510C02
2.365,1.115 1.688,0.375 false 1.49,0.281 1.802,0.479 0.313,0.198 10 false *a
*a GND


Measure the voltage of the transmitter battery.

HINT:
·

When measuring the transmitter battery voltage, bring the electrical key transmitter sub-assembly within the lock entry operating range while operating the trigger switch of a door handle to perform the measurement.

·

Perform the measurement when the key is at room temperature.

·

The key sends voltage information to the certification ECU (smart key ECU assembly) when it is transmitting. When this voltage is 2.2 V or less the Data List item "Key Low Battery" displays "Yes".

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>DATA LIST / ACTIVE TEST



Standard Voltage:
Tester Connection Condition Specified Condition
Transmitter battery positive (+) - Transmitter battery negative (-) Engine switch off, all doors closed and trigger switch pressed 2.3 to 3.2 V




Result:
Proceed to
OK
NG



OK

REPLACE ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY

NG

18.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Power Source Control / Data List.


e.

According to the display on the GTS, read the Data List.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Power Supply Condition Power supply state IG2 ON, ST ON, ALL OFF, IG1 ON or ACC ON All OFF: Engine switch off (ACC and IG)
ACC ON: Engine switch on (ACC)
IG1 ON: Engine switch on (IG) (IG1 relay on)
IG2 ON: Engine switch on (IG) (IG2 relay on)
ST ON: Sending engine start request signal
Since the IG1 and IG2 relays turn on at approximately the same time, IG1 ON may not be displayed (the IG1 relay turns on for a very short time).
Body Electrical > Power Source Control > Data List
Tester Display
Power Supply Condition
50003 223 18

f.

Measure the voltage according to the value(s) in the table below.


B342590C09
2.469,0.26 3.042,0.521 0.573,0.26 2.167,2.25 2.51,1.427 true 2.917,2.24 2.573,1.417 true 2.635,0.313 3.094,0.51 0.458,0.198 10 false F43 0.094,0.083 0.552,0.281 0.458,0.198 10 false *a 2.792,2.271 3.25,2.469 0.458,0.198 10 false IG1D 1.99,2.271 2.448,2.469 0.458,0.198 10 false ACCD
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))
- -


Standard Voltage:
Tester Connection Switch Condition Specified Condition
F43-20 (IG1D) - Body ground Engine switch off 1 V or less
Engine switch on (ACC) 1 V or less
Engine switch on (IG) 9 V or higher
F43-21 (ACCD) - Body ground Engine switch off 1 V or less
Engine switch on (ACC) 8.5 V or higher
Engine switch on (IG) 8.5 V or less


Result:
Proceed to
OK
NG



OK

19.INSPECT NO. 1 IGNITION RELAY

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

19.INSPECT NO. 1 IGNITION RELAY

OK

20.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - NO. 1 IGNITION RELAY)

NG

REPLACE NO. 1 IGNITION RELAY

20.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - NO. 1 IGNITION RELAY)

OK

21.CHECK HARNESS AND CONNECTOR (BATTERY - NO. 1 IGNITION RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

21.CHECK HARNESS AND CONNECTOR (BATTERY - NO. 1 IGNITION RELAY)

OK

22.INSPECT NO. 2 IGNITION RELAY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

22.INSPECT NO. 2 IGNITION RELAY

OK

23.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - NO. 2 IGNITION RELAY)

NG

REPLACE NO. 2 IGNITION RELAY

23.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - NO. 2 IGNITION RELAY)

OK

24.CHECK HARNESS AND CONNECTOR (BATTERY - NO. 2 IGNITION RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

24.CHECK HARNESS AND CONNECTOR (BATTERY - NO. 2 IGNITION RELAY)

OK

25.INSPECT DRIVER SIDE JUNCTION BLOCK ASSEMBLY (ACC RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

25.INSPECT DRIVER SIDE JUNCTION BLOCK ASSEMBLY (ACC RELAY)

OK

26.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - DRIVER SIDE JUNCTION BLOCK ASSEMBLY)

NG

REPLACE DRIVER SIDE JUNCTION BLOCK ASSEMBLY

26.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - DRIVER SIDE JUNCTION BLOCK ASSEMBLY)

OK

27.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

27.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - BATTERY AND BODY GROUND)
a.

Disconnect the certification ECU (smart key ECU assembly) connector.


B342591C03
4.854,0.406 5.323,0.677 0.469,0.271 1.438,0.406 1.896,0.677 0.458,0.271 2.656,1.396 2.885,2.167 true 0.396,2.146 0.646,1.396 true 5.542,1.531 5.813,2.208 true 0.083,0.073 0.396,0.271 0.313,0.198 10 false *a 0.271,2.198 0.583,2.396 0.313,0.198 10 false +B 2.854,2.219 3.167,2.417 0.313,0.198 10 false E 5.698,2.281 6.281,2.469 0.583,0.188 10 false CUTB 4.979,0.458 5.438,0.656 0.458,0.198 10 false F44 1.552,0.458 2.031,0.656 0.479,0.198 10 false F43
*a Front view of wire harness connector
(to Certification ECU (Smart Key ECU Assembly))
- -


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F43-10 (E) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F44-33 (CUTB) - Body ground Always 11 to 14 V
F43-1 (+B) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

28.CHECK ENTRY DOOR LOCK OPERATION

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

28.CHECK ENTRY DOOR LOCK OPERATION
a.

Connect the F43 and F44 certification ECU (smart key ECU assembly) connectors.



Result:
Result Proceed to
Entry lock/unlock does not operate A
Entry lock/unlock operate normally B



A

29.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

B

END (CONNECTOR WAS NOT CONNECTED PROPERLY)

29.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Replace the certification ECU (smart key ECU assembly) with a new one.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

30.CHECK WIRELESS DOOR LOCK CONTROL SYSTEM
30.CHECK WIRELESS DOOR LOCK CONTROL SYSTEM
a.

Check that the wireless door lock functions operate normally.

Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM(w/ Smart Entry and Start System)>OPERATION CHECK

OK:

Wireless door lock functions operate normally.



Result:
Proceed to
OK
NG



OK

END (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) WAS DEFECTIVE)

NG

31.CHECK WAVE ENVIRONMENT
a.

Bring the electrical key transmitter sub-assembly that was checked first near the door control receiver and select the failed channel (the channel in which the buzzer did not sound) to recheck the key diagnostic mode.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>OPERATION CHECK

HINT:
·

When the electrical key transmitter sub-assembly is brought near the door control receiver, the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.

·

If the inspection result is that the problem only occurs in certain locations or at certain times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.

·

There may be wave interference if the vehicle is near broadcasting antennas, large video displays, wireless garage door opener systems, wireless security cameras, home security systems, etc. In this case, move the vehicle to a different location and check if there is any improvement.

·

If a tool for checking electric waves, such as a signal strength meter, is available, move around the area while observing both the LF band (used by the vehicle antenna to form the detection area) and RF band (used by the electrical key transmitter sub-assembly for transmission) to check for locations where there is wave interference.



OK:

Wireless door lock buzzer sounds.



Result:
Result Proceed to
Wireless door lock buzzer does not sounds. A
Wireless door lock buzzer sounds. B



A

32.CHECK ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY

B

AFFECTED BY WAVE INTERFERENCE

32.CHECK ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY
a.

Check if there are any other registered electrical key transmitter sub-assemblies.


Result:
Result Proceed to
There are no other registered electrical key transmitter sub-assemblies A
There is another registered electrical key transmitter sub-assemblies B



A

33.ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY REGISTRATION (NEW ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY)

B

34.CHECK KEY DIAGNOSTIC MODE
33.ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY REGISTRATION (NEW ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY)
a.

Register a new electrical key transmitter sub-assembly.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

34.CHECK KEY DIAGNOSTIC MODE
34.CHECK KEY DIAGNOSTIC MODE
a.

Bring another registered electrical key transmitter sub-assembly near the door control receiver and select the failed channel (the channel in which the buzzer did not sound) to recheck the key diagnostic mode.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>OPERATION CHECK

HINT:
·

When the electrical key transmitter sub-assembly is brought near the door control receiver, the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.

·

If the inspection result is that the problem only occurs in certain locations or at certain times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.

·

There may be wave interference if the vehicle is near broadcasting antennas, large video displays, wireless garage door opener systems, wireless security cameras, home security systems, etc. In this case, move the vehicle to a different location and check if there is any improvement.

·

If a tool for checking electric waves, such as a signal strength meter, is available, move around the area while observing both the LF band (used by the vehicle antenna to form the detection area) and RF band (used by the electrical key transmitter sub-assembly for transmission) to check for locations where there is wave interference.



OK:

Wireless door lock buzzer sounds.



Result:
Proceed to
OK
NG



OK

END (ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY WAS DEFECTIVE)

NG

35.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - DOOR CONTROL RECEIVER)
35.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - DOOR CONTROL RECEIVER)
a.

Disconnect the F44 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the F46 door control receiver connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F44-21 (CSEL) - F46-2 (CSEL) Always Below 1 Ω
F44-21 (CSEL) or F46-2 (CSEL) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

36.CHECK ENTRY DOOR LOCK OPERATION

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

36.CHECK ENTRY DOOR LOCK OPERATION
a.

Connect the F44 certification ECU (smart key ECU assembly) connector.


b.

Connect the F46 door control receiver connector.



Result:
Result Proceed to
Entry lock/unlock does not operate A
Entry lock/unlock operate normally B



A

37.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

B

END (CONNECTOR WAS NOT CONNECTED PROPERLY)

37.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Connect the F44 certification ECU (smart key ECU assembly) connector.


b.

Connect the F46 door control receiver connector.


c.

Using an oscilloscope, check the waveform.

B348668C08
1.625,0.469 2.052,0.698 0.427,0.229 2.615,2.177 2.167,1.25 true 1.906,2.177 2,1.271 true 0.76,0.5 1.073,0.698 0.313,0.198 10 false *a 3.854,0.583 4.167,0.781 0.313,0.198 10 false *b 2.49,2.219 2.802,2.417 0.313,0.198 10 false GND 1.719,2.219 2.198,2.417 0.479,0.198 10 false CSEL 3.667,1.333 3.979,1.531 0.313,0.198 10 false GND 1.719,0.5 2.031,0.698 0.313,0.198 10 false F46
*a Component with harness connected
(Door Control Receiver)
*b Waveform 1


OK:
Tester Connection Condition Tool Setting Specified Condition
F46-2 (CSEL) - F46-1 (GND) Procedure:
1.

Engine switch off

2.

All doors closed


2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform 1)



Result:
Proceed to
OK
NG



OK

38.CHECK DOOR CONTROL RECEIVER

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

38.CHECK DOOR CONTROL RECEIVER
a.

Using an oscilloscope, check the waveform.

HINT:

Inspection should be performed while the electrical key antenna check in key diagnostic mode is being performed on the failed channel (the channel in which the buzzer did not sound).


B327899C09
1.594,0.521 2.115,0.74 0.521,0.219 1.177,2.083 1.479,1.26 true 2.604,2.073 2.188,1.281 true 0.115,0.115 0.427,0.313 0.313,0.198 10 false *a 1.729,0.531 2.042,0.729 0.313,0.198 10 false F46 0.99,2.104 1.49,2.323 0.5,0.219 10 false DATA 2.458,2.104 2.958,2.323 0.5,0.219 10 false GND 3.719,1.198 4.219,1.417 0.5,0.219 10 false GND 3.875,0.115 4.188,0.313 0.313,0.198 10 false *b 4.406,1.927 4.719,2.125 0.313,0.198 10 false *c 5.385,1.938 5.698,2.135 0.313,0.198 10 false *d
*a Component with harness connected
(Door Control Receiver)
*b Waveform 1
*c Before lock or unlock button of electrical key transmitter sub-assembly pressed *d After lock or unlock button of electrical key transmitter sub-assembly pressed


OK:
Tester Connection Condition Tool Setting Specified Condition
F46-5 (DATA) - F46-1 (GND) Procedure:
1.

Engine switch off

2.

All doors locked

3.

Lock or unlock button of electrical key transmitter sub-assembly not pressed → pressed


5 V/DIV., 500 ms./DIV. Pulse generation
(See waveform 1)



Result:
Proceed to
OK
NG



OK

39.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

39.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Replace the certification ECU (smart key ECU assembly) with a new one.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

40.CHECK WIRELESS DOOR LOCK CONTROL SYSTEM
40.CHECK WIRELESS DOOR LOCK CONTROL SYSTEM
a.

Check that the wireless door lock functions operate normally.

Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM(w/ Smart Entry and Start System)>OPERATION CHECK

OK:

Wireless door lock functions operate normally.



Result:
Proceed to
OK
NG



OK

END (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) WAS DEFECTIVE)

NG

41.INSPECT FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY
a.

Remove the front door courtesy light switch assembly LH and front door courtesy light switch assembly RH.

Click hereVehicle Interior>LIGHTING (INT)>FRONT DOOR COURTESY SWITCH>REMOVAL


b.

Inspect the front door courtesy light switch assembly LH and front door courtesy light switch assembly RH.

Click hereVehicle Interior>LIGHTING (INT)>FRONT DOOR COURTESY SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

42.CHECK HARNESS AND CONNECTOR (BODY COMPUTER AND DRIVER SIDE JUNCTION BLOCK ASSEMBLY - FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY)

NG

REPLACE FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY

42.CHECK HARNESS AND CONNECTOR (BODY COMPUTER AND DRIVER SIDE JUNCTION BLOCK ASSEMBLY - FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY)
a.

Disconnect the F52 body computer connector.


b.

Disconnect the 2N driver side junction block assembly connector.


c.

Disconnect the F31 front door courtesy light switch assembly LH connector.


d.

Disconnect the F32 front door courtesy light switch assembly RH connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
2N-1 - F31-1 Always Below 1 Ω
F52-14 (PCTY) - F32-1 Always Below 1 Ω
2N-1 or F31-1 - Body ground Always 10 kΩ or higher
F52-14 (PCTY) or F32-1 - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
2N-1 - F32-1 Always Below 1 Ω
F52-14 (PCTY) - F31-1 Always Below 1 Ω
2N-1 or F32-1 - Body ground Always 10 kΩ or higher
F52-14 (PCTY) or F31-1 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

43.INSPECT DRIVER SIDE JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

43.INSPECT DRIVER SIDE JUNCTION BLOCK ASSEMBLY
a.

Remove the driver side junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Remove the body computer from the driver side junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


c.

Measure the resistance according to the value(s) in the table below.

B343154C04
2.531,0.625 2.823,0.802 0.292,0.177 5.552,0.51 5.844,0.688 0.292,0.177 2.271,1.448 2.229,1.156 true 0.094,0.094 0.406,0.292 0.313,0.198 10 false *a 2.573,0.635 2.885,0.833 0.313,0.198 10 false MB 5.615,0.521 5.927,0.719 0.313,0.198 10 false 2N 2.094,1.458 2.583,1.646 0.49,0.188 10 false DCTY
*a Component without harness connected
(Driver Side Junction Block Assembly)
- -


Standard Resistance:
Tester Connection Condition Specified Condition
MB-18 (DCTY) - 2N-1 Always Below 1 Ω
MB-18 (DCTY) or 2N-1 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

44.INSPECT REAR DOOR COURTESY LIGHT SWITCH ASSEMBLY

NG

REPLACE DRIVER SIDE JUNCTION BLOCK ASSEMBLY

44.INSPECT REAR DOOR COURTESY LIGHT SWITCH ASSEMBLY
a.

Remove the rear door courtesy light switch assembly LH and rear door courtesy light switch assembly RH.

Click hereVehicle Interior>LIGHTING (INT)>REAR DOOR COURTESY SWITCH>REMOVAL


b.

Inspect the rear door courtesy light switch assembly LH and rear door courtesy light switch assembly RH.

Click hereVehicle Interior>LIGHTING (INT)>REAR DOOR COURTESY SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

45.CHECK HARNESS AND CONNECTOR (BODY COMPUTER - REAR DOOR COURTESY LIGHT SWITCH ASSEMBLY)

NG

REPLACE REAR DOOR COURTESY LIGHT SWITCH ASSEMBLY

45.CHECK HARNESS AND CONNECTOR (BODY COMPUTER - REAR DOOR COURTESY LIGHT SWITCH ASSEMBLY)
a.

Disconnect the F52 body computer connector.


b.

Disconnect the F33 rear door courtesy light switch assembly LH connector.


c.

Disconnect the F34 rear door courtesy light switch assembly RH connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F52-14 (PCTY) - F33-1 Always Below 1 Ω
F52-14 (PCTY) - F34-1 Always Below 1 Ω
F52-14 (PCTY) or F33-1 - Body ground Always 10 kΩ or higher
F52-14 (PCTY) or F34-1 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR