Home › Engine / Hybrid System › 2NZ-FE ENGINE CONTROL › SFI SYSTEM(for Automatic Transaxle) › 2013.08–2016.10
RM30M0E _51 Engine / Hybrid System _017072 2NZ-FE ENGINE CONTROL _0090867 SFI SYSTEM(for Automatic Transaxle) C

2NZ-FE ENGINE CONTROL  SFI SYSTEM(for Automatic Transaxle)  P0132  Oxygen Sensor Circuit High Voltage Bank1 Sensor1  


DESCRIPTION

Refer to DTC P0031.

Click hereEngine / Hybrid System>2NZ-FE ENGINE CONTROL>SFI SYSTEM(for Automatic Transaxle)>P0031

HINT:

Sensor 1 refers to the sensor mounted in front of the Three-Way Catalytic Converter (TWC) and located near the engine assembly.


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0132 Oxygen Sensor Circuit High Voltage Bank1 Sensor1 Heated oxygen sensor voltage output exceeds 1.2 V for more than 10 seconds (2 trip detection logic).
·

Short in heated oxygen sensor (sensor 1) circuit

·

Heated oxygen sensor (sensor 1)

·

ECM internal circuit malfunction


Comes on DTC stored

MONITOR DESCRIPTION

A106749E06
5.604,1.094 5.333,1.094 false 5.052,2.198 5.052,1.927 false 4.844,2.458 4.573,2.458 false 4.104,1.75 3.906,1.75 false 0.083,0.583 1.063,1 0.979,0.417 10 false Heated Oxygen Sensor Voltage 0.792,1.323 1.188,1.531 0.396,0.208 10 false 0.5 V 0.802,2.271 1.198,2.469 0.396,0.198 10 false 0.4 V 3.563,1.656 4.021,1.875 0.458,0.219 10 false Pass 1.313,2.719 1.729,2.948 0.417,0.229 10 false Lean 1.302,0.76 1.688,0.969 0.385,0.208 10 false Rich 4.333,2.385 4.719,2.583 0.385,0.198 10 false Fail 4.948,1.76 5.24,1.958 0.292,0.198 10 false Fail 5.083,1.01 5.385,1.208 0.302,0.198 10 false Fail 2.646,3 5.292,3.292 2.646,0.292 10 false Pass / Fail Definition of Voltage Malfunction 6.396,3 6.719,3.24 0.323,0.24 10 false Time

The ECM uses the heated oxygen sensor information to regulate the air fuel ratio close to a stoichiometric air fuel ratio. This maximizes the catalytic converter's ability to purify the exhaust gases. The heated oxygen sensor detects oxygen levels in the exhaust gas and sends this signal to the ECM.

The inner surface of the sensor element is exposed to outside air. The outer surface of the sensor element is exposed to the exhaust gas. The sensor element is made of platinum coated zirconia and an integrated heating element. The heated oxygen sensor's output voltage changes suddenly in the vicinity of the stoichiometric air fuel ratio. The heated oxygen sensor generates output voltage between 0 V and 1 V in response to the oxygen concentration in the exhaust gas. When the front heated oxygen sensor voltage is 0.45 V or higher, the ECM judges that the air fuel ratio is rich. When it is 0.45 V or less, the ECM judges that the air fuel ratio is lean.

If the front heated oxygen sensor output voltage exceeds 1.2 V for 10 seconds, the ECM illuminates the MIL (2 trip detection logic) and stores DTC P0132.

MONITOR STRATEGY

Required Sensors/Components (Main) Heated oxygen sensor (sensor 1)
Required Sensors/Components (Related) Crankshaft position sensor
Vehicle speed sensor
Frequency of Operation Once per driving cycle

TYPICAL ENABLING CONDITIONS

Engine Running
Battery voltage 11 V or higher

TYPICAL MALFUNCTION THRESHOLDS

Heated oxygen sensor voltage 1.2 V or higher

COMPONENT OPERATING RANGE

Heated oxygen sensor voltage Fluctuates for a second

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

Start the engine.

7.

Idle the engine for 10 seconds or more.

8.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

9.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



10.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

11.

Input the DTC: P0132.

12.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




CAUTION / NOTICE / HINT

HINT:

Malfunctioning areas can be identified by performing the Control the Injection Volume for A/F Sensor function provided in the Active Test. The Control the Injection Volume for A/F Sensor function can help to determine whether the heated oxygen sensor and other potential trouble areas are malfunctioning.

The following instructions describe how to conduct the Control the Injection Volume for A/F Sensor operation using the GTS.

1.

Connect the GTS to the DLC3.

2.

Start the engine.

3.

Turn the GTS on.

4.

Warm up the engine and run the engine at an engine speed of 2500 rpm for approximately 90 seconds.

5.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor / O2S B1S1 and O2S B1S2.

6.

Perform the Active Test operation with the engine idling (press the 12.5% or -12.5% button to change the fuel injection volume).

7.

Monitor the output voltages of the heated oxygen sensors (O2S B1S1 and O2S B1S2) displayed on the GTS.



HINT:
·

The Control the Injection Volume for A/F Sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 12.5%.

·

Each sensor reacts in accordance with increases and decreases in the fuel injection volume.



GTS Display
(Sensor)
Injection Volume Status Voltage
O2S B1S1
(Heated oxygen sensor (sensor 1))
12.5% Rich Higher than 0.5 V
-12.5% Lean Below 0.4 V
O2S B1S2
(Heated oxygen sensor (sensor 2))
12.5% Rich Higher than 0.5 V
-12.5% Lean Below 0.4 V

NOTICE:

The heated oxygen sensor (sensor 1) has an output delay of a few seconds and the heated oxygen sensor (sensor 2) has a maximum output delay of approximately 20 seconds.


A299377E01
3.375,0.313 5.552,0.698 2.177,0.385 10 false Heated Oxygen Sensor (Sensor 2) Output Voltage 0.885,0.323 3.063,0.708 2.177,0.385 10 false Heated Oxygen Sensor (Sensor 1) Output Voltage 0.406,1.771 0.563,1.979 0.156,0.208 10 false 1 0.281,0.406 0.677,0.604 0.396,0.198 10 false Case 5.802,0.323 6.823,0.729 1.021,0.406 10 false Main Suspected Trouble Area 0.417,3.75 0.594,3.969 0.177,0.219 10 false 2 0.427,5.688 0.583,5.896 0.156,0.208 10 false 3 0.438,7.74 0.594,7.948 0.156,0.208 10 false 4 6.208,1.813 6.344,2.01 0.135,0.198 10 false - 5.677,3.094 6.833,3.531 1.156,0.438 10 false - Heated oxygen sensor (sensor 1) 5.677,3.542 6.698,4.125 1.021,0.583 10 false - Heated oxygen sensor (sensor 1) heater 5.688,4.135 6.708,4.719 1.021,0.583 10 false - Heated oxygen sensor (sensor 1) circuit 5.677,5.104 6.781,5.479 1.104,0.375 10 false - Heated oxygen sensor (sensor 2) 5.677,5.521 6.729,6.094 1.052,0.573 10 false - Heated oxygen sensor (sensor 2) heater 5.688,6.125 6.719,6.698 1.031,0.573 10 false - Heated oxygen sensor (sensor 2) circuit 5.688,7.01 6.615,7.438 0.927,0.427 10 false - Fuel injector assembly 5.677,7.427 6.646,7.625 0.969,0.198 10 false - Fuel pressure 5.677,7.698 6.74,8.594 1.063,0.896 10 false - Gas leak from exhaust system (Air fuel ratio extremely rich or lean) 1.469,1.25 1.927,1.448 0.458,0.198 10 false 12.5% 1.51,3.198 1.969,3.406 0.458,0.208 10 false 12.5% 3.969,3.208 4.427,3.417 0.458,0.208 10 false 12.5% 3.958,1.25 4.448,1.438 0.49,0.188 10 false 12.5% 1.51,7.125 1.979,7.354 0.469,0.229 10 false 12.5% 1.521,5.156 1.979,5.344 0.458,0.188 10 false 12.5% 3.979,5.167 4.438,5.354 0.458,0.188 10 false 12.5% 3.979,7.125 4.417,7.333 0.438,0.208 10 false 12.5% 1.417,1.521 1.906,1.708 0.49,0.188 10 false -12.5% 3.906,1.51 4.396,1.698 0.49,0.188 10 false -12.5% 3.917,3.458 4.406,3.646 0.49,0.188 10 false -12.5% 1.458,3.469 1.948,3.656 0.49,0.188 10 false -12.5% 1.469,5.406 1.958,5.594 0.49,0.188 10 false -12.5% 3.938,5.406 4.427,5.594 0.49,0.188 10 false -12.5% 3.938,7.385 4.427,7.573 0.49,0.188 10 false -12.5% 1.458,7.375 1.948,7.563 0.49,0.188 10 false -12.5% 0.76,1 1.813,1.229 1.052,0.229 10 false Injection Volume 0.792,1.927 1.729,2.156 0.938,0.229 10 false Output Voltage 0.792,8.208 2.052,8.406 1.26,0.198 10 false Almost no reaction 3.26,8.208 4.521,8.406 1.26,0.198 10 false Almost no reaction 0.781,4.302 2.042,4.5 1.26,0.198 10 false Almost no reaction 3.26,6.26 4.521,6.458 1.26,0.198 10 false Almost no reaction 5.042,8.104 5.302,8.292 0.26,0.188 10 false NG 2.563,8.104 2.823,8.292 0.26,0.188 10 false NG 5.031,6.146 5.292,6.333 0.26,0.188 10 false NG 2.552,4.198 2.813,4.385 0.26,0.188 10 false NG 3.229,1 4.281,1.229 1.052,0.229 10 false Injection Volume 3.229,2.948 4.281,3.177 1.052,0.229 10 false Injection Volume 0.76,2.948 1.813,3.177 1.052,0.229 10 false Injection Volume 0.75,4.906 1.802,5.135 1.052,0.229 10 false Injection Volume 3.229,4.906 4.281,5.135 1.052,0.229 10 false Injection Volume 3.219,6.854 4.271,7.083 1.052,0.229 10 false Injection Volume 0.771,6.865 1.823,7.094 1.052,0.229 10 false Injection Volume 0.844,2.271 1.969,2.469 1.125,0.198 10 false Higher than 0.5 V 1.167,2.49 1.99,2.677 0.823,0.188 10 false Below 0.4 V 3.323,2.219 4.448,2.417 1.125,0.198 10 false Higher than 0.5 V 3.646,2.448 4.469,2.635 0.823,0.188 10 false Below 0.4 V 3.25,1.917 4.188,2.146 0.938,0.229 10 false Output Voltage 5.125,2.333 5.406,2.531 0.281,0.198 10 false OK 2.646,2.375 2.927,2.573 0.281,0.198 10 false OK 0.802,3.885 1.74,4.115 0.938,0.229 10 false Output Voltage 3.26,3.885 4.198,4.115 0.938,0.229 10 false Output Voltage 5.135,4.302 5.417,4.5 0.281,0.198 10 false OK 3.344,4.198 4.469,4.396 1.125,0.198 10 false Higher than 0.5 V 3.656,4.427 4.479,4.615 0.823,0.188 10 false Below 0.4 V 3.271,5.854 4.208,6.083 0.938,0.229 10 false Output Voltage 0.802,5.844 1.74,6.073 0.938,0.229 10 false Output Voltage 0.865,6.146 1.99,6.344 1.125,0.198 10 false Higher than 0.5 V 1.177,6.385 2,6.573 0.823,0.188 10 false Below 0.4 V 2.667,6.26 2.948,6.458 0.281,0.198 10 false OK 0.802,7.781 1.74,8.01 0.938,0.229 10 false Output Voltage 3.271,7.781 4.208,8.01 0.938,0.229 10 false Output Voltage

HINT:
·

Following the Control the Injection Volume for A/F Sensor procedure enables technicians to check and graph the voltage outputs of both the heated oxygen sensors.

·

To display the graph, enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor / O2S B1S1 and O2S B1S2, and then press the graph button on the Data List view.



NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:
·

Sensor 1 refers to the sensor closest to the engine assembly.

·

Sensor 2 refers to the sensor farthest away from the engine assembly.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK ANY OTHER DTC OUTPUT (IN ADDITION TO DTC P0132)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read the DTCs.

Powertrain > Engine and ECT > Trouble Codes
50001 234

Result:
Result Proceed to
DTC P0132 and other DTCs are output A
DTC P0132 is output B


HINT:

If any DTCs other than P0132 is output, troubleshoot those DTCs first.



A

B

2.READ VALUE USING GTS (O2S B1S1)
2.READ VALUE USING GTS (O2S B1S1)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / O2S B1S1.

Powertrain > Engine and ECT > Data List
Tester Display
O2S B1S1
50003 234 42

e.

Allow the engine to run at 2500 rpm for 3 minutes.


f.

Depress the accelerator pedal quickly until the engine rpm reaches 4000 rpm 3 times.


Result:
Result Proceed to
Higher than 1.0 V A
1.0 V or less B



A

3.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT)

B

5.PERFORM CONFIRMATION DRIVING PATTERN
3.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT)
a.

Disconnect the B24 heated oxygen sensor (sensor 1) connector.


b.

Disconnect the B31 ECM connector.


c.

Measure the resistance according to the value in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B24-1 (HT1A) - B24-3 (OX1A) Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

4.INSPECT HEATED OXYGEN SENSOR (SENSOR 1) (HEATER RESISTANCE)
4.INSPECT HEATED OXYGEN SENSOR (SENSOR 1) (HEATER RESISTANCE)
a.

Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR

NG

5.PERFORM CONFIRMATION DRIVING PATTERN
a.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


Result:
Proceed to
NEXT



NEXT

6.CHECK WHETHER DTC OUTPUT RECURS (DTC P0132)
6.CHECK WHETHER DTC OUTPUT RECURS (DTC P0132)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read the DTCs.

Powertrain > Engine and ECT > Trouble Codes
50001 234

Result:
Result Proceed to
DTC P0132 is output A
DTC is not output B



A

B