Home › Engine / Hybrid System › 2NZ-FE ENGINE CONTROL › SFI SYSTEM(for Automatic Transaxle) › 2013.08–2016.10
RM30M0E _51 Engine / Hybrid System _017072 2NZ-FE ENGINE CONTROL _0090867 SFI SYSTEM(for Automatic Transaxle) C

2NZ-FE ENGINE CONTROL  SFI SYSTEM(for Automatic Transaxle)  P0031  Oxygen (A/F) Sensor Heater Control Circuit Low (Bank 1 Sensor 1)  P0032  Oxygen (A/F) Sensor Heater Control Circuit High (Bank 1 Sensor 1)  P0037  Oxygen Sensor Heater Control Circuit Low (Bank 1 Sensor 2)  P0038  Oxygen Sensor Heater Control Circuit High (Bank 1 Sensor 2)  


DESCRIPTION

The heated oxygen sensor is used to monitor the oxygen concentration in the exhaust gas. For optimum catalytic converter operation, the air fuel mixture must be maintained near the ideal stoichiometric air fuel ratio. The heated oxygen sensor output voltage changes suddenly in the vicinity of the stoichiometric air fuel ratio. The ECM adjusts the fuel injection time so that the air fuel ratio is nearly stoichiometric. The heated oxygen sensor generates a voltage between 0 and 1 V in response to the oxygen concentration in the exhaust gas.

If the oxygen concentration in the exhaust gas increases, the air fuel ratio is described as lean. The heated oxygen sensor voltage drops to below 0.45 V and the heated oxygen sensor informs the ECM of the lean condition. If there is little oxygen in the exhaust gas, the air fuel ratio is described as rich. The heated oxygen sensor voltage increases to above 0.45 V and the heated oxygen sensor informs the ECM of the rich condition.

A112653E13
0.948,2.385 0.656,2.385 false 3.375,0.406 3.115,0.646 false 3.427,1.031 2.885,1.031 true 3.427,0.719 2.854,0.906 true 3.427,1.625 2.906,1.479 false 3.427,1.927 2.771,1.698 true 3.427,2.208 2.875,1.896 true 2.323,2.115 1.771,2.427 true 0.24,2.313 0.667,2.479 0.427,0.167 10 false Cover 1.313,2.438 2.198,2.615 0.885,0.177 10 false Exhaust Gas 1.865,0.26 2.719,0.458 0.854,0.198 10 false Atmosphere 3.396,0.344 3.979,0.552 0.583,0.208 10 false Housing 3.448,0.667 4.688,0.833 1.24,0.167 10 false Platinum Electrode 3.448,0.969 4.667,1.323 1.219,0.354 10 false Solid Electrolyte (Zirconia Element) 3.448,1.865 3.958,2.042 0.51,0.177 10 false Heater 3.448,2.146 4.635,2.354 1.188,0.208 10 false Coating (Ceramic) 3.448,1.563 4.688,1.729 1.24,0.167 10 false Platinum Electrode 4.115,0.333 5.094,0.531 0.979,0.198 10 false Output Voltage 4.792,2.25 6.833,2.469 2.042,0.219 10 false Richer - Air Fuel Ratio - Leaner 5.115,0.177 6.479,0.385 1.365,0.208 10 false Ideal Air Fuel Mixture

HINT:
·

Sensor 1 refers to the sensor mounted in front of the Three-Way Catalytic Converter (TWC) and located near the engine assembly.

·

Sensor 2 refers to the sensor mounted behind the TWC and located far from the engine assembly.



A259951E04
4.563,1.521 5.094,1.896 0.531,0.375 10 false OX1A 4.563,0.948 5.073,1.396 0.51,0.448 10 false HT1A 5.167,2.667 5.698,2.958 0.531,0.292 10 false MREL 5.167,2.094 5.708,2.479 0.542,0.385 10 false EX1A 5.167,1.51 5.688,1.844 0.521,0.333 10 false OX1A 5.167,0.948 5.656,1.24 0.49,0.292 10 false HT1A 3.896,0.792 4.344,0.948 0.448,0.156 10 false Heater 3.885,1.302 4.344,1.458 0.458,0.156 10 false Sensor 2.313,2.375 3.021,2.604 0.708,0.229 10 false EFI 0.208,1.073 0.99,1.302 0.781,0.229 10 false from Battery 1.094,1.219 1.76,1.365 0.667,0.146 10 false EFI-MAIN 0.958,3.406 1.458,3.573 0.5,0.167 10 false Ground 3.469,2 5.021,2.438 1.552,0.438 10 false Heated Oxygen Sensor 3.448,1.51 3.656,1.656 0.208,0.146 10 false E2 3.448,0.958 3.646,1.104 0.198,0.146 10 false +B 0.063,0.021 2.531,0.208 2.469,0.188 10 false Reference (System Diagram Sensor 1): 5.948,3.344 6.313,3.5 0.365,0.156 10 false ECM 2.927,1.25 3.625,1.458 0.698,0.208 10 false EFI NO. 2

A259951E05
4.563,1.521 5.094,1.896 0.531,0.375 10 false OX1B 4.563,0.948 5.073,1.396 0.51,0.448 10 false HT1B 5.167,2.667 5.698,2.958 0.531,0.292 10 false MREL 5.167,2.094 5.708,2.479 0.542,0.385 10 false EX1B 5.167,1.51 5.688,1.844 0.521,0.333 10 false OX1B 5.167,0.948 5.656,1.24 0.49,0.292 10 false HT1B 3.896,0.792 4.344,0.948 0.448,0.156 10 false Heater 3.885,1.302 4.344,1.458 0.458,0.156 10 false Sensor 2.313,2.375 3.021,2.604 0.708,0.229 10 false EFI 0.219,1.073 1.031,1.302 0.813,0.229 10 false from Battery 1.094,1.219 1.74,1.458 0.646,0.24 10 false EFI-MAIN 0.958,3.406 1.458,3.573 0.5,0.167 10 false Ground 3.469,1.979 5.021,2.417 1.552,0.438 10 false Heated Oxygen Sensor 3.448,1.51 3.656,1.656 0.208,0.146 10 false E2 3.448,0.958 3.646,1.104 0.198,0.146 10 false +B 0.063,0.021 2.531,0.208 2.469,0.188 10 false Reference (System Diagram Sensor 2): 5.948,3.344 6.313,3.5 0.365,0.156 10 false ECM 2.927,1.25 3.625,1.458 0.698,0.208 10 false EFI NO. 2

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0031 Oxygen (A/F) Sensor Heater Control Circuit Low (Bank 1 Sensor 1) Heated oxygen sensor heater current below 0.25 A when heater operates with +B greater than 10.5 V (1 trip detection logic).
·

Open in Heated oxygen sensor heater circuit

·

Heated oxygen sensor heater

·

ECM


Comes on DTC stored
P0032 Oxygen (A/F) Sensor Heater Control Circuit High (Bank 1 Sensor 1) Heated oxygen sensor heater current exceeds 2 A when heater operates (1 trip detection logic).
·

Short in Heated oxygen sensor heater circuit

·

Heated oxygen sensor heater

·

ECM


Comes on DTC stored
P0037 Oxygen Sensor Heater Control Circuit Low (Bank 1 Sensor 2) Heated oxygen sensor heater current below 0.25 A when heater operates with +B greater than 10.5 V (1 trip detection logic).
·

Open in Heated oxygen sensor heater circuit

·

Heated oxygen sensor heater

·

ECM


Comes on DTC stored
P0038 Oxygen Sensor Heater Control Circuit High (Bank 1 Sensor 2) Heated oxygen sensor heater current exceeds 2 A when heater operates (1 trip detection logic).
·

Short in Heated oxygen sensor heater circuit

·

Heated oxygen sensor heater

·

ECM


Comes on DTC stored

MONITOR DESCRIPTION

The sensing portion of the heated oxygen sensor has a zirconia element which is used to detect the oxygen concentration in the exhaust. If the zirconia element is at the proper temperature and the difference in the oxygen concentration between the inside and outside surface of the sensor is large, the zirconia element will generate voltage signals. In order to increase the oxygen concentration detecting capacity in the zirconia element, the ECM supplements the heat from the exhaust with heat from a heating element inside the sensor. When the current in the heated oxygen sensor heater is out of the standard operating range, the ECM interprets this as a fault in the heated oxygen sensor heater. The ECM illuminates the MIL and stores a DTC.

Example: The ECM stores either DTC P0032 or P0038 when the current in the heated oxygen sensor heater is more than 2 A despite the heater being OFF. Conversely, when the heater current is less than 0.25 A despite the heater being ON, DTC P0031 or P0037 is stored.

MONITOR STRATEGY

Required Sensors/Components (Main) Heated oxygen sensor heater
Required Sensors/Components (Related) Vehicle speed sensor
Frequency of Operation Continuous

TYPICAL ENABLING CONDITIONS

Battery voltage 10.5 V or higher
Engine Running
Starter OFF

P0031 and P0037
Duration of following conditions 2 seconds or more
Learned heater current during heater OFF Completed

P0032 and P0038
Duration of following conditions 0.1 seconds or more
Learned heater current during heater OFF Completed

TYPICAL MALFUNCTION THRESHOLDS

P0031 and P0037
Heated oxygen sensor heater current when heated oxygen sensor heater ON Less than 0.25 A

P0032 and P0038
Heated oxygen sensor heater current when heated oxygen sensor heater OFF More than 2 A

COMPONENT OPERATING RANGE

Heated oxygen sensor heater current 0.25 to 2 A (when idling with warm engine and battery voltage 11 to 14 V)

CONFIRMATION DRIVING PATTERN

A198819E80
0.75,0.969 1.396,1.167 0.646,0.198 10 false 3000 rpm 0.948,1.74 1.354,1.896 0.406,0.156 10 false Idling 0.208,2.01 1.417,2.354 1.208,0.344 10 false Ignition Switch ON 1.927,2.135 2.167,2.302 0.24,0.167 10 false [A] 2.76,1.625 2.958,1.823 0.198,0.198 10 false [B] 4.021,0.865 4.281,1.094 0.26,0.229 10 false [C] 5.385,1.604 5.604,1.781 0.219,0.177 10 false [D] 2.271,2.594 3.469,2.75 1.198,0.156 10 false 5 minutes or more 4.875,2.604 6.073,2.76 1.198,0.156 10 false 5 minutes or more 3.854,2.615 4.427,2.781 0.573,0.167 10 false 1 minute 5.979,3.031 6.177,3.229 0.198,0.198 10 false [E]

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on [A].

6.

Start the engine and idle it for 5 minutes or more [B].

7.

With the vehicle stationary, depress the accelerator pedal and maintain an engine speed of 3000 rpm for 1 minute [C].

8.

Idle the engine for 5 minutes or more [D].

9.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [E].

10.

Read DTCs.

HINT:
·

If a DTC is output, the system is malfunctioning.

·

If a DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

12.

Input the DTC: P0031, P0032, P0037 or P0038.

13.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit




HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [B] through [E] again.



WIRING DIAGRAM

A300993E01
5.625,1.052 6.083,1.25 0.458,0.198 10 false B31 5.635,1.771 6.094,1.969 0.458,0.198 10 false B31 5.646,2.49 6.104,2.688 0.458,0.198 10 false B31 5.635,3.74 6.094,3.938 0.458,0.198 10 false F82 5.635,5.167 6.094,5.365 0.458,0.198 10 false F82 5.646,4.458 6.104,4.656 0.458,0.198 10 false F82 1.75,2.281 2.208,2.479 0.458,0.198 10 false 2L 2.438,1.052 2.896,1.25 0.458,0.198 10 false 2H 0.802,2.281 1.26,2.479 0.458,0.198 10 false 2J 0.292,2.281 0.75,2.479 0.458,0.198 10 false 2B 0.125,2.281 0.583,2.479 0.458,0.198 10 false 1 0.625,2.281 1.083,2.479 0.458,0.198 10 false 7 1.542,2.281 2,2.479 0.458,0.198 10 false 9 2.479,0.885 2.938,1.083 0.458,0.198 10 false 4 5.698,0.885 6.156,1.083 0.458,0.198 10 false 1 5.708,3.573 6.167,3.771 0.458,0.198 10 false 6 5.635,6.156 6.094,6.354 0.458,0.198 10 false F83 4.417,2.385 4.875,2.583 0.458,0.198 10 false 4 4.385,5.083 4.844,5.281 0.458,0.198 10 false 4 4.385,4.333 4.844,4.531 0.458,0.198 10 false 3 4.406,1.677 4.865,1.875 0.458,0.198 10 false 3 4.396,0.958 4.802,1.146 0.406,0.188 10 false 1 4.375,3.635 4.781,3.823 0.406,0.188 10 false 1 3.052,2.688 3.51,2.938 0.458,0.25 10 false B24 3.052,5.323 3.51,5.521 0.458,0.198 10 false F58 3.063,2.813 4.833,3.198 1.771,0.385 10 false Heated Oxygen Sensor (Sensor 1) 3.052,5.458 4.823,5.844 1.771,0.385 10 false Heated Oxygen Sensor (Sensor 2) 3.219,0.938 3.677,1.135 0.458,0.198 10 false 2 3.208,3.635 3.667,3.833 0.458,0.198 10 false 2 5.677,2.302 6.135,2.5 0.458,0.198 10 false 33 5.667,1.594 6.125,1.792 0.458,0.198 10 false 25 5.677,4.292 6.135,4.49 0.458,0.198 10 false 27 5.677,5 6.135,5.198 0.458,0.198 10 false 26 5.708,5.979 6.167,6.177 0.458,0.198 10 false 8 3.365,0.958 3.823,1.156 0.458,0.198 10 false +B 4,0.948 4.458,1.146 0.458,0.198 10 false HT1A 3.99,1.677 4.448,1.875 0.458,0.198 10 false OX1A 4.156,2.385 4.615,2.583 0.458,0.198 10 false E2 3.375,3.646 3.833,3.844 0.458,0.198 10 false +B 4.135,5.083 4.594,5.281 0.458,0.198 10 false E2 3.979,3.646 4.438,3.844 0.458,0.198 10 false HT1B 3.969,4.333 4.427,4.531 0.458,0.198 10 false OX1B 5.969,1.063 6.427,1.26 0.458,0.198 10 false HT1A 5.948,1.771 6.406,1.969 0.458,0.198 10 false OX1A 5.948,3.74 6.406,3.938 0.458,0.198 10 false HT1B 5.948,4.448 6.406,4.646 0.458,0.198 10 false OX1B 5.958,5.167 6.417,5.365 0.458,0.198 10 false EX1B 5.958,2.479 6.417,2.677 0.458,0.198 10 false EX1A 5.958,6.156 6.417,6.354 0.458,0.198 10 false MREL 1.229,1.823 1.688,2.021 0.458,0.198 10 false EFI 2,1.208 2.396,1.646 0.396,0.438 10 false EFI NO. 2 0.448,1.656 0.844,2.094 0.396,0.438 10 false EFI-MAIN 0.469,3.979 0.865,4.417 0.396,0.438 10 false MAIN 0.635,5.729 1.281,6.177 0.646,0.448 10 false Battery 6.146,6.49 6.542,6.927 0.396,0.438 10 false ECM 4.469,6.708 5.323,7.104 0.854,0.396 10 false *: Shielded 5.156,2.271 5.313,2.469 0.156,0.198 10 false * 1.875,2.49 2.875,3.573 1,1.083 10 false Driver Side Junction Block Assembly 0.458,4.958 1.313,5.229 0.854,0.271 10 false FL MAIN

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:
·

Sensor 1 refers to the sensor closest to the engine assembly.

·

Sensor 2 refers to the sensor farthest away from the engine assembly.

·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

Change the fuel injection volume using the Control the Injection Volume for A/F sensor function provided in the Active Test and monitor the heated oxygen sensor output voltage.

Click hereEngine / Hybrid System>2NZ-FE ENGINE CONTROL>SFI SYSTEM(for Automatic Transaxle)>P0132

If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.



PROCEDURE

1.INSPECT HEATED OXYGEN SENSOR (SENSOR 1 OR 2) (HEATER RESISTANCE)
a.

Inspect the heated oxygen sensor (sensor 1 or 2).

HINT:
·

For the heated oxygen sensor (sensor 1) inspection, refer to the following procedures.

Click hereEngine / Hybrid System>2NZ-FE ENGINE CONTROL>HEATED OXYGEN SENSOR(for Sensor 1)>INSPECTION

·

For the heated oxygen sensor (sensor 2) inspection, refer to the following procedures.

Click hereEngine / Hybrid System>2NZ-FE ENGINE CONTROL>HEATED OXYGEN SENSOR(for Sensor 2)>INSPECTION




Result:
Result Proceed to
OK A
NG (for sensor 1) B
NG (for sensor 2) C



A

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF HEATED OXYGEN SENSOR (SENSOR 1 OR 2))

B

C

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF HEATED OXYGEN SENSOR (SENSOR 1 OR 2))
a.
A258725C01
0.646,0.854 1.042,1.146 0.396,0.292 0.656,2.271 1.083,2.563 0.427,0.292 1.792,2.313 2.479,1.844 true 1.76,0.896 2.448,0.427 true 0.115,0.094 0.323,0.26 0.208,0.167 10 false *a 1.094,0.833 1.323,1.021 0.229,0.188 10 false *b 1.135,2.219 1.365,2.406 0.229,0.188 10 false *c 2.469,0.302 2.708,0.51 0.24,0.208 10 false +B 2.521,1.719 2.802,1.938 0.281,0.219 10 false +B 0.708,0.917 0.99,1.063 0.281,0.146 10 false B24 0.74,2.333 1.021,2.479 0.281,0.146 10 false F58
*a Front view of wire harness connector
(to Heated Oxygen Sensor)
*b for sensor 1
*c for sensor 2


Disconnect the heated oxygen sensor (sensor 1 or 2) connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage (for sensor 1):
Tester Connection Switch Condition Specified Condition
B24-2 (+B) - Body ground Ignition switch ON 11 to 14 V


Standard Voltage (for sensor 2):
Tester Connection Switch Condition Specified Condition
F58-2 (+B) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR (SENSOR 1 OR 2) - ECM)

NG

5.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR (SENSOR 1 OR 2) - DRIVER SIDE JUNCTION BLOCK ASSEMBLY)
3.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR (SENSOR 1 OR 2) - ECM)
a.

Disconnect the B24 or F58 heated oxygen sensor (sensor 1 or 2) connector.


b.

Disconnect the B31 and F82 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (for sensor 1):
Tester Connection Condition Specified Condition
B24-1 (HT1A) - B31-1 (HT1A) Always Below 1 Ω
B24-1 (HT1A) or B31-1 (HT1A) - Body ground Always 10 kΩ or higher


Standard Resistance (for sensor 2):
Tester Connection Condition Specified Condition
F58-1 (HT1B) - F82-6 (HT1B) Always Below 1 Ω
F58-1 (HT1B) or F82-6 (HT1B) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0031, P0032, P0037 OR P0038)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0031, P0032, P0037 OR P0038)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Click hereEngine / Hybrid System>2NZ-FE ENGINE CONTROL>SFI SYSTEM(for Automatic Transaxle)>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Clear DTCs
50002 234

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON.


g.

Turn the GTS on.


h.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


i.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


j.

Read the DTCs.

Powertrain > Engine and ECT > Trouble Codes
50001 234

Result:
Result Proceed to
DTC is not output A
DTC P0031, P0032, P0037 or P0038 are output B



A

B

5.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR (SENSOR 1 OR 2) - DRIVER SIDE JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the B24 or F58 heated oxygen sensor (sensor 1 or 2 ) connector.


b.

Remove the driver side junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (for sensor 1):
Tester Connection Condition Specified Condition
B24-2 (+B) - 2H-4 Always Below 1 Ω
B24-2 (+B) or 2H-4 - Body ground Always 10 kΩ or higher


Standard Resistance (for sensor 2):
Tester Connection Condition Specified Condition
F58-2 (+B) - 2H-4 Always Below 1 Ω
F58-2 (+B) or 2H-4 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR