Home › Engine / Hybrid System › 2NZ-FE ENGINE CONTROL › SFI SYSTEM(for Manual Transaxle) › 2013.08–2016.10
RM30M0E _51 Engine / Hybrid System _017072 2NZ-FE ENGINE CONTROL _0090868 SFI SYSTEM(for Manual Transaxle) C

2NZ-FE ENGINE CONTROL  SFI SYSTEM(for Manual Transaxle)  P0100  Mass Air Flow Circuit  P0102  Mass Air Flow Circuit Low  P0103  Mass Air Flow Circuit High  


DESCRIPTION

The mass air flow meter is a sensor that measures the amount of air flowing through the throttle valve.

The ECM uses this information to determine the fuel injection time and to provide the appropriate air fuel ratio.

Inside the mass air flow meter, there is a heated platinum wire which is exposed to the flow of intake air.

By applying a specific electrical current to the wire, the ECM heats it to a given temperature. The flow of incoming air cools both the wire and an internal thermistor, affecting their resistance. To maintain a constant current value, the ECM varies the voltage applied to these components in the mass air flow meter. The voltage level is proportional to the air flow through the sensor, and the ECM uses it to calculate the intake air volume.

The circuit is constructed so that the platinum hot wire and the temperature sensor create a bridge circuit, and the power transistor is controlled so that the potentials of A and B remain equal to maintain the predetermined temperature.

HINT:

When any of these DTCs are stored, the ECM enters fail-safe mode. During fail-safe mode, the ignition timing is calculated by the ECM, according to the engine speed and throttle valve position. Fail-safe mode continues until a pass condition is detected.


A234789E10
4.865,1.323 4.26,2.135 true 2.49,1.073 2.292,1.469 false 5.125,1.542 5.448,2.125 true 1.448,0.281 1.969,1.438 true 2.25,0.563 3.323,0.719 1.073,0.156 10 false Power Transistor 2.021,0.073 2.385,0.25 0.365,0.177 10 false +B 2.531,0.979 4.229,1.135 1.698,0.156 10 false Platinum Hot Wire (Heater) 2.938,1.583 3.896,1.74 0.958,0.156 10 false Output Voltage 2.792,2.146 4.479,2.302 1.688,0.156 10 false Platinum Hot Wire (Heater) 4.896,2.146 7,2.302 2.104,0.156 10 false Temperature Sensor (Thermistor) 0.135,0.177 1.438,0.51 1.302,0.333 10 false Temperature Sensor (Thermistor) 1.656,1.49 1.802,1.646 0.146,0.156 10 false A 2.49,1.49 2.646,1.646 0.156,0.156 10 false B

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0100 Mass Air Flow Circuit Mass air flow meter voltage less than 0.2 V or higher than 4.9 V for 3 seconds (1 trip detection logic).
·

Open or short in mass air flow meter circuit

·

Mass air flow meter

·

ECM


Comes on DTC stored
P0102 Mass Air Flow Circuit Low Mass air flow meter voltage less than 0.2 V for 3 seconds (1 trip detection logic).
·

Open or short in mass air flow meter circuit

·

Mass air flow meter

·

ECM


Comes on DTC stored
P0103 Mass Air Flow Circuit High Mass air flow meter voltage higher than 4.9 V for 3 seconds (1 trip detection logic).
·

Open or short in mass air flow meter circuit

·

Mass air flow meter

·

ECM


Comes on DTC stored

HINT:

When any of these DTCs are stored, check the mass air flow rate by entering the following menus: Powertrain / Engine and ECT / Data List / MAF.

Mass Air Flow Rate (gm/sec) Malfunction
Approximately 0.0
·

Open in mass air flow meter power source circuit

·

Open or short in VG circuit


160.0 or more Open in E2G circuit


MONITOR DESCRIPTION

If there is a defect in the mass air flow meter or an open or short circuit, the voltage level deviates from the normal operating range. The ECM interprets this deviation as a malfunction in the mass air flow meter and stores a DTC.

Example:

When the sensor output voltage remains below 0.2 V, or higher than 4.9 V for more than 3 seconds, the ECM stores a DTC.

MONITOR STRATEGY

Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

Wait 5 seconds or more.

7.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

8.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



9.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

10.

Input the DTC: P0100, P0102 or P0103.

11.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and the DTC judgment result again.




WIRING DIAGRAM

A300998E03
5.875,1.396 6.188,1.594 0.313,0.198 10 false VG 5.865,1.875 6.177,2.073 0.313,0.198 10 false E2G 5.083,1.396 5.396,1.594 0.313,0.198 10 false VG 5.01,1.896 5.323,2.094 0.313,0.198 10 false E2G 5.844,3.26 6.354,3.458 0.51,0.198 10 false MREL 4.125,1.063 4.438,1.26 0.313,0.198 10 false +B 5.344,1.396 5.656,1.594 0.313,0.198 10 false 5 5.344,1.906 5.656,2.104 0.313,0.198 10 false 4 5.542,3.271 5.854,3.469 0.313,0.198 10 false F81 5.531,2 5.844,2.198 0.313,0.198 10 false B32 5.531,1.49 5.844,1.688 0.313,0.198 10 false B32 5.615,1.823 5.927,2.021 0.313,0.198 10 false 7 5.563,1.302 5.875,1.5 0.313,0.198 10 false 18 5.615,3.063 5.927,3.26 0.313,0.198 10 false 2 3.979,1.094 4.292,1.292 0.313,0.198 10 false 3 3.229,1.188 3.542,1.385 0.313,0.198 10 false 2H 3.115,2.135 3.427,2.333 0.313,0.198 10 false 2L 1.146,2.146 1.458,2.344 0.313,0.198 10 false 2J 0.635,1.188 0.948,1.385 0.313,0.198 10 false 2B 3.271,1.01 3.583,1.208 0.313,0.198 10 false 4 2.906,2.135 3.219,2.333 0.313,0.198 10 false 9 0.948,2.135 1.271,2.344 0.323,0.208 10 false 7 0.646,1.01 0.969,1.219 0.323,0.208 10 false 1 0.906,1.313 1.573,1.635 0.667,0.323 10 false EFI-MAIN 2.542,1.302 3.208,1.625 0.667,0.323 10 false EFI NO. 2 1.875,1.99 2.542,2.313 0.667,0.323 10 false EFI 0.375,2.625 1.042,2.948 0.667,0.323 10 false MAIN 0.542,3.958 1.208,4.281 0.667,0.323 10 false Battery 6.25,3.729 6.917,4.052 0.667,0.323 10 false ECM 1.333,2.375 3.104,2.781 1.771,0.406 10 false Driver Side Junction Block Assembly 4.135,2.583 5.469,2.875 1.333,0.292 10 false Mass Air Flow Meter 4.135,2.427 4.448,2.625 0.313,0.198 10 false B25 0.375,3.323 1.042,3.646 0.667,0.323 10 false FL MAIN

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (MASS AIR FLOW METER)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / MAF.

Powertrain > Engine and ECT > Data List
Tester Display
MAF
50003 234 3

e.

Read the value displayed on the GTS.


Result:
Mass Air Flow Rate (gm/sec) Proceed to
0.0 A
160.0 or more B
Between 1.0 and 160.0* C


HINT:

*: The value must change when the throttle valve is opened or closed with the engine running.



A

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF MASS AIR FLOW METER)

B

6.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)

C

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF MASS AIR FLOW METER)
a.
A162182C08
0.25,1.292 0.635,1.49 0.385,0.198 1.74,1.396 2.063,0.604 true 0.323,1.323 0.635,1.479 0.313,0.156 10 false B25 0.229,0.167 0.396,0.333 0.167,0.167 10 false *a 2.083,0.521 2.521,0.708 0.438,0.188 10 false +B
*a Front view of wire harness connector
(to Mass Air Flow Meter)


Disconnect the mass air flow meter connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B25-3 (+B) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)

NG

5.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - DRIVER SIDE JUNCTION BLOCK ASSEMBLY)
3.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
a.

Disconnect the B25 mass air flow meter connector.


b.

Disconnect the B32 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B25-5 (VG) - B32-18 (VG) Always Below 1 Ω
B25-4 (E2G) - B32-7 (E2G) Always Below 1 Ω
B25-5 (VG) or B32-18 (VG) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT MASS AIR FLOW METER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT MASS AIR FLOW METER
a.

Inspect the mass air flow meter, referring to the On-vehicle Inspection for Mass Air Flow Meter.

Click hereEngine / Hybrid System>2NZ-FE ENGINE CONTROL>MASS AIR FLOW METER>ON-VEHICLE INSPECTION


b.

Inspect the mass air flow meter, referring to the Inspection for Mass Air Flow Meter.

Click hereEngine / Hybrid System>2NZ-FE ENGINE CONTROL>MASS AIR FLOW METER>INSPECTION


c.

Inspect the function of the mass air flow meter.

i.

Connect the GTS to the DLC3.


ii.

Turn the ignition switch to ON.


iii.

Turn the GTS on.


iv.

Enter the following menus: Powertrain / Engine and ECT / Data List / MAF.

Powertrain > Engine and ECT > Data List
Tester Display
MAF
50003 234 3

v.

Start the engine.


vi.

Check that the MAF value changes when the engine is raced.

OK:

The reading changes.




Result:
Proceed to
OK
NG



OK

NG

5.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - DRIVER SIDE JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the B25 mass air flow meter connector.


b.

Remove the driver side junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


c.

Measure the resistance according to the value(s) in the table below.


Standard Resistance:
Tester Connection Condition Specified Condition
B25-3 (+B) - 2H-4 Always Below 1 Ω
B25-3 (+B) or 2H-4 - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
a.

Disconnect the B25 mass air flow meter connector.


b.

Disconnect the B32 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B25-4 (E2G) - B32-7 (E2G) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (SENSOR GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (SENSOR GROUND)
a.

Disconnect the B25 mass air flow meter connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B25-4 (E2G) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG