Home › Drivetrain › CLUTCH › CLUTCH PEDAL(for RHD) › 2013.08–2017.10
RM30M0E _52 Drivetrain _017089 CLUTCH _0091163 CLUTCH PEDAL(for RHD) A

CLUTCH  CLUTCH PEDAL(for RHD)  INSTALLATION  


PROCEDURE

Hide 31321 1.INSTALL CLUTCH PEDAL PAD

a.

Install the clutch pedal pad to the clutch pedal sub-assembly.


Hide 31322 2.INSTALL CLUTCH PEDAL STOPPER

a.

Install the clutch pedal stopper to the clutch pedal sub-assembly.


Hide 31301C 3.INSTALL CLUTCH PEDAL BUSH

a.

Install a new clutch pedal bush to the clutch pedal sub-assembly.

HINT:

Install the clutch pedal bush from the right side of the vehicle.



b.
C235134C01
0,0 3.427,0 false
V100135

MP Grease


Apply MP grease to the inside of the clutch pedal bush.


Hide 31301B 4.INSTALL NO. 1 CLUTCH PEDAL CUSHION

a.

Install the No. 1 clutch pedal cushion to the clutch pedal sub-assembly.


Hide 31324A 5.INSTALL CLUTCH PEDAL SHAFT COLLAR

a.
C235135C02
0.5,1.844 0.5,1.51 false 1.271,1.635 1.271,1.302 false 3.063,1.177 3.063,0.844 false 3.01,1.198 3.323,1.396 0.313,0.198 10 false *1 1.229,1.667 1.542,1.865 0.313,0.198 10 false *2 0.448,1.865 0.76,2.063 0.313,0.198 10 false *1
*1 Clutch Pedal Spring Bush
*2 Clutch Pedal Shaft Collar
V100135

MP Grease


Apply MP grease to both sides of 2 new clutch pedal spring bushes.


b.

Install the clutch pedal shaft collar and 2 clutch pedal spring bushes to the clutch pedal sub-assembly.


Hide 31301 6.INSTALL CLUTCH PEDAL SUB-ASSEMBLY

a.

Install the clutch pedal sub-assembly to the clutch pedal support sub-assembly with the bolt and nut.

Torque:
36.8 N*m (375 kgf*cm, 27 ft.*lbf)

HINT:
·

Install the bolt from the right side of the vehicle.

·

Turn the nut while holding the bolt.




Hide 31301F 7.INSTALL CLUTCH PEDAL STOPPER BOLT

a.

Install the clutch pedal stopper bolt to the clutch pedal support sub-assembly and temporarily tighten the lock nut.

HINT:

Tighten the lock nut to the specified torque when adjusting the clutch pedal.



Hide 84520 8.INSTALL CLUTCH START SWITCH ASSEMBLY

a.

Install the clutch start switch assembly to the clutch pedal support sub-assembly with the nut.

Torque:
15.7 N*m (160 kgf*cm, 12 ft.*lbf)

NOTICE:
·

Insert the protrusion of the clutch start switch assembly into the hole in the clutch pedal support sub-assembly.

·

To prevent damage to the clutch start switch assembly, make sure not to rotate it during installation.




Hide 55107A 9.INSTALL CLUTCH PEDAL SUPPORT SUB-ASSEMBLY

a.
C283230E01
1.885,1.052 2.042,1.25 0.156,0.198 10 true 1 2.229,1.271 2.385,1.469 0.156,0.198 10 false 2 2.802,0.281 2.958,0.479 0.156,0.198 10 false 3 2.49,1.635 2.646,1.833 0.156,0.198 10 false 4

Temporarily install the clutch pedal support sub-assembly to the body and clutch master cylinder assembly with the 2 bolts and 2 nuts.


b.

Tighten the 2 bolts and 2 nuts in the order shown in the illustration.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)


c.

Engage the clamp to the clutch pedal support sub-assembly.


d.

Connect the connector to the clutch start switch assembly.


Hide 31453 10.CONNECT CLUTCH MASTER CYLINDER PUSH ROD CLEVIS

a.
C245271C01
0,0 3.427,0 false
V100135

MP Grease


Apply MP grease to the push rod clevis pin.


b.

Connect the clutch master cylinder push rod clevis to the clutch pedal sub-assembly with the push rod clevis pin.

HINT:

Install the push rod clevis pin from the right side of the vehicle.



c.

Install a new clip to the push rod clevis pin.


Hide 31301A 11.INSTALL CLUTCH PEDAL SPRING

a.

Install the clutch pedal spring to the clutch pedal sub-assembly and clutch pedal support sub-assembly.


Hide 45209 12.CONNECT STEERING SLIDING YOKE SUB-ASSEMBLY

Hide 45259A 13.INSTALL COLUMN HOLE COVER SILENCER SHEET

Hide 14.INSPECT AND ADJUST CLUTCH PEDAL

Hide 15.INSPECT CLUTCH START SYSTEM

Hide 55432B 16.INSTALL LOWER INSTRUMENT PANEL FINISH PANEL

Hide 55606 17.INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY