Home › Vehicle Interior › DOOR LOCK › WIRELESS DOOR LOCK CONTROL SYSTEM(w/ Smart Entry and Start System) › 2013.08–2013.12
RM30M0E _58 Vehicle Interior _017110 DOOR LOCK _0091389 WIRELESS DOOR LOCK CONTROL SYSTEM(w/ Smart Entry and Start System) J

DOOR LOCK  WIRELESS DOOR LOCK CONTROL SYSTEM(w/ Smart Entry and Start System)  No Answer-Back  


DESCRIPTION

In some cases, wireless door lock control functions are normal but the hazard warning light and wireless door lock buzzer answer-back function does not operate. In such cases, hazard warning light and wireless door lock buzzer signal outputs from the body computer may be malfunctioning.

WIRING DIAGRAM

E281445
2.25,1.25 4.135,1.438 1.885,0.188 10 false Combination Meter Assembly 2.25,2.177 4.323,2.365 2.073,0.188 10 false Front Door Lock Assembly LH*1 2.167,3.104 4.24,3.292 2.073,0.188 10 false Front Door Lock Assembly RH*2 0.979,5.188 2.719,5.396 1.74,0.208 10 false Wireless Door Lock Buzzer 3.438,5.188 4.979,5.604 1.542,0.417 10 false Certification ECU (Smart Key ECU Assembly) 5.969,5.229 6.958,5.438 0.99,0.208 10 false Body Computer 5.969,5.083 6.26,5.271 0.292,0.188 10 false F52 4.698,4.177 4.99,4.365 0.292,0.188 10 false F44 4.708,3.74 5,3.927 0.292,0.188 10 false F44 3.521,4.51 3.813,4.698 0.292,0.188 10 false F43 3.844,4.521 4.219,4.698 0.375,0.177 10 false BZR 4.208,4.188 4.635,4.365 0.427,0.177 10 false PRG3 4.229,3.76 4.656,3.938 0.427,0.177 10 false RDA3 6.042,4.156 6.469,4.333 0.427,0.177 10 false PRG 6.052,3.719 6.479,3.896 0.427,0.177 10 false RDA 6.052,1.76 6.542,1.958 0.49,0.198 10 false LSWD 3.313,1.646 3.74,1.823 0.427,0.177 10 false LSSR 3.323,2.583 3.75,2.76 0.427,0.177 10 false LSSR 6.031,0.792 6.344,1 0.313,0.208 10 false HAZ 3.375,0.771 3.688,0.979 0.313,0.208 10 false HAZ 2.281,4.375 2.469,4.563 0.188,0.188 10 false B 1.365,4.365 1.552,4.552 0.188,0.188 10 false E 1.135,4.365 1.323,4.552 0.188,0.188 10 false 2 2.49,4.375 2.677,4.563 0.188,0.188 10 false 1 3.583,4.333 3.75,4.542 0.167,0.208 10 false 2 4.74,3.573 4.948,3.781 0.208,0.208 10 false 13 4.75,4.01 4.938,4.219 0.188,0.208 10 false 36 5.771,3.625 5.979,3.833 0.208,0.208 10 false 16 5.833,4.063 6.042,4.271 0.208,0.208 10 false 9 5.75,1.656 5.958,1.865 0.208,0.208 10 false 15 5.823,0.677 6.031,0.885 0.208,0.208 10 false 6 3.771,0.635 3.979,0.844 0.208,0.208 10 false 3 3.792,1.646 4,1.854 0.208,0.208 10 false 8 3.781,2.583 3.99,2.792 0.208,0.208 10 false 7 2.469,2.583 2.677,2.792 0.208,0.208 10 false 8 2.479,1.646 2.688,1.854 0.208,0.208 10 false 7 2.25,1.125 2.552,1.333 0.302,0.208 10 false F39 2.25,2.042 2.552,2.25 0.302,0.208 10 false H3 2.156,2.969 2.458,3.177 0.302,0.208 10 false G2 0.969,5.052 1.271,5.26 0.302,0.208 10 false A30 2.688,1.646 2.875,1.833 0.188,0.188 10 false E 2.708,2.583 2.896,2.771 0.188,0.188 10 false E 0.083,5.5 0.906,5.708 0.823,0.208 10 false *1: for LHD 1.167,5.5 1.99,5.708 0.823,0.208 10 false *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the certification ECU (smart key ECU assembly), refer to Service Bulletin.

·

Troubleshooting should be started after confirming that the customize status of the wireless door lock buzzer answer-back function has been switched on.

·

Before performing the inspection, check that DTC B27B0 (Smart Entry and Start System) is not output.



PROCEDURE

1.CHECK WIRELESS DOOR LOCK CONTROL FUNCTIONS
a.

Check the wireless door lock control function using the electrical key transmitter sub-assembly.


Result:
Result Proceed to
Wireless door lock/unlock operates properly. A
Wireless door lock/unlock does not operate properly. B



A

2.INSPECT FRONT DOOR LOCK ASSEMBLY

B

2.INSPECT FRONT DOOR LOCK ASSEMBLY
a.

for LHD

i.

Remove the front door lock assembly LH.

Click hereVehicle Interior>DOOR LOCK>FRONT DOOR LOCK(for TMT Made)>REMOVAL


ii.

Inspect the front door lock assembly LH.

Click hereVehicle Interior>DOOR LOCK>FRONT DOOR LOCK(for TMT Made)>INSPECTION



b.

for RHD

i.

Remove the front door lock assembly RH.

Click hereVehicle Interior>DOOR LOCK>FRONT DOOR LOCK(for TMT Made)>REMOVAL


ii.

Inspect the front door lock assembly RH.

Click hereVehicle Interior>DOOR LOCK>FRONT DOOR LOCK(for TMT Made)>INSPECTION



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (FRONT DOOR LOCK ASSEMBLY - BODY COMPUTER)

NG

REPLACE FRONT DOOR LOCK ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (FRONT DOOR LOCK ASSEMBLY - BODY COMPUTER)
a.

for LHD

i.

Disconnect the H3 front door lock assembly LH connector.



b.

for RHD

i.

Disconnect the G2 front door lock assembly RH connector.



c.

Disconnect the F52 body computer connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
H3-8 (LSSR) - F52-15 (LSWD) Always Below 1 Ω
H3-7 (E) - Body ground Always Below 1 Ω
H3-8 (LSSR) or F52-15 (LSWD) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
G2-7 (LSSR) - F52-15 (LSWD) Always Below 1 Ω
G2-8 (E) - Body ground Always Below 1 Ω
G2-7 (LSSR) or F52-15 (LSWD) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK WIRELESS ANSWER-BACK OPERATION

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK WIRELESS ANSWER-BACK OPERATION
a.

Check the wireless answer-back operation using the electrical key transmitter sub-assembly.


Result:
Result Proceed to
Only wireless door lock buzzer answer-back does not occur. A
Only hazard warning light answer-back does not occur. B



A

5.PERFORM ACTIVE TEST USING GTS (WIRELESS BUZZER)

B

11.CHECK HAZARD WARNING LIGHTS OPERATION
5.PERFORM ACTIVE TEST USING GTS (WIRELESS BUZZER)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Entry&Start / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Entry&Start > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Wireless Buzzer Operation Wireless door lock buzzer OFF/ON -
Body Electrical > Entry&Start > Active Test
Tester Display
Wireless Buzzer Operation
50004 125 31

Result:
Result Proceed to
Wireless door lock buzzer does not turn on/off. A
Wireless door lock buzzer turns on/off. B



A

6.CHECK HARNESS AND CONNECTOR (WIRELESS DOOR LOCK BUZZER - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))

B

6.CHECK HARNESS AND CONNECTOR (WIRELESS DOOR LOCK BUZZER - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
a.

Disconnect the A30 wireless door lock buzzer connector.


b.

Disconnect the F43 certification ECU (smart key ECU assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A30-1 (B) - F43-2 (BZR) Always Below 1 Ω
A30-2 (E) - Body ground Always Below 1 Ω
A30-1 (B) or F43-2 (BZR) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.REPLACE WIRELESS DOOR LOCK BUZZER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.REPLACE WIRELESS DOOR LOCK BUZZER
a.

Temporarily replace the wireless door lock buzzer with a new one.

Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK BUZZER>REMOVAL


Result:
Proceed to
NEXT



NEXT

8.PERFORM ACTIVE TEST USING GTS (WIRELESS BUZZER)
8.PERFORM ACTIVE TEST USING GTS (WIRELESS BUZZER)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Entry&Start / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Entry&Start > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Wireless Buzzer Operation Wireless door lock buzzer OFF/ON -
Body Electrical > Entry&Start > Active Test
Tester Display
Wireless Buzzer Operation
50004 125 31

Result:
Result Proceed to
Wireless door lock buzzer does not turn on/off. A
Wireless door lock buzzer turns on/off. B



A

9.REPLACE BODY COMPUTER

B

END (WIRELESS DOOR LOCK BUZZER WAS DEFECTIVE)

9.REPLACE BODY COMPUTER
a.

Replace the body computer with a new one.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


Result:
Proceed to
NEXT



NEXT

10.CHECK WIRELESS DOOR LOCK BUZZER OPERATION
10.CHECK WIRELESS DOOR LOCK BUZZER OPERATION
a.

Check the operation of the wireless answer-back function.

OK:

Wireless answer-back function operates normally.



Result:
Proceed to
OK
NG



OK

END (BODY COMPUTER WAS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

11.CHECK HAZARD WARNING LIGHTS OPERATION
a.

Check that the hazard warning lights blink when the hazard warning signal switch is pressed.

OK:

Hazard warning lights blink.



Result:
Proceed to
OK
NG



OK

12.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BODY COMPUTER)

NG

GO TO LIGHTING SYSTEM (PROCEED TO HAZARD WARNING SWITCH CIRCUIT)

12.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BODY COMPUTER)
a.

Disconnect the F39 combination meter assembly connector.


b.

Disconnect the F52 body computer connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F39-3 (HAZ) - F52-6 (HAZ) Always Below 1 Ω
F39-3 (HAZ) or F52-6 (HAZ) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR