Home › Vehicle Interior › DOOR LOCK › WIRELESS DOOR LOCK CONTROL SYSTEM(w/o Smart Entry and Start System) › 2013.08–2014.03
RM30M0E _58 Vehicle Interior _017110 DOOR LOCK _0091390 WIRELESS DOOR LOCK CONTROL SYSTEM(w/o Smart Entry and Start System) J

DOOR LOCK  WIRELESS DOOR LOCK CONTROL SYSTEM(w/o Smart Entry and Start System)  Only Wireless Control Function is Inoperative  


DESCRIPTION

The door control receiver receives signals from the door control transmitter assembly and sends these signals to the body computer. The body computer then controls all doors by sending lock/unlock signals to each door, and sends hazard flasher signals to the combination meter assembly.

WIRING DIAGRAM

E281456E01
0.417,4.583 1.833,4.802 1.417,0.219 10 false Door Control Receiver 5.75,4.583 6.76,4.802 1.01,0.219 10 false Body Computer 3.708,4.167 5.167,4.573 1.458,0.406 10 false Unlock Warning Switch Assembly 5.833,3.729 6.219,3.917 0.385,0.188 10 false KSW 5.833,2.917 6.219,3.104 0.385,0.188 10 false PRG 5.823,2.125 6.208,2.313 0.385,0.188 10 false RDA 1.354,2.135 1.74,2.323 0.385,0.188 10 false RDA 1.344,2.969 1.729,3.156 0.385,0.188 10 false PRG 1.354,3.74 1.74,3.927 0.385,0.188 10 false GND 1.438,1.344 1.823,1.531 0.385,0.188 10 false +B 1.792,1.219 2,1.438 0.208,0.219 10 false 5 1.781,2.031 1.99,2.25 0.208,0.219 10 false 2 1.792,2.833 2,3.052 0.208,0.219 10 false 3 1.781,3.635 1.99,3.854 0.208,0.219 10 false 1 5.542,2.031 5.75,2.25 0.208,0.219 10 false 16 5.583,2.833 5.792,3.052 0.208,0.219 10 false 9 4.792,3.615 5,3.833 0.208,0.219 10 false 1 5.583,3.615 5.792,3.833 0.208,0.219 10 false 8 3.833,3.615 4.042,3.833 0.208,0.219 10 false 2 3.698,4 4,4.229 0.302,0.229 10 false F27 5.75,4.438 6.052,4.667 0.302,0.229 10 false F52 0.417,4.438 0.719,4.667 0.302,0.229 10 false F47 2.479,1.5 3,1.708 0.521,0.208 10 false DOME 3.823,1.323 4.625,1.531 0.802,0.208 10 false from Battery

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

When replacing or inspecting the door control receiver and wire harness, do not change the position or length of the wire harness. If the wire harness is too close to the door control receiver, wireless function performance may be affected.



PROCEDURE

1.CHECK POWER DOOR LOCK OPERATION
a.

Check the power door lock operation.

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK

OK:

Locked doors unlock



Result:
Proceed to
OK
NG



OK

2.INSPECT UNLOCK WARNING SWITCH ASSEMBLY

NG

2.INSPECT UNLOCK WARNING SWITCH ASSEMBLY
a.

Remove the unlock warning switch assembly.

Click hereVehicle Interior>DOOR LOCK>UNLOCK WARNING SWITCH>REMOVAL


b.

Inspect the unlock warning switch assembly.

Click hereVehicle Interior>DOOR LOCK>UNLOCK WARNING SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (UNLOCK WARNING SWITCH ASSEMBLY - BODY COMPUTER)

NG

REPLACE UNLOCK WARNING SWITCH ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (UNLOCK WARNING SWITCH ASSEMBLY - BODY COMPUTER)
a.

Disconnect the F27 unlock warning switch assembly connector.


b.

Disconnect the F52 body computer connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
F27-1 - F52-8 (KSW) Always Below 1 Ω
F27-2 - Body ground Always Below 1 Ω
F27-1 or F52-8 (KSW) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.SWITCH TO SELF-DIAGNOSTIC MODE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.SWITCH TO SELF-DIAGNOSTIC MODE
a.

Switch to self-diagnostic mode by operating the ignition key cylinder.

i.

Make sure the vehicle is in its initial condition. Then insert the key into the ignition key cylinder and remove it.


ii.

Within 5 seconds of removing the key, insert the key into the ignition key cylinder (ignition switch off). Then turn the ignition switch to ON and off.


iii.

Within 30 seconds of turning the ignition switch OFF, perform the following operation 9 times: turn the ignition switch to ON and off.

CAUTION:

If the system cannot enter self-diagnostic mode, the system returns to normal mode.


HINT:
·

Turning the ignition switch ON after the above operations have been completed ends self-diagnostic mode.

·

Do not lock or unlock doors during self-diagnostic mode.




iv.
B220865E42
0.125,0.031 1.802,0.323 1.677,0.292 10 false Interior Light Output: 0.635,1.406 1.063,1.688 0.427,0.281 10 false ON 0.573,1.688 0.896,1.948 0.323,0.26 10 false OFF 1.552,2.167 1.917,2.5 0.365,0.333 10 false T1 2.146,2.167 2.604,2.604 0.458,0.438 10 false T2 1.979,2.604 3.427,3.042 1.448,0.438 10 false T1: 0.25 seconds 1.979,2.917 3.292,3.313 1.313,0.396 10 false T2: 0.5 seconds 1.802,2.167 2.125,2.51 0.323,0.344 10 false T1

Check that the system has switched to self-diagnostic mode by checking the interior light flash pattern.



Result:
Proceed to
NEXT



NEXT

5.CHECK BY SELF-DIAGNOSTIC MODE
5.CHECK BY SELF-DIAGNOSTIC MODE
a.

Inspect the diagnostic outputs when the door control transmitter assembly switch is pressed. The diagnostic outputs can be checked by the flash patterns of the interior lights.

B163380E76
0.115,0.063 1.604,0.323 1.49,0.26 10 false Interior Light Output: 0.292,1.344 1.979,1.625 1.688,0.281 10 false (Lock/Unlock Switch): 0.51,1.979 0.906,2.24 0.396,0.26 10 false ON 0.458,2.365 0.844,2.583 0.385,0.219 10 false OFF 4.125,0.563 6.51,0.938 2.385,0.375 10 false Unmatching Recognition Code: 4.26,1.156 4.583,1.385 0.323,0.229 10 false ON 4.208,1.552 4.74,1.906 0.531,0.354 10 false OFF 4.125,2.917 5.938,3.177 1.813,0.26 10 false No Diagnostic Output: 4.198,3.365 4.771,3.698 0.573,0.333 10 false OFF 1.25,2.802 1.563,3.01 0.313,0.208 10 false T1 1.76,2.802 2.146,3.063 0.385,0.26 10 false T2 4.938,2.031 6.604,2.344 1.667,0.313 10 false Wave is being received 0.594,3.469 2.979,3.813 2.385,0.344 10 false T1: 0.25 seconds (Interior Light) 0.594,3.896 2.969,4.25 2.375,0.354 10 false T2: 0.5 seconds (Interior Light) 0.292,1.031 1.542,1.281 1.25,0.25 10 false Normal Wave:


Result:
Result Proceed to
No diagnostic outputs. A
Unmatching recognition code is output. B
Normal wave (light flash pattern) is output. C



A

6.CHECK DOOR CONTROL RECEIVER (RESPONSE)

B

17.CHECK REGISTER RECOGNITION CODE

C

6.CHECK DOOR CONTROL RECEIVER (RESPONSE)
a.

Prepare the door control transmitter assembly from another vehicle.


b.

Press and hold down the door control transmitter assembly switch.


c.

Check that an unmatching recognition code is output.

Result:
Proceed to Proceed to
Unmatching recognition code is not output. A
Unmatching recognition code is output. B




A

7.CHECK WAVE ENVIRONMENT

B

14.INSPECT TRANSMITTER BATTERY (VOLTAGE)
7.CHECK WAVE ENVIRONMENT
a.

Bring the door control transmitter assembly near the door control receiver, and perform a wireless operation check.

HINT:
·

When the door control transmitter assembly is brought near the door control receiver, the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.

·

If the inspection result is that the problem only occurs in certain locations or times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.



Result:
Proceed to Proceed to
Wireless functions do not operate properly. A
Wireless functions operate properly. B




A

8.CHECK DOOR CONTROL RECEIVER (+B, GND)

B

END (AFFECTED BY WAVE INTERFERENCE)

8.CHECK DOOR CONTROL RECEIVER (+B, GND)
a.
B281165C08
1.49,0.146 1.906,0.375 0.417,0.229 2.594,1.406 2.208,1.406 true 1.219,1.417 0.833,1.417 true 0.219,0.146 0.396,0.292 0.177,0.146 10 false *a 0.469,1.333 1.073,1.573 0.604,0.24 10 false GND 2.667,1.323 3.063,1.646 0.396,0.323 10 false +B 1.594,0.177 2.427,0.51 0.833,0.333 10 false F47
*a Front view of wire harness connector
(to Door Control Receiver)


Disconnect the door control receiver connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F47-1 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F47-5 (+B) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

9.CHECK DOOR CONTROL RECEIVER (OUTPUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK DOOR CONTROL RECEIVER (OUTPUT)
a.

Connect the door control receiver connector.


b.
B281169C04
1.49,0.375 1.927,0.604 0.438,0.229 1.875,1.281 2.156,1.875 2.156,1.875 2.365,1.875 true 0.24,0.167 0.583,0.49 0.344,0.323 10 false *a 2.417,1.792 2.74,1.938 0.323,0.146 10 false RDA 1.594,0.417 1.969,0.594 0.375,0.177 10 false F47
*a Component with harness connected
(Door Control Receiver)


Measure the voltage and check for pulses according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F47-2 (RDA) - Body ground Ignition switch off, all doors closed and door control transmitter assembly switch not pressed 11 to 14 V
Ignition switch off, all doors closed and door control transmitter assembly switch pressed Pulse generation



Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (DOOR CONTROL RECEIVER - BODY COMPUTER)

NG

10.CHECK HARNESS AND CONNECTOR (DOOR CONTROL RECEIVER - BODY COMPUTER)
a.

Disconnect the F47 door control receiver connector.


b.

Disconnect the F52 body computer connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F47-2 (RDA) - F52-16 (RDA) Always Below 1 Ω
F47-3 (PRG) - F52-9 (PRG) Always Below 1 Ω
F47-2 (RDA) or F52-16 (RDA) - Body ground Always 10 kΩ or higher
F47-3 (PRG) or F52-9 (PRG) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

11.REPLACE DOOR CONTROL RECEIVER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.REPLACE DOOR CONTROL RECEIVER
a.

Temporarily replace the door control receiver with a new or known good one.

Click hereVehicle Interior>DOOR LOCK>DOOR CONTROL RECEIVER(for Sedan)>REMOVAL


Result:
Proceed to
NEXT



NEXT

12.CHECK REGISTER RECOGNITION CODE
12.CHECK REGISTER RECOGNITION CODE

Result:
Proceed to
NEXT



NEXT

13.CHECK DOOR CONTROL RECEIVER (OPERATION)
13.CHECK DOOR CONTROL RECEIVER (OPERATION)
a.

Check that the doors can be locked and unlocked by the door control transmitter assembly lock and unlock switches.

OK:

Doors can be locked and unlocked by the door control transmitter assembly.



Result:
Proceed to
OK
NG



OK

END (DOOR CONTROL RECEIVER WAS DEFECTIVE)

NG

14.INSPECT TRANSMITTER BATTERY (VOLTAGE)
a.

Inspect the transmitter battery capacity.

i.

Remove the transmitter battery from the door control transmitter module set sub-assembly that does not operate (Click hereVehicle Interior>DOOR LOCK>TRANSMITTER BATTERY(w/o Smart Entry and Start System)>REPLACEMENT). Attach a lead wire (0.6 mm (0.0236 in.) in diameter or less including wire sheath) with tape or equivalent to the negative (-) terminal.

NOTICE:

Do not wrap the lead wire around a terminal, wedge it between the terminals, or solder it. A terminal may be deformed or damaged, and the battery will not be able to be installed correctly.




b.
B343685C05
1.385,0.375 0.958,0.365 false 0.76,0.302 0.948,0.49 0.188,0.188 10 false *a
*a Lead Wire


Carefully pull the lead wire out from the position shown in the illustration and install the previously removed transmitter battery.

NOTICE:

When replacing the transmitter battery, before starting work, remove static electricity that has built up in the body by touching, for example, the vehicle to prevent the door control transmitter assembly from being damaged.



c.
B343686C01
1.969,0.667 1.563,0.688 false 2.021,0.594 2.333,0.792 0.313,0.198 10 false *a
*a GND


Check the transmitter battery voltage.

HINT:

Measure the transmitter battery voltage while pressing the lock or unlock switch on the door control transmitter module set sub-assembly.


Standard Voltage:
Item Content
Tester Connection Transmitter battery positive (+) - Transmitter battery negative (-)
Condition Ignition switch off, all doors closed and lock or unlock switch is pressed
Specified Condition 2.5 to 3.2 V



Result:
Proceed to
OK
NG



OK

REPLACE DOOR CONTROL TRANSMITTER MODULE SET SUB-ASSEMBLY

NG

15.REPLACE TRANSMITTER BATTERY
15.REPLACE TRANSMITTER BATTERY

Result:
Proceed to
NEXT



NEXT

16.CHECK BY SELF-DIAGNOSTIC MODE
16.CHECK BY SELF-DIAGNOSTIC MODE
a.

Inspect the diagnostic outputs when the door control transmitter assembly switch is pressed. The diagnostic outputs can be checked by the flash patterns of the interior lights.

B163380E76
0.115,0.063 1.604,0.323 1.49,0.26 10 false Interior Light Output: 0.292,1.344 1.979,1.625 1.688,0.281 10 false (Lock/Unlock Switch): 0.51,1.979 0.906,2.24 0.396,0.26 10 false ON 0.458,2.365 0.844,2.583 0.385,0.219 10 false OFF 4.125,0.563 6.51,0.938 2.385,0.375 10 false Unmatching Recognition Code: 4.26,1.156 4.583,1.385 0.323,0.229 10 false ON 4.208,1.552 4.74,1.906 0.531,0.354 10 false OFF 4.125,2.917 5.938,3.177 1.813,0.26 10 false No Diagnostic Output: 4.198,3.365 4.771,3.698 0.573,0.333 10 false OFF 1.25,2.802 1.563,3.01 0.313,0.208 10 false T1 1.76,2.802 2.146,3.063 0.385,0.26 10 false T2 4.938,2.031 6.604,2.344 1.667,0.313 10 false Wave is being received 0.594,3.469 2.979,3.813 2.385,0.344 10 false T1: 0.25 seconds (Interior Light) 0.594,3.896 2.969,4.25 2.375,0.354 10 false T2: 0.5 seconds (Interior Light) 0.292,1.031 1.542,1.281 1.25,0.25 10 false Normal Wave:


Result:
Result Proceed to
Normal wave (light flash pattern) is output. A
Unmatching recognition code is output. B
No diagnostic outputs.



A

END (TRANSMITTER BATTERY WAS DEFECTIVE)

B

REPLACE DOOR CONTROL TRANSMITTER MODULE SET SUB-ASSEMBLY

17.CHECK REGISTER RECOGNITION CODE
a.

Check that the system can be switched to rewrite mode or add mode, and that a recognition code can be registered.

Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM(w/o Smart Entry and Start System)>REGISTRATION

OK:

Recognition code can be registered.



Result:
Proceed to
OK
NG



OK

NG

REPLACE DOOR CONTROL TRANSMITTER MODULE SET SUB-ASSEMBLY