To control the cooling fan, the ECM turns on or off the FAN No. 1 relay and FAN No. 2 relay based on the engine coolant temperature, air conditioning switch, refrigerant pressure, engine speed and vehicle speed signals.
The ECM turns on or off the fan relays to switch the cooling fan motor circuit between the series circuit and parallel circuit, controlling the cooling fan motor speed in 2 steps.
Refer to System Diagram.
Click hereEngine / Hybrid System>2NZ-FE COOLING>COOLING FAN SYSTEM>SYSTEM DIAGRAM
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
| *1 | Engine Room Relay Block |
| *2 | FAN No. 1 Relay |
Remove the FAN No. 1 relay from the engine room relay block.
Check the voltage.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3 (FAN No. 1 relay) -Body ground | Always | 11 to 14 V |
Reinstall the FAN No. 1 relay to the engine room relay block.
| Result |
|---|
| OK |
| NG |
OK
NG
| *1 | Engine Room Relay Block |
| *2 | FAN No. 1 Relay |
| *3 | FAN No. 2 Relay |
Remove the FAN No. 1 relay and FAN No. 2 relay from the engine room relay block.
Turn the ignition switch to ON.
Check the voltage.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| 1 (FAN No. 1 relay) - Body ground | Ignition switch ON | 11 to 14 V |
| 1 (FAN No. 2 relay) - Body ground |
Reinstall the FAN No. 1 relay and FAN No. 2 relay to the engine room relay block.
| Result |
|---|
| OK |
| NG |
OK
NG
Inspect the FAN No. 1 relay.
Click hereEngine / Hybrid System>2NZ-FE COOLING>RELAY>ON-VEHICLE INSPECTION
| Result |
|---|
| OK |
| NG |
OK
NG
Inspect the FAN No. 2 relay.
Click hereEngine / Hybrid System>2NZ-FE COOLING>RELAY>ON-VEHICLE INSPECTION
| Result |
|---|
| OK |
| NG |
OK
NG
Inspect the cooling fan resistor.
Click hereEngine / Hybrid System>2NZ-FE COOLING>COOLING FAN RESISTOR>INSPECTION
| Result |
|---|
| OK |
| NG |
OK
NG
Remove the FAN No. 2 relay from the engine room relay block.
Check the resistance.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 5 (FAN No. 2 relay) - Body ground | Always | Below 1 Ω |
Reinstall the FAN No. 2 relay to the engine room relay block.
| Result |
|---|
| OK |
| NG |
OK
NG
Disconnect the A3 cooling fan resistor connector.
Check the resistance.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A3-1 (-) - Body ground | Always | Below 1 Ω |
Reconnect the A3 cooling fan resistor connector.
| Result |
|---|
| OK |
| NG |
OK
NG
Disconnect the A3 cooling fan resistor connector.
Remove the FAN No. 2 relay from the engine room relay block.
Check the resistance.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A3-2 (+) - 4 (FAN No. 2 relay) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A3-2 (+) or 4 (FAN No. 2 relay) - Body ground | Always | 10 kΩ or higher |
Reinstall the FAN No. 2 relay to the engine room relay block.
Reconnect the A3 cooling fan resistor connector.
| Result |
|---|
| OK |
| NG |
OK
NG
Inspect the cooling fan motor.
Click hereEngine / Hybrid System>2NZ-FE COOLING>COOLING FAN MOTOR>ON-VEHICLE INSPECTION
| Result |
|---|
| OK |
| NG |
OK
NG
Disconnect the A2 cooling fan motor connector.
Remove the FAN No. 1 relay from the engine room relay block.
Check the resistance.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A2-2 - 5 (FAN No. 1 relay) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A2-2 or 5 (FAN No. 1 relay) - Body ground | Always | 10 kΩ or higher |
Reinstall the FAN No. 1 relay to the engine room relay block.
Reconnect the A2 cooling fan motor connector.
| Result |
|---|
| OK |
| NG |
OK
NG
Disconnect the A2 cooling fan motor connector.
Remove the FAN No. 2 relay from the engine room relay block.
Check the resistance.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A2-1 - 3 (FAN No. 2 relay) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A2-1 or 3 (FAN No. 2 relay) - Body ground | Always | 10 kΩ or higher |
Reinstall the FAN No. 2 relay to the engine room relay block.
Reconnect the A2 cooling fan motor connector.
| Result |
|---|
| OK |
| NG |
OK
NG
Inspect the No. 1 pressure switch (for Cooling Fan Control).
| Result |
|---|
| OK |
| NG |
OK
NG
Disconnect the A24 No. 1 pressure switch connector.
Check the resistance.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A24-3 (-S) - Body ground | Always | Below 1 Ω |
Reconnect the A24 No. 1 pressure switch connector.
| Result |
|---|
| OK |
| NG |
OK
NG
Disconnect the A24 No. 1 pressure switch connector.
Remove the FAN No. 2 relay from the engine room relay block.
Check the resistance.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A24-2 (+S) - 2 (FAN No. 2 relay) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A24-2 (+S) or 2 (FAN No. 2 relay) - Body ground | Always | 10 kΩ or higher |
Reinstall the FAN No. 2 relay to the engine room relay block.
Reconnect the A24 No. 1 pressure switch connector.
| Result |
|---|
| OK |
| NG |
OK
NG
*1: for Automatic Transaxle
*2: for Manual Transaxle
Remove the FAN No. 1 relay and FAN No. 2 relay from the engine room relay block.
Disconnect the F83*1 and B30*2 ECM connector.
Check the resistance.
Measure the resistance according to the value(s) in the table below.
| Transaxle Type | Tester Connection | Condition | Specified Condition |
|---|---|---|---|
| Automatic Transaxle | 2 (FAN No. 1 relay) - F83-13 (FANL) | Always | Below 1 Ω |
| 2 (FAN No. 2 relay) - F83-14 (FANH) | |||
| Manual Transaxle | 2 (FAN No. 1 relay) - B30-15 (FANL) | ||
| 2 (FAN No. 2 relay) - B30-14 (FANH) |
| Transaxle Type | Tester Connection | Condition | Specified Condition |
|---|---|---|---|
| Automatic Transaxle | 2 (FAN No. 1 relay) or F83-13 (FANL) - Body ground | Always | 10 kΩ or higher |
| 2 (FAN No. 2 relay) or F83-14 (FANH) - Body ground | |||
| Manual Transaxle | 2 (FAN No. 1 relay) or B30-15 (FANL) - Body ground | ||
| 2 (FAN No. 2 relay) or B30-14 (FANH) - Body ground |
Reconnect the F83*1 and B30*2 ECM connector.
Reinstall the FAN No. 1 relay and FAN No. 2 relay to the engine room relay block.
| Result |
|---|
| OK |
| NG |
OK
NG