Home › Vehicle Interior › DOOR LOCK › FRONT DOOR LOCK(for TMMIN Made) › 2013.12–2018.01
RM30M0E _58 Vehicle Interior _017110 DOOR LOCK _0105857 FRONT DOOR LOCK(for TMMIN Made) A

DOOR LOCK  FRONT DOOR LOCK(for TMMIN Made)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 69750C 1.INSTALL FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY (w/ Power Door Lock)

a.

Engage the guide and install the front door inside locking cable assembly to the front door lock assembly.


b.
B359273

Engage the 3 claws and close the cover.


Hide 69750C 2.INSTALL FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY (w/o Power Door Lock)

a.

Engage the guide and install the front door inside locking cable assembly to the front door lock assembly.


Hide 69710B 3.INSTALL FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY (w/ Power Door Lock)

a.

Engage the guide and install the front door lock remote control cable assembly to the front door lock assembly.


Hide 69710B 4.INSTALL FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY (w/o Power Door Lock)

a.

Engage the guide and install the front door lock remote control cable assembly to the front door lock assembly.


Hide 69310 5.INSTALL FRONT DOOR LOCK ASSEMBLY (w/ Power Door Lock)

NOTICE:
·

When reusing the removed front door lock assembly, replace the door lock wiring harness seal on the connector with a new one.

·

Do not allow grease or dust to adhere to the door lock wiring harness seal surface of the connector.

·

Reusing the door lock wiring harness seal or using a damaged door lock wiring harness seal may cause water intrusion. This may result in a malfunction of the front door lock assembly.



a.

Apply MP grease to the sliding parts of the front door lock assembly.


b.

When reusing the front door lock assembly:

i.

Install a new door lock wiring harness seal to the front door lock assembly.



c.
B359269

Insert the front door lock open rod to the front door lock assembly.


d.

Make sure that the front door lock open rod is securely connected to the front door lock assembly.


e.

Using a T30 "TORX" socket wrench, install the front door lock assembly with the 3 screws.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


f.

Connect the connector.


Hide 69310 6.INSTALL FRONT DOOR LOCK ASSEMBLY (w/o Power Door Lock)

a.

Apply MP grease to the sliding parts of the front door lock assembly.


b.
B365424

Insert the front door lock open rod to the front door lock assembly.


c.

Make sure that the front door lock open rod is securely connected to the front door lock assembly.


d.

Using a T30 "TORX" socket wrench, install the front door lock assembly with the 3 screws.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


Hide 7.INSTALL FRONT DOOR OUTSIDE HANDLE COVER WITH LOCK CYLINDER ASSEMBLY (w/ Lock Cylinder)

Hide 67403F 8.INSTALL FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY

Hide 68141C 9.INSTALL FRONT DOOR GLASS RUN

Hide 68101 10.INSTALL FRONT DOOR GLASS SUB-ASSEMBLY

Hide 67831 11.INSTALL FRONT DOOR SERVICE HOLE COVER

Hide 68171B 12.INSTALL FRONT DOOR GLASS INNER WEATHERSTRIP

Hide 67601 13.INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY

Hide 74231 14.INSTALL FRONT ARMREST BASE UPPER PANEL (w/ Power Window)

Hide 74231 15.INSTALL FRONT ARMREST BASE UPPER PANEL (w/o Power Window)

Hide 69260 16.INSTALL FRONT DOOR WINDOW REGULATOR HANDLE ASSEMBLY (w/o Power Window)

Hide 67491A 17.INSTALL FRONT DOOR LOWER FRAME BRACKET GARNISH

Hide 18.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL (w/ Power Window)

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)

Hide 19.INITIALIZE POWER WINDOW CONTROL SYSTEM (for Driver Side with Power Window)

Hide 20.CHECK POWER WINDOW CONTROL SYSTEM (for Driver Side with Power Window)