Home › Drivetrain › U441E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE ASSEMBLY › 2014.03–2016.07
RM30M0E _52 Drivetrain _017088 U441E AUTOMATIC TRANSMISSION / TRANSAXLE _0090627 AUTOMATIC TRANSAXLE ASSEMBLY A

U441E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE ASSEMBLY  INSTALLATION  


PROCEDURE

Hide 33403M 1.INSTALL SPEEDOMETER DRIVEN HOLE COVER SUB-ASSEMBLY

a.

Apply a light coat of Toyota Genuine ATF Type T-IV to a new O-ring and install it to the speedometer driven hole cover sub-assembly.

NOTICE:

Do not twist the O-ring.



b.

Install the speedometer driven hole cover sub-assembly to the automatic transaxle assembly with the bolt.

Torque:
11.3 N*m (115 kgf*cm, 8 ft.*lbf)

NOTICE:

Make sure that the O-ring is not damaged or does not jump out of position during installation.



Hide 35013 2.INSTALL TRANSMISSION OIL FILLER TUBE SUB-ASSEMBLY

a.

Apply a light coat of Toyota Genuine ATF Type T-IV to a new O-ring and install it to the transmission oil filler tube sub-assembly.

NOTICE:

Do not twist the O-ring.



b.

Install the transmission oil filler tube sub-assembly to the automatic transaxle assembly with the bolt.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)

NOTICE:

Make sure that the O-ring is not damaged or does not jump out of position during installation.



c.

Connect the breather hose to the transmission oil filler tube sub-assembly.


Hide 35103 3.INSTALL TRANSMISSION OIL LEVEL DIPSTICK SUB-ASSEMBLY

a.

Install the transmission oil level dipstick sub-assembly into the transmission oil filler tube sub-assembly.


Hide 32924 4.INSTALL NO. 2 OIL COOLER TUBE CLAMP

a.

Temporarily install the outlet No. 1 oil cooler tube to the oil cooler tube union.


b.

Temporarily install the inlet No. 1 oil cooler tube to the oil cooler tube union.


c.

Install the No. 2 oil cooler tube clamp to the transmission oil filler tube sub-assembly with the bolt.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


Hide 32922 5.CONNECT OUTLET NO. 1 OIL COOLER TUBE

a.
C244619C01
1.479,1.583 1.646,1.76 0.167,0.177 10 true *a 2.302,2 2.49,2.177 0.188,0.177 10 false *b
*a Hold
*b Turn


Using a 14 mm union nut wrench, connect the outlet No. 1 oil cooler tube while holding the oil cooler tube union with a wrench.

Torque:
34 N*m (347 kgf*cm, 25 ft.*lbf)

NOTICE:

Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION



Hide 32921 6.CONNECT INLET NO. 1 OIL COOLER TUBE

a.
C244620C01
1.531,1.146 1.708,1.333 0.177,0.188 10 true *a 2.552,1.792 2.74,1.979 0.188,0.188 10 true *b
*a Hold
*b Turn


Using a 14 mm union nut wrench, connect the inlet No. 1 oil cooler tube while holding the oil cooler tube union with a wrench.

Torque:
34 N*m (347 kgf*cm, 25 ft.*lbf)

NOTICE:

Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION



Hide 33829 7.INSTALL TRANSMISSION CONTROL CABLE SUPPORT

a.

Install the transmission control cable support to the automatic transaxle assembly with the bolt.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 33823 8.INSTALL NO. 1 TRANSMISSION CONTROL CABLE BRACKET

a.

Install the No. 1 transmission control cable bracket to the automatic transaxle assembly with the 2 bolts.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 10.INSTALL TORQUE CONVERTER ASSEMBLY

a.
C293481C01
1.01,0.188 1.344,0.344 true 2.656,1.094 3.052,0.479 true 3.094,0.375 3.406,0.531 0.313,0.156 10 false *a 0.854,0.073 1.167,0.229 0.313,0.156 10 false *b
*a Key
*b Matchmark


Set the key at the top of the front oil pump drive gear and put a matchmark on the transaxle housing.


b.
C057914C01
1.792,0.344 2.198,0.188 true 1.271,1.823 1.729,1.542 true 2.24,0.083 2.552,0.24 0.313,0.156 10 false *a 1.094,1.75 1.406,1.906 0.313,0.156 10 false *b
*a Groove
*b Matchmark


Place a matchmark on the torque converter assembly so that the position of its groove is clearly indicated.


c.
C293482C01
1.083,0.646 0.677,0.281 0.677,0.281 1.083,0.469 true 2.469,1.208 2.135,1.052 2.135,1.052 2.469,0.875 true 1.99,0.969 2.302,1.125 0.313,0.156 10 false *1 0.5,0.167 0.813,0.323 0.313,0.156 10 false *a
*1 Front Oil Pump Oil Seal
*a Matchmark


Align the matchmark on the transaxle housing with the one on the torque converter assembly and engage the splines of the input shaft with the turbine runner splines.

NOTICE:
·

Install the torque converter assembly to the input shaft while keeping it horizontal.

·

Do not damage the front oil pump oil seal.




d.
C293483C01
0.688,0.302 1.083,0.469 true 2.479,1.219 2.146,1.052 2.146,1.052 2.469,0.875 true 0.75,1.833 1.083,1.375 true 2,0.969 2.313,1.125 0.313,0.156 10 false *1 0.5,0.177 0.813,0.333 0.313,0.156 10 false *a 0.667,1.844 0.979,2 0.313,0.156 10 false *a
*1 Front Oil Pump Oil Seal
*a Matchmark


Rotate the torque converter assembly approximately 180° and engage the splines of the stator shaft with the stator assembly.

NOTICE:
·

Install the torque converter assembly to the input shaft while keeping it horizontal.

·

Do not damage the front oil pump oil seal.




e.
C293484C01
1.083,0.646 0.677,0.281 0.677,0.281 1.083,0.479 true 2.469,1.229 2.135,1.052 2.135,1.052 2.458,0.885 true 1.99,0.969 2.302,1.125 0.313,0.156 10 false *1 0.5,0.177 0.813,0.333 0.313,0.156 10 false *a
*1 Front Oil Pump Oil Seal
*a Matchmark


Rotate the torque converter assembly approximately 180° again, align the matchmark on the torque converter assembly with the one on the transaxle housing and insert the groove of the torque converter assembly into the key of the front oil pump drive gear.

NOTICE:
·

Do not push the torque converter assembly excessively when rotating it.

·

Install the torque converter assembly to the input shaft while keeping it horizontal.

·

Do not damage the front oil pump oil seal.




f.

Clean the drive plate and torque converter assembly setting bolt holes.


g.
C283250C01
0.552,3 0.552,2.448 true 1,2.99 1,2.396 true 2.531,1.188 2.719,0.813 true 2.625,1.99 2.813,1.615 false 0.5,3.01 0.813,3.167 0.313,0.156 10 false *a 0.958,3.01 1.271,3.167 0.313,0.156 10 false *b 2.458,1.198 2.771,1.354 0.313,0.156 10 false *a 2.563,2.01 2.875,2.167 0.313,0.156 10 false *b 2.479,0.26 2.635,0.458 0.156,0.198 10 false A
*a Engine Surface
*b Drive Plate Surface


Using a vernier caliper and straightedge, measure dimension A between the automatic transaxle assembly contact surface of the engine assembly*a and the torque converter assembly contact surface of the drive plate*b.


h.
C200939E03
2.469,0.5 2.635,0.677 0.167,0.177 10 false B

Using a vernier caliper and straightedge, measure dimension B shown in the illustration and check that dimension B is more than dimension A, which was measured in the previous step.

Standard distance:

B = A + 1 mm (0.0394 in.) or more


NOTICE:
·

Make sure to deduct the thickness of the straightedge.

·

If the automatic transaxle assembly is installed to the engine assembly with the torque converter assembly not sufficiently inserted, the torque converter assembly may be damaged.

·

Do not include the thickness of the set block.




Hide 30500 11.INSTALL AUTOMATIC TRANSAXLE ASSEMBLY

a.
C202517C01
0.792,0.406 1.125,0.604 false 1.698,1.073 2.698,0.729 true 0.646,0.313 0.958,0.469 0.313,0.156 10 false *1 2.719,0.615 3.031,0.771 0.313,0.156 10 false *2
*1 Crankshaft
*2 Torque Converter Assembly Centerpiece
V100135

Clutch Spline Grease


Apply clutch spline grease to the surface of the crankshaft that contacts the torque converter assembly centerpiece.

Grease:

Toyota Genuine Clutch Spline Grease or equivalent


Maximum grease amount:

Approximately 1 g (0.0353 oz.)



b.
C283251C01
1.521,0.521 2.781,0.219 2.781,0.219 2.479,1.01 true 2.813,0.115 3.125,0.271 0.313,0.156 10 false *1
*1 Knock Pin


Confirm that the 2 knock pins are installed on the engine assembly and are not damaged.


c.
C286537N01
0.896,0.073 1.052,0.271 0.156,0.198 10 false A 2.365,0.031 2.521,0.229 0.156,0.198 10 false A 0.656,0.927 0.792,1.115 0.135,0.188 10 false B 0.906,1.75 1.042,1.938 0.135,0.188 10 true B 1.24,1.969 1.375,2.156 0.135,0.188 10 false B 2.177,1.969 2.313,2.156 0.135,0.188 10 false B 2.542,1.885 2.677,2.073 0.135,0.188 10 false B

Maintain the engine assembly and automatic transaxle assembly in a horizontal position, align the knock pins with each hole in the automatic transaxle assembly and install the automatic transaxle assembly to the engine assembly with the 7 bolts.

Torque:
29.5 N*m (301 kgf*cm, 22 ft.*lbf)

NOTICE:
·

Make sure that the wire harness or similar items are not pinched between the contact surfaces.

·

Do not forcibly pry on the automatic transaxle assembly.

·

When mounting the automatic transaxle assembly to the engine assembly, make sure to securely fit the knock pins into the knock holes.

·

Check that the torque converter assembly rotates.

·

When tightening the bolts, be sure that the contact surfaces of the engine assembly and automatic transaxle assembly are in close contact with one another.



HINT:
·

Bolt A: Install from automatic transaxle assembly side

·

Bolt B: Install from engine assembly side




d.
A192239C42
1.698,1.5 1.698,1.74 false 1.646,1.75 1.823,1.906 0.177,0.156 10 false *a
*a Adhesive


Clean and degrease the engine mounting bracket LH installation bolts and bolt holes.


e.

Apply adhesive to 2 or 3 threads on the ends of the 4 bolts.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent


NOTICE:

To prevent contamination by foreign matter, install immediately after applying adhesive.



f.
C282067C01
0.229,0.688 0.76,0.896 0.531,0.208 10 true 1 (*a), 5 1.844,0.698 2,0.896 0.156,0.198 10 true 2 1.885,1.719 2.042,1.917 0.156,0.198 10 true 4 0.625,1.688 0.74,1.875 0.115,0.188 10 true 3
*a Temporarily Tighten


Install the engine mounting bracket LH to the automatic transaxle assembly with the 4 bolts in the order shown in the illustration.

Torque:
64 N*m (653 kgf*cm, 47 ft.*lbf)


g.
C282066

Install the engine mounting bracket LH to the engine mounting insulator LH with the bolt and nut.

Torque:
52 N*m (530 kgf*cm, 38 ft.*lbf)

HINT:

Turn the bolt while holding the nut.



Hide 12364B 12.INSTALL NO. 2 ENGINE MOVING CONTROL ROD

a.
C286535C01
0.49,0.156 1.021,0.344 0.531,0.188 10 true 1 (*a), 4 0.854,0.646 0.99,0.833 0.135,0.188 10 true 2 2.427,1.323 2.563,1.51 0.135,0.188 10 true 3
*a Temporarily Tighten


Install the No. 2 engine moving control rod to the automatic transaxle assembly with the 3 bolts in the order shown in the illustration.

Torque:
45 N*m (459 kgf*cm, 33 ft.*lbf)


Hide 12321B 13.INSTALL DRIVE SHAFT HEAT INSULATOR SUB-ASSEMBLY

a.

Install the drive shaft heat insulator sub-assembly to the engine assembly with the bolt.

Torque:
17.6 N*m (179 kgf*cm, 13 ft.*lbf)


b.

Using a 12 mm deep socket wrench, install the nut.

Torque:
17.6 N*m (179 kgf*cm, 13 ft.*lbf)


Hide 51201 14.INSTALL FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY

Hide 32101A 15.INSTALL DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT

a.

Remove any adhesive remaining in the 6 drive plate and torque converter assembly setting bolts.


b.
A192239C42
1.698,1.5 1.698,1.74 false 1.646,1.75 1.823,1.906 0.177,0.156 10 false *a
*a Adhesive


Apply a few drops of adhesive to 2 or 3 threads at the tip of each of the 6 drive plate and torque converter assembly setting bolts.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent


NOTICE:

To prevent contamination by foreign matter, install immediately after applying adhesive.



c.
A107285E03
1.677,1.948 1.958,1.948 false 2,1.854 2.333,2.073 0.333,0.219 10 false SST

Turn the crankshaft to gain access to the installation locations of the 6 drive plate and torque converter assembly setting bolts and install each bolt while holding the crankshaft pulley with SST.

SST
09960-10010  (09962-01000, 09963-01000)

Torque:
28 N*m (286 kgf*cm, 21 ft.*lbf)

NOTICE:
·

First install the black-colored bolt, and then the remaining 5 silver-colored bolts.

·

Do not start the engine for at least 1 hour after installing the drive plate and torque converter assembly setting bolts.




Hide 11361J 16.INSTALL FLYWHEEL HOUSING UNDER COVER

a.

Install the flywheel housing under cover to the engine assembly.


Hide 32942 17.CONNECT OUTLET NO. 1 OIL COOLER HOSE

a.
C286533C01
1.021,2.271 1.333,2.427 0.313,0.156 10 false *a 1.667,3.198 1.979,3.354 0.313,0.156 10 false *b 2.042,1.781 2.198,1.979 0.156,0.198 10 true A
*a View A
*b Lower Side of Vehicle


Connect the outlet No. 1 oil cooler hose to the outlet No. 1 oil cooler tube and slide the hose clip to secure it as shown in the illustration.

NOTICE:

Perform the installation with the hose clip at the correct direction.



Hide 32941 18.CONNECT INLET NO. 1 OIL COOLER HOSE

a.
C286531C01
1.021,2.26 1.333,2.417 0.313,0.156 10 false *a 1.667,3.198 1.979,3.354 0.313,0.156 10 false *b 2.167,1.625 2.323,1.823 0.156,0.198 10 true A
*a View A
*b Lower Side of Vehicle


Connect the inlet No. 1 oil cooler hose to the inlet No. 1 oil cooler tube and slide the hose clip to secure it as shown in the illustration.

NOTICE:

Perform the installation with the hose clip at the correct direction.



Hide 28100 19.INSTALL STARTER ASSEMBLY

Hide 82121 21.CONNECT ENGINE WIRE

a.

Install the 3 wire harness clamp brackets to the automatic transaxle assembly with the 3 bolts.

Torque:
12.8 N*m (131 kgf*cm, 9 ft.*lbf)


b.

Engage the 6 clamps to install the engine wire.


c.

Connect the 3 connectors to the automatic transaxle assembly.


Hide 82123 22.CONNECT NO. 3 ENGINE WIRE

a.

Engage the 2 clamps to install the No. 3 engine wire to the engine mounting bracket LH.


b.

Connect the No. 3 engine wire to the automatic transaxle assembly with the bolt.

Torque:
25.5 N*m (260 kgf*cm, 19 ft.*lbf)


Hide 33820B 23.CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

NOTICE:

To prevent damage to the transmission control cable assembly and transmission floor shift assembly, connect the automatic transaxle assembly side of the transmission control cable assembly before connecting the transmission floor shift assembly side.


a.

Install the transmission control cable assembly to the transmission control cable support.


b.
C107759C01
1.333,1.969 1.5,2.146 0.167,0.177 10 true *a 0.781,1.094 0.958,1.271 0.177,0.177 10 true *b
*a P Position
*b N Position


Rotate the transmission control shaft lever counterclockwise until it stops, and then from that position rotate it clockwise by 2 notches to set it to the N position.


c.
C286333C01
0.552,0.875 0.323,0.688 true 0.167,0.573 0.375,0.76 0.208,0.188 10 false *a
*a Paint Mark


Install the transmission control cable assembly to the No. 1 transmission control cable bracket with a new clip.

NOTICE:

Make sure that the paint mark on the transmission control cable assembly is aligned with the slit in the No. 1 transmission control cable bracket before installing the clip.



d.

Connect the transmission control cable assembly to the transmission control shaft lever with the nut.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


e.
C286313

Confirm that the shift lever is in N, and then connect the end of the transmission control cable assembly to the transmission floor shift assembly.

NOTICE:
·

Securely install the end of the transmission control cable assembly to the transmission floor shift assembly.

·

Install the end of the transmission control cable assembly so that its adjustment lock section is on the driver side.




Hide 58910C 25.INSTALL REAR CONSOLE BOX ASSEMBLY (w/ Console Box Lid)

Hide 58910C 26.INSTALL REAR CONSOLE BOX ASSEMBLY (w/o Console Box Lid)

Hide 17801 31.INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

Hide 17735 32.INSTALL AIR CLEANER CAP WITH NO. 1 AIR CLEANER HOSE

Hide 23820 34.CONNECT FUEL VAPOR FEED HOSE ASSEMBLY

Hide 23827A 35.CONNECT NO. 2 FUEL VAPOR FEED HOSE

Hide 36.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 39.INSPECT FOR AUTOMATIC TRANSAXLE FLUID LEAK

Hide 51441C 41.INSTALL ENGINE UNDER COVER RH (w/o Metal Type Under Cover)

Hide 51442C 42.INSTALL ENGINE UNDER COVER LH (w/o Metal Type Under Cover)

Hide 51405A 43.INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY (w/ Metal Type Under Cover)

Hide 51451A 44.INSTALL CENTER ENGINE UNDER COVER (w/ Metal Type Under Cover)