Be sure that the ignition switch is off if you work near the electric cooling fans or radiator grille. With the ignition switch ON, the electric cooling fans may automatically start to run if the engine coolant temperature is high and/or the air conditioning is on.
81150
1.REMOVE HEADLIGHT ASSEMBLY LH (for Sedan)
81150
2.REMOVE HEADLIGHT ASSEMBLY RH (for Sedan)
Use the same procedure as for the LH side.
53141F
3.REMOVE RADIATOR COVER (for Hatchback)
53101
4.REMOVE RADIATOR GRILLE SUB-ASSEMBLY (for Hatchback)
89173
5.REMOVE FRONT AIRBAG SENSOR (w/ Airbag System)
6.DRAIN ENGINE COOLANT
53510
7.REMOVE HOOD LOCK ASSEMBLY (for Sedan)
53510
8.REMOVE HOOD LOCK ASSEMBLY (for Hatchback)
53215B
9.REMOVE HOOD LOCK SUPPORT (for Sedan)
Disengage the clamp to disconnect the wire harness from the hood lock support.
Remove the 2 bolts and hood lock support from the radiator support assembly.
53215B
10.REMOVE HOOD LOCK SUPPORT (for Hatchback)
Disengage the clamp to disconnect the wire harness from the hood lock support.
Remove the clip to separate the hood lock support from the front bumper assembly.
Remove the 2 bolts and hood lock support from the radiator support assembly.
88891H
11.REMOVE NO. 1 COOLER COVER (w/o Fan Shroud Ventilation Duct)
for Sedan:
Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>FRONT BUMPER(for Sedan)>DISASSEMBLY
for Hatchback:
Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>FRONT BUMPER(for Hatchback)>DISASSEMBLY
53216A
12.REMOVE UPPER RADIATOR SUPPORT
Disengage the clamp to separate the hood lock control cable assembly from the upper radiator support.
Disengage the 2 clamps to disconnect the wire harness from the upper radiator support.
Disconnect the low pitched horn assembly connector.
Remove the 4 bolts and upper radiator support from the radiator support assembly.
16750
13.REMOVE FAN SHROUD VENTILATION DUCT ASSEMBLY (w/ Fan Shroud Ventilation Duct)
Disengage the 2 claws and 2 guides to remove the fan shroud ventilation duct assembly from the radiator assembly.
14.DISCONNECT RADIATOR RESERVOIR TANK HOSE
Disconnect the radiator reservoir tank hose from the water filler sub-assembly.
16573B
15.DISCONNECT NO. 3 RADIATOR HOSE
Loosen the hose clip and disconnect the No. 3 radiator hose from the radiator assembly.
16572D
16.DISCONNECT NO. 2 RADIATOR HOSE
Loosen the hose clip and disconnect the No. 2 radiator hose from the radiator assembly.
32942
17.DISCONNECT OUTLET NO. 1 OIL COOLER HOSE (for Automatic Transaxle)
Loosen the hose clip and disconnect the outlet No. 1 oil cooler hose from the radiator assembly.
32941
18.DISCONNECT INLET NO. 1 OIL COOLER HOSE (for Automatic Transaxle)
Loosen the hose clip and disconnect the inlet No. 1 oil cooler hose from the radiator assembly.
16400
19.REMOVE RADIATOR ASSEMBLY (w/ Cooler System)
Disconnect the cooling fan motor connector.
Disengage the 3 clamps to disconnect the wire harness from the fan shroud.
Disengage the 2 claws and 2 guides to separate the cooler condenser assembly from the radiator assembly.
While tilting the cooler condenser assembly toward the front of the vehicle, separate the cooler condenser assembly from the radiator assembly.
Remove the radiator assembly together with fan shroud from the vehicle.
Do not apply excessive force to the cooler condenser assembly or piping when removing the radiator assembly.
16400
20.REMOVE RADIATOR ASSEMBLY (w/o Cooler System)
Disconnect the cooling fan motor connector.
Disengage the 3 clamps to disconnect the wire harness from the fan shroud.
Remove the radiator assembly together with fan shroud from the vehicle.
16711
21.REMOVE FAN SHROUD
Disengage the 2 claws and 2 guides to remove the fan shroud from the radiator assembly.
16561
22.REMOVE NO. 1 RADIATOR TO SUPPORT SEAL (w/ No. 1 Radiator to Support Seal)
This procedure is only performed when replacing the No. 1 radiator to support seal with a new one.
Remove the No. 1 radiator to support seal from the fan shroud.
16523A
23.REMOVE RADIATOR SUPPORT CUSHION
Remove the 2 radiator support cushions from the radiator assembly.
16535
24.REMOVE LOWER RADIATOR SUPPORT
Remove the 2 lower radiator supports from the radiator assembly.
25.REMOVE RADIATOR DRAIN COCK PLUG
Remove the radiator drain cock plug from the radiator assembly.
Replace the O-ring if it is damaged.
16561
26.REMOVE NO. 1 RADIATOR TO SUPPORT SEAL (w/ No. 1 Radiator to Support Seal)
This procedure is only performed when replacing the No. 1 radiator to support seal with a new one.
Remove the No. 1 radiator to support seal for upper side from the radiator assembly.
Remove the No. 1 radiator to support seal for lower side from the radiator assembly.