Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE BOOSTER(for RHD) › 2014.03–2016.04
RM30M0E _54 Brake _017099 BRAKE SYSTEM (OTHER) _0092765 BRAKE BOOSTER(for RHD) A

BRAKE SYSTEM (OTHER)  BRAKE BOOSTER(for RHD)  INSTALLATION  


PROCEDURE

Hide 44610 1.INSTALL BRAKE BOOSTER ASSEMBLY

a.

Install a new brake booster gasket to the brake booster assembly.


b.
C282666

Rotate the brake booster assembly as shown in the illustration and install it.

NOTICE:
·

Make sure the brake booster gasket does not fall off.

·

Do not damage the brake tubes.




c.

Temporarily install the brake booster assembly to the body with the 4 nuts.


d.
C282224E02
0.719,0.208 0.875,0.406 0.156,0.198 10 false 1 2.729,0.271 2.885,0.469 0.156,0.198 10 false 2 0.708,1.656 0.865,1.854 0.156,0.198 10 false 3 2.698,1.698 2.854,1.896 0.156,0.198 10 false 4

Tighten the 4 nuts in the order shown in the illustration.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)


e.

Install the brake tubes to the body with a new brake tube clamp.


Hide 47264D 2.INSTALL BRAKE MASTER CYLINDER PUSH ROD CLEVIS

a.

Install the clevis lock nut and brake master cylinder push rod clevis to the brake booster assembly.

HINT:

Tighten the clevis lock nut after adjusting the brake pedal height.



b.
C272700C02
0,0 3.427,0 false
V100145

Lithium Soap Base Glycol Grease


Apply lithium soap base glycol grease to the push rod pin.


c.

Install the brake master cylinder push rod clevis to the brake pedal sub-assembly with the push rod pin and a new clip.

NOTICE:

Install the push rod pin from the left side of the vehicle.



Hide 47101A 3.INSTALL BRAKE PEDAL RETURN SPRING

Hide 84340 5.INSTALL STOP LIGHT SWITCH ASSEMBLY

Hide 12305 6.INSTALL ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH

Hide 51441C 7.INSTALL ENGINE UNDER COVER RH (w/o Metal Type Under Cover)

Hide 51405A 8.INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY (w/ Metal Type Under Cover)

Hide 51451A 9.INSTALL CENTER ENGINE UNDER COVER (w/ Metal Type Under Cover)

Hide 17410 10.INSTALL FRONT EXHAUST PIPE ASSEMBLY

Hide 57533B 11.INSTALL FRONT FLOOR CENTER BRACE

Hide 58910C 12.INSTALL REAR CONSOLE BOX ASSEMBLY (w/ Console Box Lid)

Hide 58910C 13.INSTALL REAR CONSOLE BOX ASSEMBLY (w/o Console Box Lid)

Hide 44772 14.CONNECT CHECK VALVE TO CONNECTOR TUBE HOSE (for Automatic Transaxle)

a.

Connect the 2 check valve to connector tube hoses to the 2 brake vacuum check valve assemblies with the 2 hose clips.


Hide 44772 15.CONNECT CHECK VALVE TO CONNECTOR TUBE HOSE (for Manual Transaxle)

a.

Connect the check valve to connector tube hose to the brake vacuum check valve assembly with the hose clip.


Hide 47201 16.INSTALL BRAKE MASTER CYLINDER SUB-ASSEMBLY

Hide 17.INSPECT AND ADJUST BRAKE PEDAL

Hide 18.INSPECT FOR EXHAUST GAS LEAK