The door control receiver receives signals from the door control transmitter assembly and sends these signals to the body computer. The body computer then controls all doors by sending lock/unlock signals to each door, and sends hazard flasher signals to the combination meter assembly.
Inspect the fuses for circuits related to this system before performing the following procedure.
When replacing or inspecting the door control receiver and wire harness, do not change the position or length of the wire harness. If the wire harness is too close to the door control receiver, wireless function performance may be affected.
Check the power door lock operation.
Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK
Locked doors unlock
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Remove the unlock warning switch assembly.
Click hereVehicle Interior>DOOR LOCK>UNLOCK WARNING SWITCH>REMOVAL
Inspect the unlock warning switch assembly.
Click hereVehicle Interior>DOOR LOCK>UNLOCK WARNING SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the F27 unlock warning switch assembly connector.
Disconnect the F52 body computer connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F27-1 - F52-8 (KSW) | Always | Below 1 Ω |
| F27-2 - Body ground | Always | Below 1 Ω |
| F27-1 or F52-8 (KSW) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Switch to self-diagnostic mode by operating the ignition key cylinder.
Make sure the vehicle is in its initial condition. Then insert the key into the ignition key cylinder and remove it.
Within 5 seconds of removing the key, insert the key into the ignition key cylinder (ignition switch off). Then turn the ignition switch to ON and off.
Within 30 seconds of turning the ignition switch OFF, perform the following operation 9 times: turn the ignition switch to ON and off.
If the system cannot enter self-diagnostic mode, the system returns to normal mode.
Turning the ignition switch ON after the above operations have been completed ends self-diagnostic mode.
Do not lock or unlock doors during self-diagnostic mode.
Check that the system has switched to self-diagnostic mode by checking the interior light flash pattern.
| Proceed to |
| NEXT |
NEXT
Inspect the diagnostic outputs when the door control transmitter assembly switch is pressed. The diagnostic outputs can be checked by the flash patterns of the interior lights.
| Result | Proceed to |
|---|---|
| No diagnostic outputs | A |
| Unmatching recognition code is output | B |
| Normal wave (light flash pattern) is output | C |
A
B
C
Prepare the door control transmitter assembly from another vehicle.
Press and hold down the door control transmitter assembly switch.
Check that an unmatching recognition code is output.
| Result | Proceed to |
|---|---|
| Unmatching recognition code is not output | A |
| Unmatching recognition code is output | B |
A
B
Bring the door control transmitter assembly near the door control receiver, and perform a wireless operation check.
When the door control transmitter assembly is brought near the door control receiver, the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.
If the inspection result is that the problem only occurs in certain locations or times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.
| Proceed to | Proceed to |
|---|---|
| Wireless functions do not operate properly | A |
| Wireless functions operate properly | B |
A
B
| *a | Front view of wire harness connector
(to Door Control Receiver) |
Disconnect the door control receiver connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F47-1 (GND) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F47-5 (+B) - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the door control receiver connector.
| *a | Component with harness connected
(Door Control Receiver) |
Measure the voltage and check for pulses according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F47-2 (RDA) - Body ground | Ignition switch off, all doors closed and door control transmitter assembly switch not pressed | 11 to 14 V |
| Ignition switch off, all doors closed and door control transmitter assembly switch pressed | Pulse generation |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for Sedan) | B |
| NG (for Hatchback) | C |
A
B
C
Disconnect the F47 door control receiver connector.
Disconnect the F52 body computer connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F47-2 (RDA) - F52-16 (RDA) | Always | Below 1 Ω |
| F47-3 (PRG) - F52-9 (PRG) | Always | Below 1 Ω |
| F47-2 (RDA) or F52-16 (RDA) - Body ground | Always | 10 kΩ or higher |
| F47-3 (PRG) or F52-9 (PRG) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Temporarily replace the door control receiver with a new or known good one.
for Sedan: Click hereVehicle Interior>DOOR LOCK>DOOR CONTROL RECEIVER(for Sedan)>REMOVAL
for Hatchback: Click hereVehicle Interior>DOOR LOCK>DOOR CONTROL RECEIVER(for Hatchback)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Perform the Registration procedure.
| Proceed to |
|---|
| NEXT |
NEXT
Check that the doors can be locked and unlocked by the door control transmitter assembly lock and unlock switches.
Doors can be locked and unlocked by the door control transmitter assembly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the transmitter battery capacity.
Remove the transmitter battery from the door control transmitter module set sub-assembly that does not operate (Click hereVehicle Interior>DOOR LOCK>TRANSMITTER BATTERY(w/o Smart Entry and Start System)>REPLACEMENT). Attach a lead wire (0.6 mm (0.0236 in.) in diameter or less including wire sheath) with tape or equivalent to the negative (-) terminal.
Do not wrap the lead wire around a terminal, wedge it between the terminals, or solder it. A terminal may be deformed or damaged, and the battery will not be able to be installed correctly.
| *a | Lead Wire |
Carefully pull the lead wire out from the position shown in the illustration and install the previously removed transmitter battery.
When replacing the transmitter battery, before starting work, remove static electricity that has built up in the body by touching, for example, the vehicle to prevent the door control transmitter assembly from being damaged.
| *a | GND |
Check the transmitter battery voltage.
Measure the transmitter battery voltage while pressing the lock or unlock switch on the door control transmitter module set sub-assembly.
| Item | Content |
|---|---|
| Tester Connection | Transmitter battery positive (+) - Transmitter battery negative (-) |
| Condition | Ignition switch off, all doors closed and lock or unlock switch is pressed |
| Specified Condition | 2.5 to 3.2 V |
| Result | Proceed to |
|---|---|
| NG | A |
| OK | B |
A
B
Click hereVehicle Interior>DOOR LOCK>DOOR CONTROL TRANSMITTER(w/o Smart Entry and Start System)>REMOVAL
Replace the transmitter battery.
Click hereVehicle Interior>DOOR LOCK>TRANSMITTER BATTERY(w/o Smart Entry and Start System)>REPLACEMENT
| Proceed to |
|---|
| NEXT |
NEXT
Inspect the diagnostic outputs when the door control transmitter assembly switch is pressed. The diagnostic outputs can be checked by the flash patterns of the interior lights.
| Result | Proceed to |
|---|---|
| Normal wave (light flash pattern) is output | A |
| Unmatching recognition code is output | B |
| No diagnostic outputs |
A
B
Click hereVehicle Interior>DOOR LOCK>DOOR CONTROL TRANSMITTER(w/o Smart Entry and Start System)>REMOVAL
Check that the system can be switched to rewrite mode or add mode, and that a recognition code can be registered.
Recognition code can be registered.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Interior>DOOR LOCK>DOOR CONTROL TRANSMITTER(w/o Smart Entry and Start System)>REMOVAL