Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM › 2016.04–2017.10
RM30M0E _54 Brake _017098 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0090184 ANTI-LOCK BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  C1425  Open in Stop Light Switch Circuit  


DESCRIPTION

The skid control ECU (brake actuator assembly) detects the brake operating conditions through a signal transmitted by the stop light switch.

The skid control ECU (brake actuator assembly) has an open detection circuit, which outputs this DTC when detecting an open in the stop light input line or the ground line of the stop light circuit with the stop light switch off (brake pedal not depressed).

DTC No. Detection Item DTC Detection Condition Trouble Area
C1425 Open in Stop Light Switch Circuit When IG1 terminal voltage is between 9.5 and 17.4 V, an open stop light switch circuit (A to B, A to body ground) continues for 3 seconds or more.
·

Stop light switch circuit

·

Skid control ECU (Brake actuator assembly)



WIRING DIAGRAM

C353734E01
3.906,0.469 4.073,0.635 0.167,0.167 5.302,0.167 5.469,0.333 0.167,0.167 0.583,0.604 1.552,0.833 0.969,0.229 10 false from Battery 1.885,0.771 2.302,1 0.417,0.229 10 false STOP 2.385,0.521 2.552,0.688 0.167,0.167 10 false 2 3.635,0.521 3.802,0.688 0.167,0.167 10 false 1 2.552,0.542 2.719,0.708 0.167,0.167 10 false B 3.469,0.542 3.635,0.708 0.167,0.167 10 false L 3.938,0.469 4.104,0.635 0.167,0.167 10 false A 5.344,0.167 5.51,0.333 0.167,0.167 10 false B 4.167,1.333 5,1.583 0.833,0.25 10 false Stop Light 4.948,0.438 5.198,0.604 0.25,0.167 10 false 28 5.271,0.438 5.521,0.604 0.25,0.167 10 false 28 4.917,0.625 5.25,0.792 0.333,0.167 10 false A35 5.229,0.625 5.563,0.792 0.333,0.167 10 false A47 4.948,0.802 5.198,0.969 0.25,0.167 10 false *1 5.292,0.802 5.542,0.969 0.25,0.167 10 false *2 5.552,0.521 5.885,0.688 0.333,0.167 10 false STP 5.958,0.438 6.583,1.417 0.625,0.979 10 false Open Detection Circuit 5.49,1.833 7.052,2.26 1.563,0.427 10 false Skid Control ECU (Brake Actuator Assembly) 0.25,2 3.917,2.25 3.667,0.25 10 false *1: except LHD with Continuously Variable Transaxle 0.25,2.333 3.917,2.583 3.667,0.25 10 false *2: for LHD with Continuously Variable Transaxle 2.5,1.167 3.625,1.615 1.125,0.448 10 false Stop Light Switch Assembly 2.5,1 2.833,1.25 0.333,0.25 10 false A21

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

When replacing the skid control ECU (brake actuator assembly), perform reset memory, deceleration sensor zero point calibration and CVT oil pressure calibration (for CVT).




PROCEDURE

1.CHECK STOP LIGHT OPERATION
a.

Check that the stop lights come on when the brake pedal is depressed, and go off when the brake pedal is released.


OK:
Condition Illumination Condition
Brake pedal depressed ON
Brake pedal released OFF


Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS (STOP LIGHT SWITCH ASSEMBLY)

NG

2.READ VALUE USING GTS (STOP LIGHT SWITCH ASSEMBLY)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.


e.

According to the display on the GTS, read the Data List.

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stop Light SW Stop light switch OFF or ON OFF: Brake pedal released
ON: Brake pedal depressed
-
Chassis > ABS/VSC/TRC > Data List
Tester Display
Stop Light SW
50003 105 37

f.

Check that the stop light switch display observed on the GTS changes according to brake pedal operation.

OK:

The GTS displays ON or OFF according to brake pedal operation.



Result:
Proceed to
OK
NG



OK

3.RECONFIRM DTC

NG

4.CHECK HARNESS AND CONNECTOR (STP TERMINAL)
3.RECONFIRM DTC
a.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

Start the engine.


c.

Depress the brake pedal several times to test the stop light circuit.


d.

Check if the same DTC is recorded.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
DTC (C1425) is not output A
DTC (C1425) is output B


HINT:

If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE



A

B

4.CHECK HARNESS AND CONNECTOR (STP TERMINAL)
a.
C353731C03
1.583,0.25 2,0.5 0.417,0.25 1.583,2.417 2,2.667 0.417,0.25 1.167,2.333 1.594,1.594 true 1.167,4.5 1.594,3.771 true 1.667,0.302 2.125,0.5 0.458,0.198 10 false A35 1.667,2.469 2.125,2.667 0.458,0.198 10 false A47 0.167,0.135 0.479,0.333 0.313,0.198 10 false *a 2.083,0.292 2.417,0.458 0.333,0.167 10 false *A 2.083,2.469 2.417,2.635 0.333,0.167 10 false *B 0.875,4.417 1.333,4.615 0.458,0.198 10 false STP 0.875,2.25 1.333,2.448 0.458,0.198 10 false STP
*A except LHD with Continuously Variable Transaxle
*B for LHD with Continuously Variable Transaxle
*a Front view of wire harness connector (to Skid Control ECU (Brake Actuator Assembly))


Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


c.

Disconnect the skid control ECU (brake actuator assembly) connector.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
except LHD with Continuously Variable Transaxle
Tester Connection Switch Condition Specified Condition
A35-28 (STP) - Body ground Stop light switch on (Brake pedal depressed) 7.5 to 14 V
A35-28 (STP) - Body ground Stop light switch off (Brake pedal released) Below 1.5 V

for LHD with Continuously Variable Transaxle
Tester Connection Switch Condition Specified Condition
A47-28 (STP) - Body ground Stop light switch on (Brake pedal depressed) 7.5 to 14 V
A47-28 (STP) - Body ground Stop light switch off (Brake pedal released) Below 1.5 V



e.

Reconnect the skid control ECU (brake actuator assembly) connector.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STP CIRCUIT)