Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM › 2016.04–2016.10
RM30M0E _54 Brake _017098 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0090184 ANTI-LOCK BRAKE SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  ABS Warning Light Remains ON  


DESCRIPTION

The skid control ECU (brake actuator assembly) is connected to the combination meter assembly via CAN communication.

If any of the following is detected, the ABS warning light remains on:

·

The skid control ECU (brake actuator assembly) connector is disconnected from the brake actuator assembly.

·

There is a malfunction in the skid control ECU (brake actuator assembly) internal circuit.

·

There is an open in the harness between the combination meter assembly and the skid control ECU (brake actuator assembly).

·

The ABS control system is defective.


HINT:

In some cases, the GTS cannot be used when the skid control ECU (brake actuator assembly) is abnormal.


WIRING DIAGRAM

C353737E01
1.083,3.333 2.917,3.5 1.833,0.167 10 false : CAN Communication Line 0.583,2.75 2.583,2.917 2,0.167 10 false Combination Meter Assembly 1.75,2.417 2,2.583 0.25,0.167 10 false IG 1.031,1.833 1.448,2 0.417,0.167 10 false ABS 1.833,0.667 2.167,1.083 0.333,0.417 10 false CAN I/F 0.885,1.25 1.302,1.417 0.417,0.167 10 false CPU 5.833,1.5 6.25,1.667 0.417,0.167 10 false GND1 5.833,2.302 6.167,2.469 0.333,0.167 10 false IG1 5.188,2.302 5.521,2.469 0.333,0.167 10 false A35 5.51,2.302 5.844,2.469 0.333,0.167 10 false A47 5.51,1.51 5.844,1.677 0.333,0.167 10 false A47 5.188,1.51 5.521,1.677 0.333,0.167 10 false A35 5.25,1.323 5.5,1.49 0.25,0.167 10 false 1 5.573,1.323 5.823,1.49 0.25,0.167 10 false 1 5.552,2.115 5.802,2.281 0.25,0.167 10 false 34 5.229,2.115 5.479,2.281 0.25,0.167 10 false 34 4.333,2.448 5,2.615 0.667,0.167 10 false IG1 NO.2 3,2.313 4,2.479 1,0.167 10 false from IG Circuit 5.479,2.75 7.156,3.167 1.677,0.417 10 false Skid Control ECU (Brake Actuator Assembly) 5.229,1.698 5.479,1.865 0.25,0.167 10 false *1 5.229,2.49 5.479,2.656 0.25,0.167 10 false *1 5.552,1.698 5.802,1.865 0.25,0.167 10 false *2 5.552,2.49 5.802,2.656 0.25,0.167 10 false *2 3.49,3.25 6.917,3.5 3.427,0.25 10 false *1: except LHD with Continuously Variable Transaxle 3.5,3.5 6.927,3.75 3.427,0.25 10 false *2: for LHD with Continuously Variable Transaxle

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

When replacing the skid control ECU (brake actuator assembly), perform reset memory, deceleration sensor zero point calibration and CVT oil pressure calibration (for CVT).




PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if CAN communication system DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM


Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

2.CHECK IF BRAKE ACTUATOR ASSEMBLY CONNECTOR IS SECURELY CONNECTED

B

2.CHECK IF BRAKE ACTUATOR ASSEMBLY CONNECTOR IS SECURELY CONNECTED
a.

Check if the skid control ECU (brake actuator assembly) connector is securely connected.

OK:

The connector is securely connected.



Result:
Proceed to
OK
NG



OK

3.CHECK BATTERY

NG

CONNECT CONNECTOR TO ACTUATOR CORRECTLY

3.CHECK BATTERY
a.

Check the battery voltage.

Standard voltage:

11 to 14 V



Result:
Result Proceed to
OK A
NG (for 1NZ-FE) B
NG (for 2NZ-FE) C
NG (for 1NR-FE) D
NG (for 2NR-FE) E



A

4.CHECK HARNESS AND CONNECTOR (IG1 TERMINAL)

B

C

D

E

4.CHECK HARNESS AND CONNECTOR (IG1 TERMINAL)
a.
C353731C01
1.583,0.25 2,0.5 0.417,0.25 1.583,2.417 2,2.667 0.417,0.25 2.583,2.333 2.177,1.594 true 2.583,4.5 2.177,3.771 true 1.667,0.302 2.125,0.5 0.458,0.198 10 false A35 1.667,2.469 2.125,2.667 0.458,0.198 10 false A47 0.167,0.135 0.479,0.333 0.313,0.198 10 false *a 2.083,0.292 2.417,0.458 0.333,0.167 10 false *A 2.083,2.469 2.417,2.635 0.333,0.167 10 false *B 2.667,4.417 3.125,4.615 0.458,0.198 10 false IG1 2.667,2.25 3.125,2.448 0.458,0.198 10 false IG1
*A except LHD with Continuously Variable Transaxle
*B for LHD with Continuously Variable Transaxle
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Disconnect the skid control ECU (brake actuator assembly) connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
except LHD with Continuously Variable Transaxle
Tester Connection Switch Condition Specified Condition
A35-34 (IG1) - Body ground Ignition switch ON 11 to 14 V

for LHD with Continuously Variable Transaxle
Tester Connection Switch Condition Specified Condition
A47-34 (IG1) - Body ground Ignition switch ON 11 to 14 V



d.

Turn the ignition switch off.


Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (IG1 CIRCUIT)

5.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)
a.
C353731C02
1.583,0.25 2,0.5 0.417,0.25 1.583,2.417 2,2.667 0.417,0.25 0.75,0.5 1,1.177 true 0.75,2.667 1,3.385 true 1.667,0.302 2.125,0.5 0.458,0.198 10 false A35 1.667,2.469 2.125,2.667 0.458,0.198 10 false A47 0.167,0.135 0.479,0.333 0.313,0.198 10 false *a 2.083,0.292 2.417,0.458 0.333,0.167 10 false *A 2.083,2.469 2.417,2.635 0.333,0.167 10 false *B 0.542,0.302 1,0.5 0.458,0.198 10 false GND1 0.542,2.469 1,2.667 0.458,0.198 10 false GND1
*A except LHD with Continuously Variable Transaxle
*B for LHD with Continuously Variable Transaxle
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
except LHD with Continuously Variable Transaxle
Tester Connection Condition Specified Condition
A35-1 (GND1) - Body ground Always Below 1 Ω

for LHD with Continuously Variable Transaxle
Tester Connection Condition Specified Condition
A47-1 (GND1) - Body ground Always Below 1 Ω



b.

Reconnect the skid control ECU (brake actuator assembly) connector.


Result:
Proceed to
OK
NG



OK

6.READ VALUE USING GTS (ABS WARNING LIGHT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND1 CIRCUIT)

6.READ VALUE USING GTS (ABS WARNING LIGHT)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.


e.

According to the display on the GTS, read the Data List.

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
ABS Warning Light ABS warning light OFF or ON OFF: Warning light off
ON: Warning light on
-
Chassis > ABS/VSC/TRC > Data List
Tester Display
ABS Warning Light
50003 105 51

f.

Check the GTS display condition of the ABS warning light.


Result:
Result Proceed to
Display of the Data List remains OFF A
Display of the Data List remains ON B


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE



A

B