Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2016.04–2017.10
RM30M0E _54 Brake _017098 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0256246 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1422  Master Cylinder Pressure Sensor Zero Point High Malfunction  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area
C1422 Master Cylinder Pressure Sensor Zero Point High Malfunction When the stop light switch is OFF, the PMC terminal voltage is more than 0.86 V for 5 seconds or more.
·

Stop light switch assembly

·

Wire harness or connector

·

Skid control ECU (Brake actuator assembly)

·

Brake actuator assembly (Master cylinder pressure sensor)



CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK DTC
a.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Drive the vehicle at a speed of 40 km/h (25 mph) or more and perform braking test (decelerate the vehicle by depressing the brake pedal).


e.

Check for DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Result Proceed to
DTC C1422 is output A
DTCs C1422 and C1425 are output B




A

2.READ VALUE USING GTS (STOP LIGHT SW)

B

2.READ VALUE USING GTS (STOP LIGHT SW)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.


e.

In accordance with the display on the GTS, read the Data List.


Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stop Light SW Stop light switch assembly ON or OFF OFF: Brake pedal released
ON: Brake pedal depressed
-
Chassis > ABS/VSC/TRC > Data List
Tester Display
Stop Light SW
50003 105 37
f.

Check that the stop light switch assembly condition observed on the GTS changes according to brake pedal operation.


OK:

The GTS displays ON or OFF according to brake pedal operation.


Result:
Proceed to
OK
NG



OK

3.READ VALUE USING GTS (MASTER CYLINDER SENSOR)

NG

5.CHECK BRAKE PEDAL AND STOP LIGHT SWITCH ASSEMBLY INSTALLATION
3.READ VALUE USING GTS (MASTER CYLINDER SENSOR)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.


e.

In accordance with the display on the GTS, read the Data List.


Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Master Cylinder Sensor Master cylinder pressure sensor reading Min.: 0.00 V, Max.: 5.00 V Brake pedal released: 0.30 to 0.80 V Reading increases when brake pedal is depressed
Chassis > ABS/VSC/TRC > Data List
Tester Display
Master Cylinder Sensor
50003 105 9
f.

Check that the brake fluid pressure value of the master cylinder pressure sensor observed on the GTS changes when the brake pedal is depressed.

OK:

When the pedal is depressed, the voltage displayed on the GTS increases.



Result:
Proceed to
OK
NG



OK

4.RECONFIRM DTC

NG

4.RECONFIRM DTC

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105
b.

Turn the ignition switch off.


c.

Start the engine.


d.

Drive the vehicle at a speed of 40 km/h (25 mph) or more and perform braking test (decelerate the vehicle by depressing the brake pedal).



Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Result Proceed to
DTC C1422 is not output A
DTC C1422 is output B



A

B

5.CHECK BRAKE PEDAL AND STOP LIGHT SWITCH ASSEMBLY INSTALLATION
a.

Turn the ignition switch off.


b.

Check the brake pedal height and stop light switch assembly installation.

Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE PEDAL(for RHD)>ADJUSTMENT

OK:

The brake pedal height and stop light switch assembly installation are normal.



Result:
Proceed to
OK
NG



OK

6.INSPECT STOP LIGHT SWITCH ASSEMBLY

NG

ADJUST BRAKE PEDAL OR STOP LIGHT SWITCH ASSEMBLY

6.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.

Remove the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>REMOVAL


b.

Inspect the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSPECTION

Result:
Proceed to
OK
NG




OK

7.CHECK HARNESS AND CONNECTOR (STP TERMINAL)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

7.CHECK HARNESS AND CONNECTOR (STP TERMINAL)
a.
C349101C05
1.448,2.417 1.948,2.667 0.5,0.25 1.448,0.396 1.948,0.646 0.5,0.25 0.5,3.51 1.313,3.344 true 0.5,1.49 1.313,1.323 true 0.333,0.25 0.813,0.573 0.479,0.323 12 false *A 0.333,2.333 0.896,2.573 0.563,0.24 12 false *B 0.094,0.073 0.406,0.229 0.313,0.156 10 false *a 1.583,0.427 1.979,0.667 0.396,0.24 10 false A48 1.583,2.448 1.979,2.688 0.396,0.24 10 false A49 0.177,1.406 0.573,1.646 0.396,0.24 10 false STP 0.177,3.417 0.573,3.656 0.396,0.24 10 false STP
*A for Manual Transaxle
*B for Continuously Variable Transaxle
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


c.

Disconnect the skid control ECU (brake actuator assembly) connector.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for Manual Transaxle
Tester Connection Switch Condition Specified Condition
A48-2 (STP) - Body ground Stop light switch assembly on (Brake pedal depressed) 8 to 14 V
A48-2 (STP) - Body ground Stop light switch assembly off (Brake pedal released) Below 1.5 V

for Continuously Variable Transaxle
Tester Connection Switch Condition Specified Condition
A49-2 (STP) - Body ground Stop light switch assembly on (Brake pedal depressed) 8 to 14 V
A49-2 (STP) - Body ground Stop light switch assembly off (Brake pedal released) Below 1.5 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STP CIRCUIT)