While the engine is being cranked, current flows from terminal ST2 of the ignition or starter switch assembly*1 or terminal STAR of the certification ECU (smart key ECU assembly)*2 to the park/neutral position switch*3 or clutch start switch assembly*4 and to terminal STA of the ECM (STA signal).
*1: w/o Smart Entry and Start System
*2: w/ Smart Entry and Start System
*3: for CVT
*4: for Manual Transaxle
Refer to DTC P0617.
Click hereEngine / Hybrid System>1NR-FE ENGINE CONTROL>SFI SYSTEM>P0617
Inspect the fuses for circuits related to this system before performing the following procedure.
After turning ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
Check if the engine can be cranked.
| Result | Proceed to |
|---|---|
| Engine cannot be cranked | A |
| Engine can be cranked | B |
A
B
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.
| Tester Display |
|---|
| Starter Signal |
Check the value displayed on the GTS when the ignition switch is turned to the ON and START positions.
| Switch Position | Starter Signal |
|---|---|
| ON | OFF |
| START | ON |
| Result | Proceed to |
|---|---|
| NG (for CVT) | A |
| NG (for Manual Transaxle) | B |
| OK | C |
A
B
C
Inspect the park/neutral position switch.
Click hereDrivetrain>K411 CVT>PARK / NEUTRAL POSITION SWITCH>INSPECTION
| Result | Proceed to |
|---|---|
| OK (w/ Smart Entry and Start System) | A |
| OK (w/o Smart Entry and Start System) | B |
| NG | C |
A
B
C
Disconnect the F44 certification ECU (smart key ECU assembly) connector.
Disconnect the B19 park/neutral position switch connector.
Disconnect the B47 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F44-16 (STAR) - B19-4 (B) | Always | Below 1 Ω |
| F44-16 (STAR) - B47-15 (NSW) | Always | Below 1 Ω |
| F44-16 (STAR), B19-4 (B) or B47-15 (NSW) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the B19 park/neutral position switch connector.
Remove the starter relay assembly from the engine room relay block.
Disconnect the B47 ECM connector.
Disconnect the F44 certification ECU (smart key ECU assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B47-17 (STA) - B19-9 (L) | Always | Below 1 Ω |
| B47-17 (STA) - 2 (Starter relay assembly holder) | Always | Below 1 Ω |
| B47-17 (STA) - F44-37 (STA) | Always | Below 1 Ω |
| B19-9 (L), 2 (Starter relay assembly holder), B47-17 (STA) or F44-37 (STA) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the ignition or starter switch assembly.
Click hereEngine / Hybrid System>1NR-FE STARTING>IGNITION SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the F7 ignition or starter switch assembly connector.
Disconnect the B19 park/neutral position switch connector.
Disconnect the B47 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F7-7 (ST2) - B19-4 (B) | Always | Below 1 Ω |
| F7-7 (ST2) - B47-15 (NSW) | Always | Below 1 Ω |
| F7-7 (ST2), B19-4 (B) or B47-15 (NSW) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the B19 park/neutral position switch connector.
Remove the starter relay assembly from the engine room relay block.
Disconnect the B47 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B19-9 (L) - B47-17 (STA) | Always | Below 1 Ω |
| 2 (Starter relay assembly holder) - B47-17 (STA) | Always | Below 1 Ω |
| B19-9 (L), 2 (Starter relay assembly holder) or B47-15 (STA) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the clutch start switch assembly.
| Result | Proceed to |
|---|---|
| OK (w/ Smart Entry and Start System) | A |
| OK (w/o Smart Entry and Start System) | B |
| NG | C |
A
B
C
Disconnect the F44 certification ECU (smart key ECU assembly) connector.
Disconnect the A28 clutch start switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F44-16 (STAR) - A28-2 | Always | Below 1 Ω |
| F44-16 (STAR), A28-2 - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the A28 clutch start switch assembly connector.
Remove the starter relay assembly from the engine room relay block.
Disconnect the B47 ECM connector.
Disconnect the F44 certification ECU (smart key ECU assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B47-17 (STA) - A28-1 | Always | Below 1 Ω |
| B47-17 (STA) - 2 (Starter relay assembly holder) | Always | Below 1 Ω |
| B47-17 (STA) - F44-37 (STA) | Always | Below 1 Ω |
| A28-1, 2 (Starter relay assembly holder), B47-17 (STA) or F44-37 (STA) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the ignition or starter switch assembly.
Click hereEngine / Hybrid System>1NR-FE STARTING>IGNITION SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the F7 ignition or starter switch assembly connector.
Disconnect the A28 clutch start switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F7-7 (ST2) - A28-2 | Always | Below 1 Ω |
| F7-7 (ST2), A28-2 - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the A28 clutch start switch assembly connector.
Remove the starter relay assembly from the engine room relay block.
Disconnect the B47 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A28-1 - B47-17 (STA) | Always | Below 1 Ω |
| 2 (Starter relay assembly holder) - B47-17 (STA) | Always | Below 1 Ω |
| A28-1, 2 (Starter relay assembly holder) or B47-17 (STA) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the starter relay assembly.
Click hereEngine / Hybrid System>1NR-FE STARTING>RELAY>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the starter assembly.
Click hereEngine / Hybrid System>1NR-FE STARTING>STARTER>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the starter relay assembly from the engine room relay block.
Disconnect the B15 starter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3 (Starter relay assembly holder) - B15-1 | Always | Below 1 Ω |
| 3 (Starter relay assembly holder) or B15-1 - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the cable from the negative (-) battery terminal.
Disconnect the cable from the positive (+) battery terminal.
Disconnect the B28 starter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Positive (+) battery terminal - B28-1 | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Engine Room Relay Block |
| *2 | Relay Holder (Starter Relay Assembly) |
Remove the starter relay assembly from the engine room relay block.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 5 (Starter relay assembly holder) - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the starter relay assembly from the engine room relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 (Starter relay assembly holder) - Body ground | Always | Below 1 Ω |
| Result | Proceed to |
|---|---|
| OK (for CVT) | A |
| OK (for Manual Transaxle) | B |
| NG | C |
A
B
C
Remove the starter relay assembly from the engine room relay block.
Disconnect the B19 park/neutral position switch connector.
Disconnect the B47 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2 (Starter relay assembly holder) - B19-9 (L) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the starter relay assembly from the engine room relay block.
Disconnect the A28 clutch start switch assembly connector.
Disconnect the B47 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2 (Starter relay assembly holder) - A28-1 | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.
| Tester Display |
|---|
| Starter Signal |
Check the value displayed on the GTS when the ignition switch is turned to the ON and START positions.
| Switch Position | Starter Signal |
|---|---|
| ON | OFF |
| START | ON |
| Proceed to |
|---|
| OK |
| NG |
OK
NG