Home › Engine / Hybrid System › 1NR-FE COOLING › COOLING FAN SYSTEM › from 2016.04
RM30M0E _51 Engine / Hybrid System _053564 1NR-FE COOLING _0259956 COOLING FAN SYSTEM J

1NR-FE COOLING  COOLING FAN SYSTEM  Cooling Fan Circuit  


TECHNICAL DESCRIPTION

To control the cooling fan, the ECM turns on or off the FAN No. 1 relay and FAN No. 2 relay based on the engine coolant temperature, air conditioning switch (w/ air conditioning system), refrigerant pressure, engine speed and vehicle speed signals.

The ECM turns on or off the fan relays to switch the cooling fan motor circuit between the series circuit and parallel circuit, controlling the cooling fan motor speed in 2 steps.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.INSPECT ENGINE ROOM RELAY BLOCK (FAN NO. 1 RELAY)
a.
A312092C01
0.115,0.104 0.427,0.26 0.313,0.156 10 false *1 0.198,1.813 0.51,1.969 0.313,0.156 10 false *2
*1 Engine Room Relay Block
*2 FAN No. 1 Relay


Remove the FAN No. 1 relay from the engine room relay block.


b.

Check the voltage.

i.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
3 (FAN No. 1 relay) - Body ground Always 11 to 14 V




c.

Reinstall the FAN No. 1 relay to the engine room relay block.

Result:
Result
OK
NG




OK

2.INSPECT ENGINE ROOM RELAY BLOCK (FAN NO. 1 RELAY, FAN NO. 2 RELAY)

NG

REPAIR OR REPLACE HARNESS AND CONNECTOR

2.INSPECT ENGINE ROOM RELAY BLOCK (FAN NO. 1 RELAY, FAN NO. 2 RELAY)
a.
A312094C01
0.052,0.073 0.365,0.229 0.313,0.156 10 false *1 0.208,3.25 0.521,3.406 0.313,0.156 10 false *2 2.281,0.333 2.594,0.49 0.313,0.156 10 false *3
*1 Engine Room Relay Block
*2 FAN No. 1 Relay
*3 FAN No. 2 Relay


Remove the FAN No. 1 relay and FAN No. 2 relay from the engine room relay block.


b.

Turn the ignition switch to ON.


c.

Check the voltage.

i.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
1 (FAN No. 1 relay) - Body ground Ignition switch ON 11 to 14 V
1 (FAN No. 2 relay) - Body ground




d.

Reinstall the FAN No. 1 relay and FAN No. 2 relay to the engine room relay block.

Result:
Result
OK
NG




OK

3.INSPECT FAN NO. 1 RELAY

NG

REPAIR OR REPLACE HARNESS AND CONNECTOR

3.INSPECT FAN NO. 1 RELAY
a.

Inspect the FAN No. 1 relay.

Click hereEngine / Hybrid System>1NR-FE COOLING>RELAY>ON-VEHICLE INSPECTION

Result:
Result
OK
NG




OK

4.INSPECT FAN NO. 2 RELAY

NG

REPLACE FAN NO. 1 RELAY

4.INSPECT FAN NO. 2 RELAY
a.

Inspect the FAN No. 2 relay.

Click hereEngine / Hybrid System>1NR-FE COOLING>RELAY>ON-VEHICLE INSPECTION

Result:
Result
OK
NG




OK

5.INSPECT COOLING FAN RESISTOR

NG

REPLACE FAN NO. 2 RELAY

5.INSPECT COOLING FAN RESISTOR
a.

Inspect the cooling fan resistor.

Click hereEngine / Hybrid System>1NR-FE COOLING>COOLING FAN RESISTOR>INSPECTION

Result:
Result
OK
NG




OK

6.CHECK HARNESS AND CONNECTOR (FAN NO. 2 RELAY - BODY GROUND)

NG

6.CHECK HARNESS AND CONNECTOR (FAN NO. 2 RELAY - BODY GROUND)
a.
A312093C01
0.115,0.125 0.427,0.281 0.313,0.156 10 false *1 2.313,0.167 2.625,0.323 0.313,0.156 10 false *2
*1 Engine Room Relay Block
*2 FAN No. 2 Relay


Remove the FAN No. 2 relay from the engine room relay block.


b.

Check the resistance.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
5 (FAN No. 2 relay) - Body ground Always Below 1 Ω




c.

Reinstall the FAN No. 2 relay to the engine room relay block.

Result:
Result
OK
NG




OK

7.CHECK HARNESS AND CONNECTOR (COOLING FAN RESISTOR - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS AND CONNECTOR

7.CHECK HARNESS AND CONNECTOR (COOLING FAN RESISTOR - BODY GROUND)
a.

Disconnect the A3 cooling fan resistor connector.


b.

Check the resistance.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A3-1 (-) - Body ground Always Below 1 Ω




c.

Reconnect the A3 cooling fan resistor connector.

Result:
Result
OK
NG




OK

8.CHECK HARNESS AND CONNECTOR (COOLING FAN RESISTOR - FAN NO. 2 RELAY)

NG

REPAIR OR REPLACE HARNESS AND CONNECTOR

8.CHECK HARNESS AND CONNECTOR (COOLING FAN RESISTOR - FAN NO. 2 RELAY)
a.

Disconnect the A3 cooling fan resistor connector.


b.
A312093C01
0.115,0.125 0.427,0.281 0.313,0.156 10 false *1 2.313,0.167 2.625,0.323 0.313,0.156 10 false *2
*1 Engine Room Relay Block
*2 FAN No. 2 Relay


Remove the FAN No. 2 relay from the engine room relay block.


c.

Check the resistance.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A3-2 (+) - 4 (FAN No. 2 relay) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
A3-2 (+) or 4 (FAN No. 2 relay) - Body ground Always 10 kΩ or higher




d.

Reinstall the FAN No. 2 relay to the engine room relay block.


e.

Reconnect the A3 cooling fan resistor connector.

Result:
Result
OK
NG




OK

9.INSPECT COOLING FAN MOTOR

NG

REPAIR OR REPLACE HARNESS AND CONNECTOR

9.INSPECT COOLING FAN MOTOR
a.

Inspect the cooling fan motor.

Click hereEngine / Hybrid System>1NR-FE COOLING>COOLING FAN MOTOR>ON-VEHICLE INSPECTION

Result:
Result
OK
NG




OK

10.CHECK HARNESS AND CONNECTOR (COOLING FAN MOTOR - FAN NO. 1 RELAY)

NG

10.CHECK HARNESS AND CONNECTOR (COOLING FAN MOTOR - FAN NO. 1 RELAY)
a.

Disconnect the A2 cooling fan motor connector.


b.
A312092C01
0.115,0.104 0.427,0.26 0.313,0.156 10 false *1 0.198,1.813 0.51,1.969 0.313,0.156 10 false *2
*1 Engine Room Relay Block
*2 FAN No. 1 Relay


Remove the FAN No. 1 relay from the engine room relay block.


c.

Check the resistance.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A2-2 - 5 (FAN No. 1 relay) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
A2-2 or 5 (FAN No. 1 relay) - Body ground Always 10 kΩ or higher




d.

Reinstall the FAN No. 1 relay to the engine room relay block.


e.

Reconnect the A2 cooling fan motor connector.

Result:
Result
OK
NG




OK

11.CHECK HARNESS AND CONNECTOR (COOLING FAN MOTOR - FAN NO. 2 RELAY)

NG

REPAIR OR REPLACE HARNESS AND CONNECTOR

11.CHECK HARNESS AND CONNECTOR (COOLING FAN MOTOR - FAN NO. 2 RELAY)
a.

Disconnect the A2 cooling fan motor connector.


b.
A312093C01
0.115,0.125 0.427,0.281 0.313,0.156 10 false *1 2.313,0.167 2.625,0.323 0.313,0.156 10 false *2
*1 Engine Room Relay Block
*2 FAN No. 2 Relay


Remove the FAN No. 2 relay from the engine room relay block.


c.

Check the resistance.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A2-1 - 3 (FAN No. 2 relay) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
A2-1 or 3 (FAN No. 2 relay) - Body ground Always 10 kΩ or higher




d.

Reinstall the FAN No. 2 relay to the engine room relay block.


e.

Reconnect the A2 cooling fan motor connector.

Result:
Result
OK
NG




OK

12.CHECK HARNESS AND CONNECTOR (ENGINE ROOM RELAY BLOCK - ECM)

NG

REPAIR OR REPLACE HARNESS AND CONNECTOR

12.CHECK HARNESS AND CONNECTOR (ENGINE ROOM RELAY BLOCK - ECM)
a.
A312094C01
0.052,0.073 0.365,0.229 0.313,0.156 10 false *1 0.208,3.25 0.521,3.406 0.313,0.156 10 false *2 2.281,0.333 2.594,0.49 0.313,0.156 10 false *3
*1 Engine Room Relay Block
*2 FAN No. 1 Relay
*3 FAN No. 2 Relay


Remove the FAN No. 1 relay and FAN No. 2 relay from the engine room relay block.


b.

c.

Check the resistance.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
2 (FAN No. 1 relay) - F131-5 (FANL) Always Below 1 Ω
2 (FAN No. 2 relay) - F131-6 (FANH)


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
2 (FAN No. 1 relay) or F131-5 (FANL) - Body ground Always 10 kΩ or higher
2 (FAN No. 2 relay) or F131-6 (FANH) - Body ground




d.

Reconnect the F131 ECM connector.


e.

Reinstall the FAN No. 1 relay and FAN No. 2 relay to the engine room relay block.

Result:
Result
OK
NG




OK

NG

REPAIR OR REPLACE HARNESS AND CONNECTOR