Home › Engine / Hybrid System › 1NR-FE ENGINE MECHANICAL › CYLINDER HEAD GASKET › from 2016.04
RM30M0E _51 Engine / Hybrid System _053932 1NR-FE ENGINE MECHANICAL _0262343 CYLINDER HEAD GASKET A

1NR-FE ENGINE MECHANICAL  CYLINDER HEAD GASKET  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:

Perform "Inspection After Repair" after replacing the cylinder head sub-assembly.

Click hereEngine / Hybrid System>1NR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION


PROCEDURE

Hide 11115 1.INSTALL CYLINDER HEAD GASKET

a.

Clean and degrease the lower surface of the cylinder head sub-assembly and upper surface of the cylinder block sub-assembly.


b.
A206031C12
1.938,2.25 2.167,2.49 true 0.844,0.094 2.948,0.302 2.104,0.208 10 false 4.0 to 7.0 mm (0.157 to 0.276 in.) 0.292,0.635 1.479,1.177 1.188,0.542 10 false 6.5 to 8.0 mm (0.256 to 0.315 in.) 0.271,2.146 1.469,2.479 1.198,0.333 10 false 6.5 to 8.0 mm (0.256 to 0.315 in.) 0.333,3.74 1.531,4.073 1.198,0.333 10 false 7.0 to 10.0 mm (0.276 to 0.394 in.) 0.917,2.771 3.021,2.979 2.104,0.208 10 false 4.0 to 7.0 mm (0.157 to 0.276 in.) 1.229,3.177 3.333,3.385 2.104,0.208 10 false 4.0 to 7.0 mm (0.157 to 0.276 in.) 2.188,2.521 2.51,2.76 0.323,0.24 10 false *a
*a Bead


Apply seal packing to a new cylinder head gasket as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


NOTICE:

Install the cylinder head sub-assembly within 3 minutes and tighten the cylinder head set bolts within 15 minutes of applying seal packing.


HINT:

Apply seal packing to the bead on the cylinder head gasket.



c.
A286289C04
2.073,1.979 2.073,1.708 true 2.021,1.979 2.333,2.177 0.313,0.198 10 false *a
*a Lot No.
V100135

Engine Front


Place the cylinder head gasket on the cylinder block sub-assembly surface with the Lot No. stamp facing upward.

NOTICE:
·

Remove any oil from the contact surface.

·

Make sure that the cylinder head gasket is installed in the correct direction.




Hide 11101 2.INSTALL CYLINDER HEAD SUB-ASSEMBLY

a.

Apply a light coat of engine oil to the cylinder head set bolt threads and area beneath the cylinder head set bolt heads that come in contact with the plate washers.


b.

Install the 10 cylinder head set bolts and 10 plate washers to the cylinder head sub-assembly.

NOTICE:

Do not drop the plate washers into the cylinder head sub-assembly.



c.
A286216E03
1.49,0.24 1.646,0.438 0.156,0.198 10 false 1 1.5,1.844 1.656,2.042 0.156,0.198 10 false 2 2.052,0.24 2.208,0.438 0.156,0.198 10 false 3 0.958,1.844 1.115,2.042 0.156,0.198 10 false 4 2.052,1.854 2.208,2.052 0.156,0.198 10 false 5 0.948,0.25 1.104,0.448 0.156,0.198 10 false 6 2.594,1.854 2.75,2.052 0.156,0.198 10 false 7 0.438,0.26 0.594,0.458 0.156,0.198 10 false 8 2.583,0.26 2.74,0.458 0.156,0.198 10 true 9 0.427,1.833 0.74,2.031 0.313,0.198 10 false 10

Using a 10 mm bi-hexagon wrench, uniformly install and tighten the 10 cylinder head set bolts and 10 plate washers in several steps in the sequence shown in the illustration.

Torque:
32 N*m (326 kgf*cm, 24 ft.*lbf)


d.
A299215C01
1.271,1.667 1.958,1.073 false 1.406,0.458 1.865,0.656 0.458,0.198 10 90° 2.927,0.323 3.385,0.521 0.458,0.198 10 90° 1.094,1.635 1.552,1.833 0.458,0.198 10 *a
*a Paint Mark
V100135

Engine Front


Mark the engine front of the cylinder head set bolts with paint.


e.

Tighten the cylinder head set bolts an additional 90°, then once more 90° as shown in the illustration.

NOTICE:

Do not tighten the same cylinder head set bolt twice consecutively.



f.

Check that the paint mark is now at a 180° angle to the engine front.


g.
A380913C01
1.646,0.313 1.958,0.469 0.313,0.156 10 false *a 0.938,2.844 1.25,3 0.313,0.156 10 false *b 2.135,2.854 2.448,3.01 0.313,0.156 10 false *c
*a Direction to wipe off
*b Before wiping off
*c After wiping off


Wipe off the seal packing seeped out from the contact surface between the cylinder head sub-assembly and cylinder block sub-assembly.

NOTICE:

Be sure to avoid clogging the bolt holes when wiping off the seal packing.


HINT:
·

Be sure to wipe off the seal packing from inside to outside, in parallel to the joint line.

·

Perform "Inspection After Repair" after replacing the cylinder head sub-assembly.

Click hereEngine / Hybrid System>1NR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION




Hide 22030 3.INSTALL INTAKE MANIFOLD WITH THROTTLE BODY WITH MOTOR ASSEMBLY

Hide 16264 4.CONNECT NO. 2 WATER BY-PASS HOSE

Hide 16267 5.CONNECT NO. 3 WATER BY-PASS HOSE

Hide 23291 6.INSTALL INJECTOR VIBRATION INSULATOR

a.
A380914

Apply a light coat of gasoline or spindle oil to new injector vibration insulators and then install one to each fuel injector assembly.


Hide 23891 7.INSTALL FUEL DELIVERY SPACER

Hide 23814B 8.INSTALL FUEL DELIVERY PIPE

Hide 25051 9.INSTALL EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY