Home › Engine / Hybrid System › 1NR-FE ENGINE MECHANICAL › ENGINE UNIT › 2016.04–2017.10
RM30M0E _51 Engine / Hybrid System _053932 1NR-FE ENGINE MECHANICAL _0262434 ENGINE UNIT A

1NR-FE ENGINE MECHANICAL  ENGINE UNIT  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:

Perform "Inspection After Repair" after replacing the ignition coil assembly or fuel injector assembly.

Click hereEngine / Hybrid System>1NR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION


PROCEDURE

Hide 1.INSTALL WIRE HARNESS CLAMP BRACKET

a.

Install the wire harness clamp bracket to the cylinder block sub-assembly with the bolt.

Torque:
12.8 N*m (131 kgf*cm, 9 ft.*lbf)


b.
A312283E01
2.271,1.594 2.427,1.792 0.156,0.198 10 true A 2.719,1.063 2.875,1.26 0.156,0.198 10 true B

Install the 2 wire harness clamp brackets to the cylinder head sub-assembly with the 2 bolts.

Torque:
Bolt A : 29 N*m (296 kgf*cm, 21 ft.*lbf)
Bolt B : 8.4 N*m (86 kgf*cm, 74 in.*lbf)


c.

Install the wire harness clamp bracket to the cylinder head cover sub-assembly with the bolt.

Torque:
8.4 N*m (86 kgf*cm, 74 in.*lbf)


Hide 16620 2.INSTALL V-RIBBED BELT TENSIONER ASSEMBLY

a.

Install the V-ribbed belt tensioner assembly to the timing chain cover assembly with the 2 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 16268 3.INSTALL NO. 1 WATER BY-PASS PIPE

a.

Connect the No. 1 water by-pass hose to the water inlet with thermostat sub-assembly and slide the hose clip to secure it.


b.

Install the No. 1 water by-pass pipe to the cylinder block sub-assembly with the bolt.

Torque:
22 N*m (224 kgf*cm, 16 ft.*lbf)


c.

Engage the clamp to connect the water by-pass hose to the hose clamp.


Hide 4.INSTALL NO. 2 VENTILATION HOSE

a.
A381478C02
2.167,0.333 2.448,0.448 false 3.094,2.188 3.375,2.458 0.281,0.271 10 false A 1.979,0.229 2.292,0.385 0.313,0.156 10 false *b 2.396,0.104 2.708,0.26 0.313,0.156 10 false *c 1.698,0.125 2.01,0.281 0.313,0.156 10 false *a
*a View A
*b Paint Mark
*c Top of Engine


Install the No. 2 ventilation hose to the cylinder head cover sub-assembly and slide the hose clip to secure it.

NOTICE:

Perform the installation with the No. 2 ventilation hose and hose clip at the correct angle.



Hide 6.INSTALL INTAKE MANIFOLD WITH THROTTLE BODY WITH MOTOR ASSEMBLY

a.

Install a new No. 1 intake manifold to head gasket to the intake manifold.


b.
A381449E01
0.729,0.802 0.885,1 0.156,0.198 10 true 4 1.583,0.01 1.74,0.208 0.156,0.198 10 true 2 2.052,0.135 2.208,0.333 0.156,0.198 10 true 1 2.521,0 2.677,0.198 0.156,0.198 10 true 3 3.271,0.302 3.427,0.5 0.156,0.198 10 true 5

Temporarily install the intake manifold with the throttle body with motor assembly to the cylinder head sub-assembly with the 3 bolts and 2 nuts.

NOTICE:

Make sure there is no oil adhering to the bolts or threaded holes.



c.

Fully tighten the 3 bolts and 2 nuts, in the sequence shown in the illustration.

Torque:
28 N*m (286 kgf*cm, 21 ft.*lbf)


Hide 16264 7.CONNECT NO. 2 WATER BY-PASS HOSE

a.
A313290C01
1.198,0.667 1.438,0.458 false 0.25,0.156 0.563,0.313 0.313,0.156 10 false *a 1.479,0.375 1.792,0.531 0.313,0.156 10 false *b 0.927,0.104 1.24,0.26 0.313,0.156 10 false *c 1.292,2.042 1.458,2.208 0.167,0.167 10 true A
*a View A
*b Paint Mark
*c Front of Engine


Connect the No. 2 water by-pass hose to the cylinder head sub-assembly and slide the hose clip to secure it.

NOTICE:

Perform the installation with the No. 2 water by-pass hose and hose clip at the correct angle.



Hide 16267 8.CONNECT NO. 3 WATER BY-PASS HOSE

a.
A312368C01
1.896,0.833 2.198,0.719 false 1.646,0.146 1.958,0.302 0.313,0.156 10 false *a 1.698,0.76 2.01,0.917 0.313,0.156 10 false *b 2.333,0.135 2.646,0.292 0.313,0.156 10 false *c 2.01,2.344 2.208,2.521 0.198,0.177 10 true A
*a View A
*b Paint Mark
*c Top of Engine


Connect the No. 3 water by-pass hose to the throttle body with motor assembly and slide the hose clip to secure it.

NOTICE:

Perform the installation with the No. 3 water by-pass hose and hose clip at the correct angle.



Hide 12261 9.INSTALL VENTILATION HOSE

a.
A390499C01
1.917,0.25 2.917,1.25 1,1 1.917,1.25 2.917,2.167 1,0.917 1.583,0.167 3,2.25 1.417,2.083 0.333,0.167 1.583,2.25 1.25,2.083 0.802,1.656 0.958,1.458 true 2.083,0.917 2.177,0.719 true 2.698,2.042 2.448,2 true 0.417,0.25 0.594,0.448 0.177,0.198 10 false *a 1.667,0.25 1.844,0.448 0.177,0.198 10 false *b 1.01,0.74 1.188,0.938 0.177,0.198 10 false *f 2.458,0.271 2.635,0.469 0.177,0.198 10 false *f 2.438,1.323 2.615,1.521 0.177,0.198 10 false *f 0.646,1.625 0.823,1.823 0.177,0.198 10 false *e 1.979,0.917 2.156,1.115 0.177,0.198 10 false *e 2.74,1.969 2.917,2.167 0.177,0.198 10 false *e 2,0.281 2.208,0.458 0.208,0.177 10 false *c 2,1.333 2.208,1.51 0.208,0.177 10 false *d 0.948,3.76 1.104,3.927 0.156,0.167 10 true A 2.906,2.604 3.063,2.771 0.156,0.167 10 true B
*a View A
*b View B
*c Type A
*d Type B
*e Paint Mark
*f Exhaust Side


Install the ventilation hose to the cylinder head cover sub-assembly and intake manifold and slide the 2 hose clips to secure them.

NOTICE:

Perform the installation with the ventilation hose and hose clip at the correct angle.



b.

Engage the 2 clamps to connect the ventilation hose to the hose clamp.


Hide 10.INSTALL FUEL INJECTOR ASSEMBLY

Hide 23891 11.INSTALL FUEL DELIVERY SPACER

Hide 23814B 12.INSTALL FUEL DELIVERY PIPE

Hide 25051 13.INSTALL EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY