Based on the vehicle speed signal received from the combination meter assembly, the power steering ECU assembly adjusts the amount of power assist according to the vehicle speed. The power steering ECU assembly monitors the speed signal input and stores a DTC if a malfunction is detected. While a malfunction exists in the vehicle speed signal, fail-safe operation maintains the amount of power assist at the level used for a speed of 70 km/h (43 mph).
Revving the engine while the vehicle is stopped may cause DTC C1541 or C1542 to be stored.
If C1541 is stored while the vehicle is stopped, driving the vehicle for 5 minutes or more and then turning the ignition switch off will clear the DTC.
If C1542 is stored while the vehicle is stopped, driving the vehicle for 5 minutes or more will clear the DTC.
A voltage of 12 V or 5 V is output from each ECU and then input to the combination meter assembly. Each ECU controls its respective system based on the vehicle speed pulse signal.
If a short occurs in any of the ECUs or in a wire harness connected to an ECU, all systems in the diagram below will not operate normally.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Return-to-normal Condition | Note |
|---|---|---|---|---|---|
| C1541 | Vehicle Speed Signal Malfunction | ·
A vehicle speed signal indicating an abnormal increase in vehicle speed. ·
While the vehicle is stopped, the engine speed exceeds the threshold* for a total of 300 seconds or more. |
·
Vehicle speed signal circuit ·
Combination meter assembly ·
Power steering ECU assembly |
Ignition switch turned to ON again or after system confirmed to be normal | Power Steering Warning Light comes on. |
| C1542 | Vehicle Speed Signal Malfunction | ·
A vehicle speed signal indicating an abnormal decrease in vehicle speed. ·
While the vehicle is stopped, the engine speed exceeds the threshold* for a total of 30 seconds or more. |
·
Vehicle speed signal circuit ·
Combination meter assembly ·
Power steering ECU assembly |
Ignition switch turned to ON again or after system confirmed to be normal | Power Steering Warning Light does not illuminate (normal reset). |
| C1571 | Speed Sensor Malfunction (Test Mode DTC) | A speed sensor malfunction (Test Mode DTC). | ·
Vehicle speed signal circuit ·
Combination meter assembly ·
Power steering ECU assembly |
- | Power Steering Warning Light does not illuminate (normal reset). |
*: Threshold: An engine speed of 4000 rpm or more is detected within 5 minutes after the engine is started, or an engine speed of 2100 rpm or more is detected 5 minutes or more after the engine is started.
If the power steering ECU assembly, electric power steering column sub-assembly or power steering motor assembly have been replaced, perform torque sensor zero point calibration.
Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>CALIBRATION
Perform the signal check in the Test Mode procedure.
| Tester Display |
|---|
| Signal Check |
Test mode DTC C1571 is cleared.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
The circuits that send vehicle speed signals to this system are inspected in the meter / gauge system.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>Speedometer Malfunction
During inspection for the meter section, if there is an instruction that indicates to go back to inspections for each system, proceed to the next step.
| Proceed to |
|---|
| NEXT |
NEXT
Disconnect the F12 power steering ECU assembly connector.
Disconnect the F38 combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F12-2 (SPD) - F38-35 (+S) | Always | Below 1 Ω |
| F12-2 (SPD) or F38-35 (+S) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Rear view of wire harness connector
(to Power Steering ECU Assembly) |
Disconnect the power steering ECU assembly connectors.
Use a lift to raise the vehicle until the tires are off the ground.
Start the engine.
Depress the clutch pedal*1 or brake pedal*2.
Move the shift lever to the 1st position*1 or shift lever to D*2.
Engage the clutch*1 or slowly release the brake pedal*2.
Check that the front wheels rotate slowly.
Be careful not to get caught in the front wheels while they are rotating.
Check the signal waveform according to the condition(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F12-2 (SPD) -F11-2 (PGND) | Front wheels rotating at speed corresponding to vehicle speed of approximately 20 km/h (12 mph) | Correct waveform appears as shown |
| Item | Condition |
|---|---|
| Tool setting | 5 V/DIV., 20 ms./DIV. |
| Vehicle Condition | Vehicle being driven at approximately 20 km/h (12 mph) |
The wavelength becomes shorter as the vehicle speed increases.
*1: for Manual Transaxle
*2: for Automatic Transaxle and CVT
| Proceed to |
|---|
| OK |
| NG |
OK
NG