Home › Brake › PARKING BRAKE › PARKING BRAKE CABLE › 2016.04–2016.07
RM30M0E _54 Brake _017102 PARKING BRAKE _0092773 PARKING BRAKE CABLE A

PARKING BRAKE  PARKING BRAKE CABLE  REMOVAL  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the LH side (No. 3 parking brake cable assembly) and RH side (No. 2 parking brake cable assembly).

·

The following procedure is for the LH side (No. 3 parking brake cable assembly).



PROCEDURE

Hide 58910C 1.REMOVE REAR CONSOLE BOX ASSEMBLY (w/ Console Box Lid)

Hide 58910C 2.REMOVE REAR CONSOLE BOX ASSEMBLY (w/o Console Box Lid)

Hide 46430 3.DISCONNECT NO. 3 PARKING BRAKE CABLE ASSEMBLY

a.
C282403C03
1.083,1.656 1.729,1.281 true 0.938,1.583 1.135,1.781 0.198,0.198 10 false *1
*1 Lock Nut


Loosen the lock nut.

NOTICE:

If the lock nut has been removed from the rod, replace the lock nut with a new one.



b.
C282413

Disengage the claw and 2 guides to remove the parking brake cable end stopper from the parking brake equalizer.


c.
C282414C02
1.292,0.385 1.604,0.646 false 2.594,0.49 2.323,0.802 false 2.344,1.5 2.656,1.76 false 1.146,0.292 1.458,0.448 0.313,0.156 10 false *1 2.625,0.375 2.938,0.531 0.313,0.156 10 false *2 2.688,1.677 3,1.833 0.313,0.156 10 false *3
*1 Parking Brake Equalizer
*2 No. 2 Parking Brake Cable Assembly
*3 No. 3 Parking Brake Cable Assembly


Disconnect the No. 3 parking brake cable assembly from the parking brake equalizer.


Hide 51451A 4.REMOVE CENTER ENGINE UNDER COVER (for RH Side w/ Metal Type Under Cover)

Hide 51405A 5.REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY (for RH Side w/ Metal Type Under Cover)

Hide 10.REMOVE REAR WHEEL (for Rear Drum Brake)

Hide 42403 11.REMOVE REAR BRAKE DRUM SUB-ASSEMBLY (for Rear Drum Brake)

Hide 12.REMOVE REAR BRAKE STRUT KIT (for Rear Drum Brake)

Hide 89516D 13.SEPARATE SKID CONTROL SENSOR WIRE (w/ ABS)

a.
C285148

Remove the nut to separate the skid control sensor wire from the rear axle beam assembly.


Hide 46430 14.REMOVE NO. 3 PARKING BRAKE CABLE ASSEMBLY (for Rear Drum Brake)

a.
C109000

Remove the bolt to disconnect the No. 3 parking brake cable assembly from the backing plate.


b.

Disengage clamp to remove the parking brake cable clamp.

C282415C02
1.5,3.365 1.771,3.24 true 4.198,2.771 3.927,2.625 false 3.781,2.542 3.979,2.729 0.198,0.188 10 false *1 1.344,3.292 1.656,3.448 0.313,0.156 10 false *2
*1 Parking Brake Cable Clamp *2 No. 3 Parking Brake Cable Assembly



c.

Remove the No. 3 parking brake cable assembly from the parking brake cable clamp.


d.

Remove the 3 bolts to separate the No. 3 parking brake cable assembly from the body.


e.

Remove the nut and No. 3 parking brake cable assembly from the rear axle beam assembly.


Hide 46430 15.REMOVE NO. 3 PARKING BRAKE CABLE ASSEMBLY (for Rear Disc Brake)

a.
C282418

Disconnect the No. 3 parking brake cable assembly from the rear disc brake cylinder assembly.


b.
C282419C01
2.417,1.396 2.635,1.5 false 2.823,1.271 2.99,1.271 false 3.021,1.167 3.333,1.323 0.313,0.156 10 false *1 2.26,1.292 2.573,1.448 0.313,0.156 10 false *a
*1 No. 3 Parking Brake Cable Assembly
*a Clip


Insert a 14 mm offset wrench at the base of the No. 3 parking brake cable assembly as shown in the illustration to disengage the clip, and separate the No. 3 parking brake cable assembly from the rear disc brake cylinder assembly.


c.

Disengage clamp to remove the parking brake cable clamp.

C282415C02
1.5,3.365 1.771,3.24 true 4.198,2.771 3.927,2.625 false 3.781,2.542 3.979,2.729 0.198,0.188 10 false *1 1.344,3.292 1.656,3.448 0.313,0.156 10 false *2
*1 Parking Brake Cable Clamp *2 No. 3 Parking Brake Cable Assembly



d.

Remove the No. 3 parking brake cable assembly from the parking brake cable clamp.


e.

Remove the 3 bolts to separate the No. 3 parking brake cable assembly from the body.


f.

Remove the nut and No. 3 parking brake cable assembly from the rear axle beam assembly.