Home › Drivetrain › U340E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE ASSEMBLY › 2016.07–2016.10
RM30M0E _52 Drivetrain _017087 U340E AUTOMATIC TRANSMISSION / TRANSAXLE _0090613 AUTOMATIC TRANSAXLE ASSEMBLY A

U340E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE ASSEMBLY  REMOVAL  


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 23827A 6.DISCONNECT NO. 2 FUEL VAPOR FEED HOSE

Hide 23820 7.DISCONNECT FUEL VAPOR FEED HOSE ASSEMBLY

Hide 17341T 8.DISCONNECT NO. 1 AIR HOSE

Hide 17735 9.REMOVE AIR CLEANER CAP WITH NO. 1 AIR CLEANER HOSE

Hide 17801 10.REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

Hide 33820B 16.DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

NOTICE:

To prevent damage to the transmission control cable assembly and transmission floor shift assembly, disconnect the transmission floor shift assembly side of the transmission control cable assembly before disconnecting the automatic transaxle assembly side.


a.

Apply the parking brake and move the shift lever to N.


b.
C286312

Disconnect the end of the transmission control cable assembly from the transmission floor shift assembly.


c.
C282050

Remove the nut to disconnect the transmission control cable assembly from the transmission control shaft lever.


d.

Remove the clip to separate the transmission control cable assembly from the No. 1 transmission control cable bracket.


e.
C282036

Separate the transmission control cable assembly from the transmission control cable support.


Hide 82123 17.DISCONNECT NO. 3 ENGINE WIRE

a.
C283254

Remove the bolt to disconnect the No. 3 engine wire from the automatic transaxle assembly.


b.

Disengage the 2 clamps to separate the No. 3 engine wire from the engine mounting bracket LH.


Hide 82121 18.DISCONNECT ENGINE WIRE

a.
C283252C01
0.813,1.115 1.198,1.021 true 1.813,1.104 2.094,1.063 true 3.031,1.615 2.813,1.479 true 0.635,1.021 0.813,1.219 0.177,0.198 10 true *1 2.125,0.958 2.333,1.167 0.208,0.208 10 true *2 3.052,1.521 3.26,1.719 0.208,0.198 10 true *1
*1 Wire Harness Clamp Bracket
*2 Transmission Control Cable Support


Disconnect the 3 connectors from the automatic transaxle assembly.


b.

Disengage the 6 clamps to separate the engine wire.


c.

Remove the 3 bolts, 2 wire harness clamp brackets and transmission control cable support from the automatic transaxle assembly.


Hide 19.REMOVE FRONT DRIVE SHAFT ASSEMBLIES

Hide 28100 20.REMOVE STARTER ASSEMBLY

Hide 32941 21.DISCONNECT INLET NO. 1 OIL COOLER HOSE

a.
C282058

Slide the hose clip and disconnect the inlet No. 1 oil cooler hose from the inlet No. 1 oil cooler tube.


Hide 32942 22.DISCONNECT OUTLET NO. 1 OIL COOLER HOSE

a.
C282059

Slide the hose clip and disconnect the outlet No. 1 oil cooler hose from the outlet No. 1 oil cooler tube.


Hide 11361J 23.REMOVE FLYWHEEL HOUSING UNDER COVER

a.
C282062

Remove the flywheel housing under cover from the engine assembly.


Hide 32101A 24.REMOVE DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT

a.
A107285E03
1.677,1.948 1.958,1.948 false 2,1.854 2.333,2.073 0.333,0.219 10 false SST

Using SST, hold the crankshaft pulley.

SST
09960-10010  (09962-01000, 09963-01000)


b.
C282063

Remove the 6 drive plate and torque converter assembly setting bolts.


Hide 51201 25.REMOVE FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY

Hide 26.SUPPORT ENGINE ASSEMBLY

a.
C282060C01
1.958,1.188 1.375,0.458 1.375,0.458 1.563,1.094 true 0.552,2.063 0.552,1.875 false 1.188,0.333 1.354,0.5 0.167,0.167 10 true *a 0.5,2.073 0.813,2.229 0.313,0.156 10 false *b
*a Attachment
*b Engine Lifter
V100155

Attachment Placement Positions


Place the height adjustment attachments or plate lift attachments in the positions shown in the illustration and set the engine lifter underneath the engine assembly.

NOTICE:
·

Place the height adjustment attachments or plate lift attachments so that the engine assembly with the automatic transaxle assembly is level.

·

As the engine assembly with the automatic transaxle assembly is very heavy, be sure to support it securely.

·

To prevent deformation of the No. 2 oil pan sub-assembly, never set any attachments against the No. 2 oil pan sub-assembly of the engine assembly.

·

To prevent deformation of the automatic transaxle oil pan sub-assembly, never set any attachments against the automatic transaxle oil pan sub-assembly.




Hide 12321B 27.REMOVE DRIVE SHAFT HEAT INSULATOR SUB-ASSEMBLY

a.
C282064

Using a 12 mm deep socket wrench, remove the nut.


b.

Remove the bolt and drive shaft heat insulator sub-assembly from the engine assembly.


Hide 12364B 28.REMOVE NO. 2 ENGINE MOVING CONTROL ROD

C282065

a.

Remove the 3 bolts and No. 2 engine moving control rod from the automatic transaxle assembly.


Hide 30500 29.REMOVE AUTOMATIC TRANSAXLE ASSEMBLY

a.
C282061C01
2.927,2.125 2.49,1.948 true 1.99,0.49 1.677,0.323 true 2.958,2.031 3.156,2.229 0.198,0.198 10 false *a 1.5,0.229 1.698,0.417 0.198,0.188 10 true *b
*a Transmission Jack
*b Lashing Belt
V100155

Attachment Placement Positions


On a flat location, set the attachments in the positions shown in the illustration and set the transmission jack underneath the automatic transaxle assembly.

NOTICE:
·

To prevent deformation of the automatic transaxle oil pan sub-assembly, never set any attachments against the automatic transaxle oil pan sub-assembly.

·

Secure the automatic transaxle assembly to the transmission jack with a lashing belt, etc., to prevent the automatic transaxle assembly from falling.




b.
C282066

Remove the bolt and nut to separate the engine mounting bracket LH from the engine mounting insulator LH.

HINT:

Turn the bolt while holding the nut.



c.
C282067

Remove the 4 bolts and engine mounting bracket LH from the automatic transaxle assembly.


d.
C283076E01
0.906,0.073 1.052,0.25 0.146,0.177 10 false A 2.365,0.031 2.51,0.208 0.146,0.177 10 false A 2.51,1.885 2.656,2.063 0.146,0.177 10 false B 2.167,2 2.313,2.177 0.146,0.177 10 false B 1.281,2 1.427,2.177 0.146,0.177 10 false B 0.646,0.906 0.792,1.083 0.146,0.177 10 true B 0.906,1.708 1.031,1.885 0.125,0.177 10 true B

Remove the 7 bolts and automatic transaxle assembly from the engine assembly.

NOTICE:
·

Make sure that the engine assembly is not tilted.

·

To prevent damage to the knock pins, do not pry between the automatic transaxle assembly and engine assembly.

·

Do not allow the torque converter assembly to fall off.



HINT:
·

Bolt A: Remove from automatic transaxle assembly side

·

Bolt B: Remove from engine assembly side




Hide 30.REMOVE TORQUE CONVERTER ASSEMBLY

a.
C283099

Remove the torque converter assembly from the automatic transaxle assembly.

NOTICE:

Remove the torque converter assembly from the input shaft horizontally.



Hide 33823 31.REMOVE NO. 1 TRANSMISSION CONTROL CABLE BRACKET

C282057

a.

Remove the 2 bolts and No. 1 transmission control cable bracket from the automatic transaxle assembly.


Hide 32921 32.DISCONNECT INLET NO. 1 OIL COOLER TUBE

a.
C244610C01
1.677,1.208 1.885,1.417 0.208,0.208 10 true *a 0.115,0.49 0.313,0.677 0.198,0.188 10 false *b
*a Hold
*b Turn


Using a 14 mm union nut wrench, disconnect the inlet No. 1 oil cooler tube while holding the oil cooler tube union with a wrench.


Hide 32922 33.DISCONNECT OUTLET NO. 1 OIL COOLER TUBE

a.
C244611C01
2.781,1.833 2.948,2.021 0.167,0.188 10 true *a 1.271,1.615 1.448,1.802 0.177,0.188 10 false *b
*a Hold
*b Turn


Using a 14 mm union nut wrench, disconnect the outlet No. 1 oil cooler tube while holding the oil cooler tube union with a wrench.


Hide 32924 34.REMOVE NO. 2 OIL COOLER TUBE CLAMP

C118507

a.

Remove the bolt and No. 2 oil cooler tube clamp from the transmission oil filler tube sub-assembly.


b.

Remove the inlet No. 1 oil cooler tube and outlet No. 1 oil cooler tube from the automatic transaxle assembly.


Hide 35103 35.REMOVE TRANSMISSION OIL LEVEL DIPSTICK SUB-ASSEMBLY

a.

Remove the transmission oil level dipstick sub-assembly from the transmission oil filler tube sub-assembly.


Hide 35013 36.REMOVE TRANSMISSION OIL FILLER TUBE SUB-ASSEMBLY

C283101

a.

Disconnect the breather hose from the transmission oil filler tube sub-assembly.


b.

Remove the bolt and transmission oil filler tube sub-assembly from the automatic transaxle assembly.


c.

Remove the O-ring from the transmission oil filler tube sub-assembly.


Hide 33403M 37.REMOVE SPEEDOMETER DRIVEN HOLE COVER SUB-ASSEMBLY

a.
C162524

Remove the bolt and speedometer driven hole cover sub-assembly from the automatic transaxle assembly.


b.

Remove the O-ring from the speedometer driven hole cover sub-assembly.