Home › Engine / Hybrid System › 1NZ-FE ENGINE CONTROL › SFI SYSTEM(for Automatic Transaxle) › 2016.07–2016.10
RM30M0E _51 Engine / Hybrid System _017071 1NZ-FE ENGINE CONTROL _0090157 SFI SYSTEM(for Automatic Transaxle) J

1NZ-FE ENGINE CONTROL  SFI SYSTEM(for Automatic Transaxle)  VC Output Circuit  


DESCRIPTION

The ECM constantly generates a 5 V power source voltage from the battery voltage supplied to the +B (BATT) terminal to operate the microprocessor. The ECM also provides this power source voltage to the sensors through the VC output circuit.

A206916E24
4.375,1.177 6.198,1.354 1.823,0.177 10 false 5 V Constant Voltage Circuit 5.354,2.031 6.365,2.188 1.01,0.156 10 false Microprocessor 1.281,1.125 2.677,1.365 1.396,0.24 10 false from EFI NO. 3 Fuse 1.281,1.479 2.646,1.646 1.365,0.167 10 false from EFI-MAIN Fuse 2.906,1 3.427,1.219 0.521,0.219 10 false BATT 0.313,2.135 2.635,2.677 2.323,0.542 10 false Throttle Position Sensor, Accelerator Pedal Position Sensor, etc. (Sensors which have IC) 0.313,3.021 2.677,3.448 2.365,0.427 10 false Engine Coolant Temperature Sensor, Intake Air Temperature Sensor, etc. 4.073,3.115 4.333,3.323 0.26,0.208 10 false R 2.813,1.354 3.375,1.552 0.563,0.198 10 false +B, +B2 3.167,2.271 3.458,2.5 0.292,0.229 10 false VC 4.885,3.333 5.229,3.51 0.344,0.177 10 false ECM

When the VC circuit is short-circuited, the microprocessor in the ECM and the sensors that are supplied with power through the VC circuit are inactivated because power is not supplied from the VC circuit. Under this condition, the system does not start up and the MIL does not illuminate even if the system malfunctions.

HINT:

Under normal conditions, the MIL is illuminated when the ignition switch is turned ON. The MIL goes off when the engine is started.


WIRING DIAGRAM

A254095E27
4.573,1.094 4.844,1.24 0.271,0.146 10 false B29 0.396,2.354 2.594,2.531 2.198,0.177 10 false Throttle Body with Motor Assembly 0.438,5.323 2.802,5.5 2.365,0.177 10 false Accelerator Pedal Sensor Assembly 1.979,0.698 2.229,0.875 0.25,0.177 10 false VC 1.792,2.927 2.219,3.104 0.427,0.177 10 false VCPA 1.792,3.292 2.208,3.469 0.417,0.177 10 false VCP2 1.885,3.677 2.24,3.854 0.354,0.177 10 false VPA 1.813,4.031 2.219,4.208 0.406,0.177 10 false VPA2 1.885,4.417 2.198,4.594 0.313,0.177 10 false EPA 1.813,4.771 2.208,4.948 0.396,0.177 10 false EPA2 4.896,2.854 5.51,3.031 0.615,0.177 10 false VCPA 4.896,3.24 5.51,3.417 0.615,0.177 10 false VCP2 4.896,3.688 5.51,3.865 0.615,0.177 10 false VPA 4.896,4.052 5.51,4.229 0.615,0.177 10 false VPA2 4.885,4.333 5.5,4.51 0.615,0.177 10 false EPA 4.885,4.698 5.5,4.875 0.615,0.177 10 false EPA2 1.896,1.063 2.208,1.24 0.313,0.177 10 false VTA 1.813,1.427 2.208,1.604 0.396,0.177 10 false VTA2 1.99,1.813 2.219,1.99 0.229,0.177 10 false E2 4.896,0.625 5.51,0.802 0.615,0.177 10 false VCTA 5.521,5.479 5.865,5.656 0.344,0.177 10 false ECM 4.896,1.063 5.51,1.24 0.615,0.177 10 false VTA1 4.896,1.438 5.51,1.615 0.615,0.177 10 false VTA2 4.885,1.76 5.5,1.938 0.615,0.177 10 false ETA 0.396,2.198 0.677,2.354 0.281,0.156 10 false B17 4.563,1.844 4.833,1.99 0.271,0.146 10 false B29 4.573,3.688 4.854,3.948 0.281,0.26 10 false F83 4.573,4.063 4.844,4.208 0.271,0.146 10 false F83 4.563,4.438 4.833,4.583 0.271,0.146 10 false F83 4.573,4.802 4.844,4.948 0.271,0.146 10 false F83 4.573,2.958 4.844,3.104 0.271,0.146 10 false F83 4.573,3.323 4.833,3.51 0.26,0.188 10 false F83 4.573,1.469 4.844,1.615 0.271,0.146 10 false B29 4.573,0.729 4.844,0.875 0.271,0.146 10 false B29 4.615,1.677 4.792,1.833 0.177,0.156 10 false 28 4.604,3.135 4.792,3.313 0.188,0.177 10 false 27 4.615,3.5 4.865,3.75 0.25,0.25 10 false 18 4.615,4.625 4.802,4.781 0.188,0.156 10 false 21 4.604,4.25 4.792,4.406 0.188,0.156 10 false 20 4.615,3.875 4.917,4.052 0.302,0.177 10 false 19 4.604,2.76 4.792,2.917 0.188,0.156 10 false 26 4.604,1.292 4.865,1.448 0.26,0.156 10 false 19 4.615,0.927 4.875,1.083 0.26,0.156 10 false 20 4.615,0.531 4.792,0.688 0.177,0.156 10 false 18 2.292,1.365 2.385,1.521 0.094,0.156 10 false 4 2.292,1.719 2.385,1.875 0.094,0.156 10 false 3 2.292,2.823 2.385,2.979 0.094,0.156 10 false 4 2.292,3.198 2.385,3.354 0.094,0.156 10 false 1 2.292,4.688 2.385,4.844 0.094,0.156 10 false 2 2.292,4.323 2.385,4.479 0.094,0.156 10 false 5 2.292,3.948 2.385,4.104 0.094,0.156 10 false 3 2.292,3.573 2.385,3.729 0.094,0.156 10 false 6 2.292,0.979 2.385,1.135 0.094,0.156 10 false 6 2.292,0.594 2.385,0.75 0.094,0.156 10 false 5 5.833,0.458 6.094,0.625 0.26,0.167 10 false 5 V 0.438,5.146 1.354,5.323 0.917,0.177 10 false F85

PROCEDURE

1.CHECK MIL CONDITION
a.

Check that the Malfunction Indicator Lamp (MIL) lights up when turning the ignition switch to ON.

OK:

MIL lights up.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK CONNECTION BETWEEN GTS AND ECM
2.CHECK CONNECTION BETWEEN GTS AND ECM
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check for communication between the GTS and ECM.


Result:
Result Proceed to
Communication is not possible A
Communication is possible B



A

3.CHECK MIL (THROTTLE POSITION SENSOR)

B

3.CHECK MIL (THROTTLE POSITION SENSOR)
a.

Disconnect the B17 throttle body with motor assembly connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.


Result:
Result Proceed to
MIL does not illuminate A
MIL illuminates B



A

4.CHECK MIL (ACCELERATOR PEDAL SENSOR ASSEMBLY)

B

REPLACE THROTTLE BODY WITH MOTOR ASSEMBLY

4.CHECK MIL (ACCELERATOR PEDAL SENSOR ASSEMBLY)
a.

Disconnect the F85 accelerator pedal sensor assembly connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.


Result:
Result Proceed to
MIL does not illuminate A
MIL illuminates B



A

5.CHECK HARNESS AND CONNECTOR

B

REPLACE ACCELERATOR PEDAL SENSOR ASSEMBLY

5.CHECK HARNESS AND CONNECTOR
a.

Disconnect the B17 throttle body with motor assembly connector.


b.

Disconnect the F85 accelerator pedal sensor assembly connector.


c.

Disconnect the F83 and B29 ECM connectors.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B29-18 (VCTA) - Body ground Always 10 kΩ or higher
F83-26 (VCPA) - Body ground Always 10 kΩ or higher
F83-27 (VCP2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR