Use the same procedure for the LH side (No. 3 parking brake cable assembly) and RH side (No. 2 parking brake cable assembly).
The following procedure is for the LH side (No. 3 parking brake cable assembly).
46430
1.INSTALL NO. 3 PARKING BRAKE CABLE ASSEMBLY (for Rear Drum Brake)
Install the No. 3 parking brake cable assembly to the rear axle beam assembly with the nut.
Install the No. 3 parking brake cable assembly to the body with the 3 bolts.
Engage the clamp to install a new parking brake cable clamp.
Install the No. 3 parking brake cable assembly to the body.
Connect the No. 3 parking brake cable assembly to the backing plate with the bolt.
46430
2.INSTALL NO. 3 PARKING BRAKE CABLE ASSEMBLY (for Rear Disc Brake)
Install the No. 3 parking brake cable assembly to the rear axle beam assembly with the nut.
Install the No. 3 parking brake cable assembly to the body with the 3 bolts.
Engage the clamp to install a new parking brake cable clamp.
Install the No. 3 parking brake cable assembly to the body.
Engage the clip to install the No. 3 parking brake cable assembly to the rear disc brake cylinder assembly.
Be sure to engage the clip to the rear disc brake cylinder assembly.
Connect the No. 3 parking brake cable assembly to the rear disc brake cylinder assembly.
89516D
3.INSTALL SKID CONTROL SENSOR WIRE (w/ ABS,VSC)
Install the skid control sensor wire to the rear axle beam assembly with the nut.
4.INSTALL REAR BRAKE STRUT KIT (for Rear Drum Brake)
5.INSPECT REAR DRUM BRAKE (for Rear Drum Brake)
42403
6.INSTALL REAR BRAKE DRUM SUB-ASSEMBLY (for Rear Drum Brake)
7.ADJUST REAR DRUM BRAKE SHOE CLEARANCE (for Rear Drum Brake)
|
Expand |
Temporarily install the 2 wheel nuts.
Remove the shoe adjusting hole plug.
Turn the adjuster to expand the shoe until the drum locks.
|
Contract |
Hold the rear brake automatic adjust lever away from the adjuster, and contract the rear brake shoe by turning the adjust bolt using another screwdriver until the drum can rotate smoothly.
12 notches
Install the shoe adjusting hole plug.
Remove the 2 wheel nuts.
8.INSTALL REAR WHEEL (for Rear Drum Brake)
77641A
9.INSTALL NO. 1 FUEL TANK PROTECTOR (for RH Side)
for 1NR-FE:
Click hereEngine / Hybrid System>1NR-FE FUEL>FUEL TANK(for TMT Made)>INSTALLATION
for 2NR-FE:
Click hereEngine / Hybrid System>2NR-FE FUEL>FUEL TANK(for TMT Made)>INSTALLATION
for 1NZ-FE:
Click hereEngine / Hybrid System>1NZ-FE FUEL>FUEL TANK(for TMMIN Made)>INSTALLATION
for 2NZ-FE:
Click hereEngine / Hybrid System>2NZ-FE FUEL>FUEL TANK(for TMMIN Made)>INSTALLATION
58156
10.INSTALL FRONT NO. 4 FLOOR HEAT INSULATOR (for RH Side)
for 1NR-FE:
Click hereEngine / Hybrid System>1NR-FE FUEL>FUEL TANK(for TMT Made)>INSTALLATION
for 2NR-FE:
Click hereEngine / Hybrid System>2NR-FE FUEL>FUEL TANK(for TMT Made)>INSTALLATION
for 1NZ-FE:
Click hereEngine / Hybrid System>1NZ-FE FUEL>FUEL TANK(for TMMIN Made)>INSTALLATION
for 2NZ-FE:
Click hereEngine / Hybrid System>2NZ-FE FUEL>FUEL TANK(for TMMIN Made)>INSTALLATION
17410
11.INSTALL FRONT EXHAUST PIPE ASSEMBLY (for RH Side)
for Sedan 1NR-FE:
Click hereEngine / Hybrid System>1NR-FE FUEL>FUEL TANK(for TMT Made)>INSTALLATION
for Hatchback 1NR-FE:
Click hereEngine / Hybrid System>1NR-FE FUEL>FUEL TANK(for TMT Made)>INSTALLATION
for Sedan 2NR-FE:
Click hereEngine / Hybrid System>2NR-FE FUEL>FUEL TANK(for TMT Made)>INSTALLATION
for Hatchback 2NR-FE:
Click hereEngine / Hybrid System>2NR-FE FUEL>FUEL TANK(for TMT Made)>INSTALLATION
for 1NZ-FE:
Click hereEngine / Hybrid System>1NZ-FE INTAKE / EXHAUST>EXHAUST MANIFOLD>INSTALLATION
for 2NZ-FE:
Click hereEngine / Hybrid System>2NZ-FE INTAKE / EXHAUST>EXHAUST MANIFOLD>INSTALLATION
57533B
12.INSTALL FRONT FLOOR CENTER BRACE (for RH Side)
for 1NR-FE:
Click hereEngine / Hybrid System>1NR-FE INTAKE / EXHAUST>EXHAUST PIPE>INSTALLATION
for 2NR-FE:
Click hereEngine / Hybrid System>2NR-FE INTAKE / EXHAUST>EXHAUST PIPE>INSTALLATION
for 1NZ-FE:
Click hereEngine / Hybrid System>1NZ-FE INTAKE / EXHAUST>EXHAUST MANIFOLD>INSTALLATION
for 2NZ-FE:
Click hereEngine / Hybrid System>2NZ-FE INTAKE / EXHAUST>EXHAUST MANIFOLD>INSTALLATION
51405A
13.INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY (for RH Side w/ Metal Type Under Cover)
51451A
14.INSTALL CENTER ENGINE UNDER COVER (for RH Side w/ Metal Type Under Cover)
46430
15.CONNECT NO. 3 PARKING BRAKE CABLE ASSEMBLY
Engage the claw and 2 guides to install the parking brake cable end stopper to the parking brake equalizer.
Connect the No. 3 parking brake cable assembly to the parking brake equalizer.
16.ADJUST PARKING BRAKE LEVER TRAVEL
58910C
17.INSTALL REAR CONSOLE BOX ASSEMBLY (w/ Console Box Lid)
58910C
18.INSTALL REAR CONSOLE BOX ASSEMBLY (w/o Console Box Lid)