Perform "Inspection After Repair" after replacing the engine assembly.
Click hereEngine / Hybrid System>2NR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION
12372A
1.INSTALL ENGINE MOUNTING INSULATOR LH
Only perform this procedure when replacement of the engine mounting insulator LH is necessary.
| *a | Temporarily Tighten |
Engage the hook and temporarily install the engine mounting insulator LH to the vehicle.
Install the 5 bolts in the order shown in the illustration.
12305
2.INSTALL ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH
Only perform this procedure when replacement of the engine mounting insulator sub-assembly RH is necessary.
| *a | Temporarily Tighten |
Engage the hook and temporarily install the engine mounting insulator sub-assembly RH to the vehicle.
Install the 3 bolts in the order shown in the illustration.
3.REMOVE ENGINE STAND
Using a chain block and sling device, secure the engine assembly.
Make sure that the sling angle is correct to prevent the engine assembly and engine hangers from being damaged or deformed.
Remove the engine stand from the engine.
13405
4.INSTALL FLYWHEEL SUB-ASSEMBLY
Using height adjustable attachments or plate lift attachments, place the engine assembly on a flat, level surface.
Using height adjustable attachments or plate lift attachments, place the engine assembly horizontally.
Using an engine sling device and engine lifter, secure the engine assembly before servicing.
Using SST, hold the crankshaft pulley.
Install the flywheel sub-assembly to the crankshaft.
Clean the 8 bolts and their holes.
| *a | Adhesive |
Apply adhesive to 2 or 3 threads at the end of each of the 8 bolts.
Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent
To prevent contamination by foreign matter, install immediately after applying adhesive.
Install and uniformly tighten the 8 bolts in several steps, in the sequence shown in the illustration.
Do not start the engine for at least 1 hour after installing the flywheel sub-assembly.
31250
5.INSTALL CLUTCH DISC ASSEMBLY
31210
6.INSTALL CLUTCH COVER ASSEMBLY
31210
7.INSPECT AND ADJUST CLUTCH COVER ASSEMBLY
30300
8.INSTALL MANUAL TRANSAXLE ASSEMBLY
|
Clutch Spline Grease |
Apply clutch spline grease to the input shaft spline.
Toyota Genuine Clutch Spline Grease or equivalent
| *1 | Knock Pin |
Confirm that the 2 knock pins are installed on the engine assembly and are not damaged.
Align the input shaft with the clutch disc assembly and install the manual transaxle assembly to the engine assembly.
Make sure that the wire harness or similar items are not pinched between the contact surfaces.
Do not forcibly pry on the manual transaxle assembly.
When mounting the manual transaxle assembly to the engine assembly, make sure to securely fit the knock pins into the knock holes.
When tightening the bolts, be sure that the contact surfaces of the engine assembly and manual transaxle assembly are in close contact with one another.
Install the manual transaxle assembly to the engine assembly with the 8 bolts.
| Item | Length |
|---|---|
| Bolt A | 45 mm (1.77 in.) |
| Bolt B | 80 mm (3.15 in.) |
| Bolt C | 35 mm (1.38 in.) |
82121
9.INSTALL ENGINE WIRE
Connect all the engine wire connectors.
Connect the engine wire to the manual transaxle assembly with the bolt.
Connect the engine wire to the cylinder head cover sub-assembly with the 2 nuts.
Connect the engine wire to the cylinder head sub-assembly with the 2 bolts.
51201
10.TEMPORARILY TIGHTEN FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY
Temporarily tighten the front suspension crossmember sub-assembly to the engine moving control rod bracket with the through bolt.
11.REMOVE ENGINE HANGER
Remove the 2 bolts, No. 1 engine hanger and No. 2 engine hanger from the cylinder head sub-assembly.
11363A
12.INSTALL FLYWHEEL HOUSING SIDE COVER
28100
13.INSTALL STARTER ASSEMBLY
14.INSTALL ENGINE ASSEMBLY WITH MANUAL TRANSAXLE ASSEMBLY
Place height adjustment or plate lift attachments on an engine lifter, and then set the engine assembly with manual transaxle assembly.
Place the height adjustment or plate lift attachments so that the engine assembly with manual transaxle assembly is level.
As the engine assembly with manual transaxle assembly is very heavy, be sure to support it securely.
Operate the engine lifter and lift the engine assembly with transaxle and front suspension crossmember sub-assembly to the position where the engine mounting insulator sub-assembly RH and engine mounting insulator LH can be installed.
Do not raise the engine more than necessary. If the engine is raised excessively, the vehicle may also be lifted up.
Make sure that the engine is clear of all wiring and hoses.
Connect the engine mounting insulator LH to the engine mounting bracket LH with the through bolt and nut.
Tighten by holding the nut and turning the bolt.
Connect the engine mounting insulator sub-assembly RH to the engine mounting bracket RH with the bolt and 2 nuts.
Temporarily install the front suspension crossmember sub-assembly to the body with the 6 bolts.
By inserting SST into the datum holes in the front suspension crossmember RH and LH alternately, tighten bolts A, B and C on both sides to the specified torque, in several steps.
| *a | Datum Hole | *b | Correct |
| *c | Incorrect | - | - |
|
Front of Vehicle | - | - |
Insert SST into the datum hole vertically.
If impossible to insert SST vertically, loosen all bolts and then insert SST again.
Tighten the engine moving control rod bolt.
12144
15.INSTALL OIL PAN COVER SILENCER (w/ Metal Type Under Cover)
Perform this procedure only when replacement of the oil pan cover silencer is necessary.
| *a | Align RH Edge |
Align the RH edge of the oil pan cover silencer with the oil pan protector and attach it as shown in the illustration.
12137
16.INSTALL OIL PAN PROTECTOR (w/ Metal Type Under Cover)
Install the oil pan protector to the oil pan sub-assembly with the 3 bolts.
43498A
17.INSTALL NO. 1 DRIVE SHAFT HEAT INSULATOR
Temporarily tighten the No. 1 drive shaft heat insulator to the oil pan sub-assembly with the 2 bolts.
Fully tighten the 2 bolts, in the sequence shown in the illustration.
45025D
18.INSTALL NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY
45209
19.CONNECT STEERING SLIDING YOKE SUB-ASSEMBLY
45259A
20.INSTALL COLUMN HOLE COVER SILENCER SHEET
21.INSTALL FRONT DRIVE SHAFT ASSEMBLY
33820B
22.CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY
17410
23.INSTALL FRONT EXHAUST PIPE ASSEMBLY (for Sedan)
17410
24.INSTALL FRONT EXHAUST PIPE ASSEMBLY (for Hatchback)
57533B
25.INSTALL FRONT FLOOR CENTER BRACE
82121
26.CONNECT ENGINE WIRE
| *a | Top of the Vehicle |
Pass the engine wire through the hole to the outside of the engine room and engage the grommet to the vehicle as shown in the illustration.
Engage the clamp to connect the engine wire to the wire harness clamp bracket.
Engage the 2 clamps to connect the engine wire to the wire harness clamp bracket and vehicle.
Connect the 3 connectors.
Engage the 2 claws to connect the engine wire to the engine room relay block.
Install the nut to the engine room relay block.
Connect the connector to the engine room relay block.
Engage the clamp to connect the engine wire to the vehicle.
Connect the engine wire to the vehicle with the bolt.
Install the relay block cover to the engine room relay block.
55550
27.INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY
31470
28.INSTALL CLUTCH RELEASE CYLINDER ASSEMBLY
88320
29.INSTALL COOLER COMPRESSOR ASSEMBLY (w/ Cooler System)
Install the cooler compressor assembly to the cylinder block sub-assembly and oil pan sub-assembly with the 4 bolts, in the sequence shown in the illustration.
Connect the cooler compressor assembly connector.
23901
30.CONNECT FUEL TUBE SUB-ASSEMBLY
23841B
31.INSTALL EFI FUEL PIPE CLAMP
87245
32.CONNECT INLET HEATER WATER HOSE
| *a | View A |
| *b | Paint Mark |
| *c | Top of Vehicle |
| *d | Front of Vehicle |
Engage the clamp to connect the hose clamp to the wire harness clamp bracket.
Connect the inlet heater water hose to the cylinder head sub-assembly and slide the hose clip to secure it.
Perform the installation with the inlet heater water hose and hose clip at the correct angle.
87246
33.CONNECT OUTLET HEATER WATER HOSE
| *a | View A |
| *b | Paint Mark |
| *c | Top of Vehicle |
| *d | Front of Vehicle |
Connect the outlet heater water hose to the No. 1 water by-pass pipe and slide the hose clip to secure it.
Perform the installation with the outlet heater water hose and hose clip at the correct angle.
16572D
34.CONNECT NO. 2 RADIATOR HOSE
| *a | View A |
| *b | Paint Mark |
| *c | Top of Vehicle |
Connect the No. 2 radiator hose to the water inlet and slide the hose clip to secure it.
Perform the installation with the No. 2 radiator hose and hose clip at the correct angle.
16571C
35.CONNECT NO. 1 RADIATOR HOSE
| *a | View A |
| *b | Paint Mark |
| *c | Top of Vehicle |
Connect the No. 1 radiator hose to the cylinder head sub-assembly and slide the hose clip to secure it.
Perform the installation with the No. 1 radiator hose and hose clip at the correct angle.
Engage the clamp to connect the No. 1 radiator hose to the hose clamp.
44774
36.CONNECT UNION TO CONNECTOR TUBE HOSE
Connect the union to connector tube hose to the intake manifold and slide the hose clip to secure it.
27060
37.INSTALL GENERATOR WITH REGULATOR ASSEMBLY
38.INSTALL WIRE HARNESS CLAMP BRACKET
82121
39.CONNECT ENGINE WIRE
17167
40.INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR
11452
41.INSTALL OIL LEVEL DIPSTICK GUIDE
15301
42.INSTALL OIL LEVEL DIPSTICK SUB-ASSEMBLY
16361A
43.INSTALL FAN AND GENERATOR V BELT
74410
44.INSTALL BATTERY CARRIER ASSEMBLY
Install the battery carrier assembly to the engine mounting insulator LH and vehicle with the 5 bolts.
Engage the 4 clamps to connect the wire harness to the battery carrier assembly.
74431
45.INSTALL BATTERY TRAY
Install the battery tray to the battery carrier assembly.
28800
46.INSTALL BATTERY
| *1 | Battery Clamp Bolt |
| *2 | Battery Carrier |
| *3 | Engine Room Main Wire |
| *4 | Engine Wire |
Install the battery to the battery tray.
Install the battery clamp sub-assembly to the battery carrier assembly with the 2 nuts and battery clamp bolt.
Engage the hook of the battery clamp bolt to the notch of the battery carrier.
Engage the 2 claws to connect the engine room main wire to the engine wire.
Connect the engine room main wire with engine wire to the positive (+) battery terminal with the nut.
Install the terminal cover to the positive (+) battery terminal.
17701
47.INSTALL AIR CLEANER CASE SUB-ASSEMBLY
Install the air cleaner case sub-assembly to the air cleaner bracket with the 3 bolts.
Engage the clamp to install the engine wire to the air cleaner case sub-assembly.
17801
48.INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
Install the air cleaner filter element sub-assembly to the air cleaner case sub-assembly.
49.INSTALL AIR CLEANER CAP SUB-ASSEMBLY
Engage the 2 guides to install the air cleaner cap sub-assembly to the air cleaner case sub-assembly.
Engage the 2 clamps of the air cleaner cap sub-assembly.
Engage the 2 clamps to install the engine wire to the air cleaner cap sub-assembly.
Connect the mass air flow meter connector.
17880
50.INSTALL AIR CLEANER HOSE ASSEMBLY
12262
51.CONNECT NO. 2 VENTILATION HOSE
23827A
52.CONNECT NO. 2 FUEL VAPOR FEED HOSE
| *a | View A |
| *b | Hose Paint Mark |
| *c | Top of Vehicle |
Connect the No. 2 fuel vapor feed hose to the purge VSV (purge valve).
Perform the installation with the No. 2 fuel vapor feed hose at the correct angle.
23826
53.CONNECT NO. 1 FUEL VAPOR FEED HOSE
| *a | View A |
| *b | Hose Paint Mark |
| *c | Rear Side of Vehicle |
| *d | Top of Vehicle |
Connect the No. 1 fuel vapor feed hose to the purge VSV (purge valve) and slide the hose clip to secure it.
Perform the installation with the No. 1 fuel vapor feed hose at the correct angle.
54.INSTALL FRONT WHEELS
55.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
56.ADD ENGINE OIL
57.ADD ENGINE COOLANT
58.ADD MANUAL TRANSAXLE OIL
59.INSPECT FOR FUEL LEAK
60.CHECK ENGINE OIL LEVEL
61.INSPECT FOR ENGINE OIL LEAK
62.INSPECT FOR ENGINE COOLANT LEAK
63.INSPECT RESERVOIR TANK COOLANT LEVEL
64.INSPECT FOR MANUAL TRANSAXLE OIL LEAK
65.INSPECT FOR EXHAUST GAS LEAK
Perform "Inspection After Repairs" after repairing gas leaks in the exhaust system.
Click hereEngine / Hybrid System>2NR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION
66.INSPECT IGNITION TIMING
67.INSPECT ENGINE IDLING SPEED
68.INSPECT CO/HC
69.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT
51441C
70.INSTALL ENGINE UNDER COVER RH (w/o Metal Type Under Cover)
Install the engine under cover RH to the vehicle with the 2 bolts and 2 screws.
51442C
71.INSTALL ENGINE UNDER COVER LH (w/o Metal Type Under Cover)
Install the engine under cover LH to the vehicle with the 3 bolts and 5 screws.
51405A
72.INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY (w/ Metal Type Under Cover)
Install the No. 1 engine under cover sub-assembly to the vehicle with the 11 bolts.
51451A
73.INSTALL CENTER ENGINE UNDER COVER (w/ Metal Type Under Cover)
Install the center engine under cover to the vehicle with the 4 screws and 5 clips.
12611
74.INSTALL NO. 1 ENGINE COVER
75.CHECK FOR SPEED SENSOR SIGNAL