Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM › 2016.10–2017.10
RM30M0E _54 Brake _017098 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0090184 ANTI-LOCK BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  C1241  Low Power Supply Voltage Malfunction  


DESCRIPTION

If a malfunction is detected in the power supply circuit, the skid control ECU (brake actuator assembly) stores this DTC and the fail-safe function prohibits ABS operation.

This DTC is stored when the IG1 terminal voltage deviates from the DTC detection condition due to a malfunction in the power supply or charging circuit such as the battery or alternator circuit, etc.

The DTC is cleared when the IG1 terminal voltage returns to normal.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1241 Low Power Supply Voltage Malfunction Any of the following is detected:
1.

At a vehicle speed of 3 km/h (2 mph) or more, the IG1 terminal voltage is less than 9.5 V for 10 seconds or more.

2.

When the solenoid relay remains on and the IG1 terminal voltage is less than 9.5 V, the relay contact is open for 0.22 seconds or more.

3.

With the IG1 terminal voltage 9.5 V or less, the vehicle speed sensor power supply decreases for 60 seconds or more.

4.

When the motor fail-safe relay is on after the motor relay turns on, the IG1 terminal voltage is 9.5 V or less and the actuator pump drive motor is off for 0.12 seconds or more.


·

IG1 NO. 2 fuse

·

Battery

·

Charging system

·

Power source circuit

·

Internal power supply circuit of the skid control ECU (brake actuator assembly)



WIRING DIAGRAM

C353730E01
1.167,0.708 2.313,0.906 1.146,0.198 10 false from IG Circuit 3.417,0.885 4.167,1.083 0.75,0.198 10 false IG1 NO.2 5.156,0.708 5.49,0.906 0.333,0.198 10 false A35 5.156,1.969 5.49,2.167 0.333,0.198 10 false A35 5.479,0.708 5.813,0.906 0.333,0.198 10 false A47 5.479,1.979 5.813,2.177 0.333,0.198 10 false A47 5.833,0.719 6.167,0.917 0.333,0.198 10 false IG1 5.833,2 6.333,2.25 0.5,0.25 10 false GND1 5.208,0.51 5.458,0.677 0.25,0.167 10 false 34 5.51,0.51 5.76,0.677 0.25,0.167 10 false 34 5.24,1.781 5.49,1.948 0.25,0.167 10 false 1 5.552,1.781 5.802,1.948 0.25,0.167 10 false 1 5.5,2.583 7.083,3 1.583,0.417 10 false Skid Control ECU (Brake Actuator Assembly) 0.167,3.417 3.448,3.635 3.281,0.219 10 false *2: for LHD with Continuously Variable Transaxle 0.167,3.167 3.448,3.385 3.281,0.219 10 false *1: except LHD with Continuously Variable Transaxle 5.208,2.167 5.458,2.333 0.25,0.167 10 false *1 5.531,2.167 5.781,2.333 0.25,0.167 10 false *2 5.208,0.896 5.458,1.063 0.25,0.167 10 false *1 5.531,0.896 5.781,1.063 0.25,0.167 10 false *2

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

When replacing the skid control ECU (brake actuator assembly), perform reset memory, deceleration sensor zero point calibration and CVT oil pressure calibration (for CVT).




PROCEDURE

1.CHECK BATTERY
a.

Check the battery voltage.

Standard voltage:

11 to 14 V



Result:
Result Proceed to
OK A
NG (for 1NR-FE) B
NG (for 2NR-FE) C



A

2.CHECK HARNESS AND CONNECTOR (IG1 TERMINAL)

B

C

2.CHECK HARNESS AND CONNECTOR (IG1 TERMINAL)
a.
C353731C01
1.583,0.25 2,0.5 0.417,0.25 1.583,2.417 2,2.667 0.417,0.25 2.583,2.333 2.177,1.594 true 2.583,4.5 2.177,3.771 true 1.667,0.302 2.125,0.5 0.458,0.198 10 false A35 1.667,2.469 2.125,2.667 0.458,0.198 10 false A47 0.167,0.135 0.479,0.333 0.313,0.198 10 false *a 2.083,0.292 2.417,0.458 0.333,0.167 10 false *A 2.083,2.469 2.417,2.635 0.333,0.167 10 false *B 2.667,4.417 3.125,4.615 0.458,0.198 10 false IG1 2.667,2.25 3.125,2.448 0.458,0.198 10 false IG1
*A except LHD with Continuously Variable Transaxle
*B for LHD with Continuously Variable Transaxle
*a Front view of wire harness connector (to Skid Control ECU (Brake Actuator Assembly))


Make sure that there is no looseness at the locking part and the connecting part of the connector.


b.

Disconnect the skid control ECU (brake actuator assembly) connector.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
except LHD with Continuously Variable Transaxle
Tester Connection Switch Condition Specified Condition
A35-34 (IG1) - Body ground Ignition switch ON 11 to 14 V

for LHD with Continuously Variable Transaxle
Tester Connection Switch Condition Specified Condition
A47-34 (IG1) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (IG1 CIRCUIT)

3.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)
a.
C353731C02
1.583,0.25 2,0.5 0.417,0.25 1.583,2.417 2,2.667 0.417,0.25 0.75,0.5 1,1.177 true 0.75,2.667 1,3.385 true 1.667,0.302 2.125,0.5 0.458,0.198 10 false A35 1.667,2.469 2.125,2.667 0.458,0.198 10 false A47 0.167,0.135 0.479,0.333 0.313,0.198 10 false *a 2.083,0.292 2.417,0.458 0.333,0.167 10 false *A 2.083,2.469 2.417,2.635 0.333,0.167 10 false *B 0.542,0.302 1,0.5 0.458,0.198 10 false GND1 0.542,2.469 1,2.667 0.458,0.198 10 false GND1
*A except LHD with Continuously Variable Transaxle
*B for LHD with Continuously Variable Transaxle
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Turn the ignition switch off.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
except LHD with Continuously Variable Transaxle
Tester Connection Condition Specified Condition
A35-1 (GND1) - Body ground Always Below 1 Ω

for LHD with Continuously Variable Transaxle
Tester Connection Condition Specified Condition
A47-1 (GND1) - Body ground Always Below 1 Ω



c.

Reconnect the skid control ECU (brake actuator assembly) connector.


Result:
Proceed to
OK
NG



OK

4.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND1 CIRCUIT)

4.RECONFIRM DTC
a.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

Start the engine.


c.

Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.


d.

Check if the same DTC is recorded.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
DTC (C1241) is not output A
DTC (C1241) is output B


HINT:

If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE



A

B