Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM › 2016.10–2017.10
RM30M0E _54 Brake _017098 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0090184 ANTI-LOCK BRAKE SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  TC and CG Terminal Circuit  


DESCRIPTION

Connecting terminals 13 (TC) and 4 (CG) of the DLC3 causes the ECU to display the DTC by blinking the ABS warning light.

WIRING DIAGRAM

C353722E06
1.188,4.354 3,4.583 1.813,0.229 10 false : CAN Communication Line 0.521,3.302 0.917,3.469 0.396,0.167 10 false ECM 0.521,3.135 0.917,3.302 0.396,0.167 10 false F131 1.104,2.656 1.417,2.823 0.313,0.167 10 false TC 1.375,2.552 1.625,2.719 0.25,0.167 10 false 19 5.583,3.75 6,3.917 0.417,0.167 10 false DLC3 5.583,3.583 6,3.75 0.417,0.167 10 false F16 5.458,3 5.708,3.167 0.25,0.167 10 false 4 5.396,2.552 5.646,2.719 0.25,0.167 10 false 13 5.667,2.667 5.917,2.833 0.25,0.167 10 false TC 5.667,3.094 5.917,3.26 0.25,0.167 10 false CG 5.333,1.583 7,2.083 1.667,0.5 10 false Skid Control ECU (Brake Actuator Assembly)

HINT:

When the warning lights continue to blink, a ground short in the wiring of terminal 13(TC) of the DLC3 or an internal ground short in one or more ECUs is suspected.


CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake actuator assembly), perform reset memory, deceleration sensor zero point calibration and CVT oil pressure calibration (for CVT).



PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if CAN communication system DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM


Result:
Result Proceed to
DTC is not output A
DTC is output B



A

2.INSPECT DLC3

B

2.INSPECT DLC3
a.
C280109C39
1.542,0.146 1.917,0.417 0.375,0.271 1.604,0.813 1.177,0.396 true 1.844,1.5 1.438,1.865 true 0.104,0.083 0.417,0.24 0.313,0.156 10 false *1 0.938,0.302 1.25,0.5 0.313,0.198 10 false CG 1.229,1.802 1.5,2 0.271,0.198 10 false TC 1.615,0.208 1.906,0.365 0.292,0.156 10 false F16
*1 DLC3


Turn the ignition switch to ON.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F16-13 (TC) - F16-4 (CG) Ignition switch ON 11 to 14 V



Result:
Result Proceed to
NG A
OK B



A

3.CHECK HARNESS AND CONNECTOR (TC of DLC3 - ECM)

B

5.INSPECT ECM (TC of DLC3 INPUT)
3.CHECK HARNESS AND CONNECTOR (TC of DLC3 - ECM)
a.

Turn the ignition switch off.


b.

Disconnect the F131 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F16-13 (TC) - F131-19 (TC) Always Below 1 Ω
F16-13 (TC) or F131-19 (TC) - Body ground Always 10 kΩ or higher



d.

Reconnect the F131 ECM connector.


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (CG of DLC3 - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (CG of DLC3 - BODY GROUND)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F16-4 (CG) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.INSPECT ECM (TC of DLC3 INPUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT ECM (TC of DLC3 INPUT)
a.
C280109C40
1.542,0.146 1.917,0.417 0.375,0.271 1.604,0.813 1.177,0.396 true 1.844,1.5 1.438,1.865 true 0.104,0.083 0.417,0.24 0.313,0.156 10 false *1 0.938,0.302 1.25,0.5 0.313,0.198 10 false CG 1.229,1.802 1.5,2 0.271,0.198 10 false TC 1.615,0.208 1.906,0.365 0.292,0.156 10 false F16
*1 DLC3


Turn the ignition switch off.


b.

Using SST, connect terminals TC and CG of the DLC3.


SST
09843-18040  

c.

Turn the ignition switch to ON.


d.

Check that the malfunction indicator lamp is blinking.


Result:
Result Proceed to
MIL is blinking A
MIL is not blinking 1NR-FE B
2NR-FE C



A

B

C