Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › 2016.10–2017.10
RM30M0E _57 Power Source / Network _017152 NETWORKING _0084784 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Check CAN Bus Lines for Short Circuit (LHD Models)  


DESCRIPTION

There may be a short circuit between the V bus main lines and/or CAN branch lines when the resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is below 54 Ω.

Symptom Trouble Area
Resistance between terminals 6 (CANH) and 14 (CANL) of DLC3 is below 54 Ω.
·

Short in CAN main bus line

·

Short in CAN branch line

·

Combination meter assembly

·

Airbag ECU assembly*1

·

Brake actuator assembly*2

·

ECM

·

Certification ECU (smart key ECU assembly)*3

·

Air conditioning amplifier assembly

·

Spiral cable with sensor sub-assembly*4

·

No. 1 CAN junction connector



*1: w/ Airbag System

*2: w/ ABS

*3: w/ Smart Entry and Start System

*4: w/ VSC


WIRING DIAGRAM

E351545E01
0.094,0.083 1.01,0.281 0.917,0.198 10 false V Bus: 0.333,0.5 1.75,0.75 1.417,0.25 10 false x: Suspected Area 3.365,0.26 4.135,0.458 0.771,0.198 10 false 120 Ω 4.552,0.521 5.323,0.719 0.771,0.198 10 false ECM 2.667,0.885 3.438,1.083 0.771,0.198 10 false CANL 4.063,0.885 4.833,1.083 0.771,0.198 10 false CANH 2.844,1.094 3.156,1.292 0.313,0.198 10 false 14 2.844,2.021 3.156,2.219 0.313,0.198 10 false 14 4.094,1.094 4.406,1.292 0.313,0.198 10 false 13 4.094,2.021 4.406,2.219 0.313,0.198 10 false 3 4.552,0.354 5.323,0.552 0.771,0.198 10 false F130 2.813,1.542 3.125,1.74 0.313,0.198 10 false W 4.167,1.542 4.479,1.74 0.313,0.198 10 false BE 2.688,2.24 3,2.438 0.313,0.198 10 false 4 2.615,2.594 2.927,2.792 0.313,0.198 10 false 15 2.688,3.698 3,3.896 0.313,0.198 10 false 2 2.615,4.052 2.927,4.25 0.313,0.198 10 false 13 1.781,2.24 2.094,2.438 0.313,0.198 10 false 13 1.781,2.594 2.094,2.792 0.313,0.198 10 false 22 1.781,3.698 2.094,3.896 0.313,0.198 10 false 25 1.781,4.052 2.094,4.25 0.313,0.198 10 false 14 1.26,2.594 2.031,2.792 0.771,0.198 10 false CANL 1.26,4.052 2.031,4.25 0.771,0.198 10 false CANL 1.25,2.24 2.021,2.438 0.771,0.198 10 false CANH 1.25,3.698 2.021,3.896 0.771,0.198 10 false CANH 2.24,2.177 2.552,2.375 0.313,0.198 10 false B 2.219,2.542 2.531,2.74 0.313,0.198 10 false W 2.219,3.99 2.531,4.188 0.313,0.198 10 false W 2.24,3.625 2.552,3.823 0.313,0.198 10 false L 0.25,3.031 1.021,3.229 0.771,0.198 10 false F21 0.25,3.198 1.969,3.448 1.719,0.25 10 false Airbag ECU Assembly*1 0.146,4.646 1.865,4.896 1.719,0.25 10 false Brake Actuator Assembly*2 0.146,4.479 2.01,4.708 1.865,0.229 10 false A49*3, A48*4, A47*5, A35*6 4.323,2.969 4.635,3.167 0.313,0.198 10 false 7 4.323,3.323 4.635,3.521 0.313,0.198 10 false 18 4.323,4.417 4.635,4.615 0.313,0.198 10 false 8 4.323,4.781 4.635,4.979 0.313,0.198 10 false 19 4.771,3.26 5.083,3.458 0.313,0.198 10 false W 4.771,4.719 5.083,4.917 0.313,0.198 10 false W 4.792,2.906 5.104,3.104 0.313,0.198 10 false L 4.792,4.365 5.104,4.563 0.313,0.198 10 false V 5.177,2.969 5.49,3.167 0.313,0.198 10 false 40 5.177,3.323 5.49,3.521 0.313,0.198 10 false 18 5.177,4.427 5.49,4.625 0.313,0.198 10 false 11 5.177,4.781 5.49,4.979 0.313,0.198 10 false 12 5.479,2.969 6.25,3.167 0.771,0.198 10 false CANH 5.479,3.323 6.25,3.521 0.771,0.198 10 false CANL 5.479,4.427 6.25,4.625 0.771,0.198 10 false TX+ 5.479,4.781 6.25,4.979 0.771,0.198 10 false TX- 5.083,3.594 5.854,3.792 0.771,0.198 10 false F44 5.083,3.76 6.938,4.177 1.854,0.417 10 false Certification ECU (Smart Key ECU Assembly)*7 5.313,5.385 6.906,5.854 1.594,0.469 10 false Air Conditioning Amplifier Assembly 5.313,5.219 6.229,5.479 0.917,0.26 10 false F3*8, F124*9 0.271,5.5 2.833,5.75 2.563,0.25 10 false *1: w/ Airbag System 0.271,5.833 2.833,6.083 2.563,0.25 10 false *2: w/ ABS 0.271,6.167 2.833,6.417 2.563,0.25 10 false *3: w/ VSC with CVT 0.271,6.5 2.833,6.75 2.563,0.25 10 false *4: w/ VSC except CVT 0.271,6.833 2.833,7.083 2.563,0.25 10 false *5: w/o VSC with CVT 0.271,7.167 2.833,7.417 2.563,0.25 10 false *6: w/o VSC except CVT 0.271,7.5 2.833,7.75 2.563,0.25 10 false *7: w/ Smart Entry and Start System 0.271,7.833 3.188,8.073 2.917,0.24 10 false *8: for Automatic Air Conditioning System 0.271,8.167 2.833,8.417 2.563,0.25 10 false *9: for Manual Air Conditioning System 4.885,7.094 7,7.333 2.115,0.24 10 false : CAN Main Bus Line (CANH) 4.896,7.49 6.969,7.719 2.073,0.229 10 false : CAN Main Bus Line (CANL) 4.906,7.896 7.042,8.156 2.135,0.26 10 false : CAN Branch Line (CANH) 4.906,8.292 7.094,8.542 2.188,0.25 10 false : CAN Branch Line (CANL) 4.323,2.219 5.094,2.417 0.771,0.198 10 false F62 4.323,2.385 6.552,2.635 2.229,0.25 10 false No. 1 CAN Junction Connector

E340834E01
1.229,0.896 1.844,1.094 0.615,0.198 10 false CANH 0.146,0.094 1.25,0.333 1.104,0.24 10 false V Bus: 0.208,0.427 3.333,0.667 3.125,0.24 10 false x: Suspected Area 1.26,1.229 1.875,1.427 0.615,0.198 10 false CANL 1.76,0.885 1.917,1.083 0.156,0.198 10 false 4 1.76,1.25 1.917,1.448 0.156,0.198 10 false 3 2.229,0.802 2.385,1 0.156,0.198 10 false R 2.219,1.177 2.375,1.375 0.156,0.198 10 false W 2.698,0.875 2.854,1.073 0.156,0.198 10 false 9 2.656,1.229 2.969,1.427 0.313,0.198 10 false 20 0.292,1.677 0.75,1.875 0.458,0.198 10 false F116 0.292,1.823 1.823,2.385 1.531,0.563 10 false Spiral Cable with Sensor Sub-assembly*1 2.833,2.719 2.99,2.917 0.156,0.198 10 false W 4.771,1.875 4.927,2.073 0.156,0.198 10 false W 5.885,1.667 6.5,1.865 0.615,0.198 10 false CANH 6,2 6.615,2.198 0.615,0.198 10 false CANL 6.167,2.25 6.625,2.448 0.458,0.198 10 false F16 6.167,2.385 6.781,2.583 0.615,0.198 10 false DLC3 4.75,1.49 5.063,1.688 0.313,0.198 10 false GR 4.302,1.552 4.458,1.75 0.156,0.198 10 false 1 4.271,1.917 4.583,2.115 0.313,0.198 10 false 12 4.094,2.469 4.25,2.667 0.156,0.198 10 false 6 4.083,3 4.396,3.198 0.313,0.198 10 false 32 2.896,2.448 3.208,2.646 0.313,0.198 10 false 17 2.885,2.99 3.198,3.188 0.313,0.198 10 false 31 2.667,3.208 3.281,3.406 0.615,0.198 10 false CANL 4.083,3.208 4.698,3.406 0.615,0.198 10 false CANH 4.125,2.688 4.333,2.917 0.208,0.229 10 false G 5.646,1.573 5.802,1.771 0.156,0.198 10 false 6 5.667,1.938 5.979,2.135 0.313,0.198 10 false 14 4.583,3.417 5.042,3.615 0.458,0.198 10 false F38 4.583,3.583 6.479,3.948 1.896,0.365 10 false Combination Meter Assembly 3.313,3.771 4.083,3.969 0.771,0.198 10 false 120 Ω 4.927,4.219 6.833,4.458 1.906,0.24 10 false : CAN Main Bus Line (CANH) 4.927,4.594 6.833,4.833 1.906,0.24 10 false : CAN Main Bus Line (CANL) 4.927,5.01 7,5.25 2.073,0.24 10 false : CAN Branch Bus Line (CANH) 4.917,5.417 6.99,5.656 2.073,0.24 10 false : CAN Branch Bus Line (CANL) 0.458,5.417 1.99,5.615 1.531,0.198 10 false *1: w/ VSC 4.354,0.635 4.813,0.833 0.458,0.198 10 false F62 4.354,0.792 6.25,1.115 1.896,0.323 10 false No.1 CAN Junction Connector

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the ignition switch to ON and wait at least 60 seconds, and then drive the vehicle at a speed of 36 km/h (22 mph) or more for 3.74 seconds or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM



HINT:
·

Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR SHORT IN CAN BUS LINES (COMBINATION METER ASSEMBLY - NO. 1 CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) battery terminal.


b.
E221291C37
1.5,0.25 1.917,0.5 0.417,0.25 1.781,1.385 1.552,1.771 true 1.906,1.396 2.104,1.75 true 1.604,0.292 2.083,0.51 0.479,0.219 10 false F38 0.073,0.052 0.281,0.26 0.208,0.208 10 false *a 1.365,1.802 1.792,2.042 0.427,0.24 10 false CANL 1.938,1.792 2.375,2.031 0.438,0.24 10 false CANH
*a Front view of wire harness connector
(to Combination Meter Assembly)


Disconnect the combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F38-32 (CANH) - F38-31 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

2.CHECK FOR SHORT IN CAN BUS LINES (ECM - NO. 1 CAN JUNCTION CONNECTOR)
2.CHECK FOR SHORT IN CAN BUS LINES (ECM - NO. 1 CAN JUNCTION CONNECTOR)
a.

Reconnect the F38 combination meter assembly connector.


b.
C343963C18
1.406,0.083 1.906,0.333 0.5,0.25 2.5,1.833 2.083,1.146 true 1.583,1.833 1.948,1.167 true 0.104,0.083 0.417,0.24 0.313,0.156 10 false *a 1.5,0.125 1.948,0.333 0.448,0.208 10 false F130 1.365,1.875 1.813,2.083 0.448,0.208 10 false CANH 2.344,1.875 2.792,2.083 0.448,0.208 10 false CANL
*a Front view of wire harness connector
(to ECM)


Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F130-13 (CANH) - F130-14 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Result Proceed to
OK (for 1NR-FE) A
OK (for 2NR-FE) B
NG C



A

B

C

3.CHECK FOR SHORT IN CAN BUS LINES (NO. 1 CAN JUNCTION CONNECTOR)
3.CHECK FOR SHORT IN CAN BUS LINES (NO. 1 CAN JUNCTION CONNECTOR)
a.

Reconnect the F81*1, F82*2 or F130*3 ECM connector.

*1: for 2NZ-FE with Manual Transaxle

*2: for Automatic Transaxle

*3: for 1NR-FE or 2NR-FE



b.
C287156C04
1.417,0.583 1.917,0.833 0.5,0.25 0.677,1.354 1.26,1.719 true 0.667,1.573 1.115,1.719 true 0.677,1.813 0.938,1.813 true 0.667,2.052 0.927,1.99 true 0.646,2.344 1.115,2.063 true 0.688,2.625 1.292,2.063 true 1.438,1.719 1.99,0.802 true 1.74,1.74 2.115,1.052 true 1.74,2.052 1.948,2.49 true 1.427,2.052 1.625,2.677 true 1.865,2.052 2.75,2.5 true 1.979,2.042 2.833,2.25 true 2,1.729 2.833,1.417 true 1.854,1.729 2.75,1.167 true 2.146,1.75 2.833,1.667 true 2.146,2.042 2.833,2 true 0.135,1.719 0.75,1.917 0.615,0.198 10 false CANH*b 0.135,1.25 0.75,1.448 0.615,0.198 10 false CANH*d 0.135,1.49 0.75,1.688 0.615,0.198 10 false CANH*c 0.135,1.969 0.75,2.167 0.615,0.198 10 false CANL*b 0.135,2.25 0.75,2.448 0.615,0.198 10 false CANL*c 0.135,2.552 0.75,2.75 0.615,0.198 10 false CANL*d 2.063,0.708 2.677,0.906 0.615,0.198 10 false CANH*e 2,2.427 2.615,2.625 0.615,0.198 10 false CANL*f 1.698,2.646 2.313,2.844 0.615,0.198 10 false CANL*e 1.542,0.625 2,0.823 0.458,0.198 10 false F62 2.167,0.969 2.781,1.167 0.615,0.198 10 false CANH*f 0.063,0.042 0.375,0.24 0.313,0.198 10 false *a 2.823,1.063 3.396,1.271 0.573,0.208 10 false CANH*g 2.823,2.406 3.385,2.604 0.563,0.198 10 false CANL*g 2.865,1.323 3.427,1.531 0.563,0.208 10 false CANH*h 2.885,2.156 3.427,2.365 0.542,0.208 10 false CANL*h 2.865,1.573 3.427,1.781 0.563,0.208 10 false CANH*i 2.885,1.906 3.427,2.115 0.542,0.208 10 false CANL*i
*a Front view of wire harness connector
(to No. 1 CAN Junction Connector)
*b to DLC3
*c to Brake Actuator Assembly*1
*d to ECM
*e to Airbag ECU Assembly*2
*f to Combination Meter Assembly
*g to Certification ECU (Smart Key ECU Assembly)*3
*h to Air Conditioning Amplifier Assembly
*i to Spiral Cable with Sensor Sub-assembly*4


Disconnect the No. 1 CAN junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
F62-1 (CANH) - F62-12 (CANL) Cable disconnected from negative (-) battery terminal 1 MΩ DLC3
F62-2 (CANH) - F62-13 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Brake actuator assembly*1
F62-3 (CANH) - F62-14 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω ECM
F62-4 (CANH) - F62-15 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Airbag ECU assembly*2
F62-6 (CANH) - F62-17 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω Combination meter assembly
F62-7 (CANH) - F62-18 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Certification ECU (smart key ECU assembly)*3
F62-8 (CANH) - F62-19 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Air conditioning amplifier assembly
F62-9 (CANH) - F62-20 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Spiral cable with sensor sub-assembly*4


*1: w/ ABS

*2: w/ Airbag System

*3: w/ Smart Entry and Start System

*4: w/ VSC



Result:
Result Proceed to
OK A
NG (ECM main line) B
NG (ECU or sensor branch line) C
NG (Combination meter assembly main line) D
NG (DLC3 branch line) E



A

REPLACE NO. 1 CAN JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (ECM - NO. 1 CAN JUNCTION CONNECTOR)

C

4.CHECK FOR SHORT IN CAN BUS LINES (ECU, SENSOR)

D

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (COMBINATION METER ASSEMBLY - NO. 1 CAN JUNCTION CONNECTOR)

E

REPAIR OR REPLACE CAN BRANCH LINE CONNECTED DLC3

4.CHECK FOR SHORT IN CAN BUS LINES (ECU, SENSOR)
a.

Reconnect the F62 No. 1 CAN junction connector.


b.

Disconnect the connector that includes terminals CANH and CANL from the ECU (or sensor) to which the short circuited branch line is connected.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>TERMINALS OF ECU


c.
C152423C12
1.427,0.167 1.854,0.427 0.427,0.26 1.938,0.927 2.354,0.417 true 1.938,1.438 1.49,1.844 true 0.073,0.083 0.385,0.24 0.313,0.156 10 false *1 1.51,0.198 1.969,0.396 0.458,0.198 10 false F16 2.417,0.292 3.031,0.49 0.615,0.198 10 false CANH 1.094,1.792 1.708,1.99 0.615,0.198 10 false CANL
*1 DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F16-6 (CANH) - F16-14 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω


HINT:

If the resistance becomes normal (between 54 and 69 Ω) when the connector is disconnected from the ECU (or sensor), there may be a short in the ECU (or sensor).



Result:
Result
OK
NG



OK

REPLACE CORRESPONDING ECU OR SENSOR

NG

REPAIR OR REPLACE CORRESPONDING ECU OR SENSOR BRANCH LINES OR CONNECTOR