Home › Vehicle Interior › INTERIOR PANELS / TRIM › INSTRUMENT PANEL SAFETY PAD › 2017.10–2018.01
RM30M0E _58 Vehicle Interior _017120 INTERIOR PANELS / TRIM _0089077 INSTRUMENT PANEL SAFETY PAD A

INTERIOR PANELS / TRIM  INSTRUMENT PANEL SAFETY PAD  REMOVAL  


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


Hide 62111C 4.REMOVE COWL SIDE TRIM BOARD RH

HINT:

Use the same procedure as for the LH side.


Hide 62312B 5.DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH

a.

Disconnect the front door opening trim weatherstrip LH.


Hide 62311B 6.DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP RH

HINT:

Use the same procedure as for the LH side.


Hide 62211 8.REMOVE FRONT PILLAR GARNISH RH

HINT:

Use the same procedure as for the LH side.


Hide 55412D 9.REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL (w/ Radio Receiver)

B346841

a.

Disengage the 7 clips and the 6 claws.


b.

Disconnect the connector and remove the center instrument cluster finish panel.


Hide 55412D 10.REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL (w/o Radio Receiver)

a.
B346842

Disengage the 7 clips.


b.

Disconnect the connector and remove the center instrument cluster finish panel.


Hide 11.REMOVE RADIO RECEIVER ASSEMBLY WITH BRACKET (w/ Radio Receiver)

Hide 12.REMOVE RADIO TUNER OPENING COVER WITH BRACKET (w/o Radio Receiver)

a.
B346843

Remove the 4 screws.


b.

Disengage the 2 guides and remove the radio tuner opening cover with bracket.


Hide 55606 13.REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

B346844

a.

Remove the 3 screws <C>.


b.

Disengage the claw and the guide and remove the No. 1 instrument panel under cover sub-assembly.


Hide 55432B 14.REMOVE LOWER INSTRUMENT PANEL FINISH PANEL

a.
B346845

Disengage the 5 clips and the 2 claws.


b.

Disconnect the connectors and remove the lower instrument panel finish panel.


Hide 55411G 15.REMOVE NO. 1 INSTRUMENT CLUSTER FINISH PANEL

a.
B346846C01
0.656,0.385 0.969,0.583 0.313,0.198 10 false *a 2.292,0.125 2.604,0.323 0.313,0.198 10 false *a
*a 170 mm (6.69 in)
V100155

Protective Tape


Apply protective tape as shown in the illustration.


b.

Using a moulding remover, pry up on the No. 1 instrument cluster finish panel until there is enough of a gap to make it possible to pull on the panel by hand.


c.
B346847

Pull the No. 1 instrument cluster finish panel in the direction indicated by the arrow to disengage the 12 clips and the 2 claws and the 4 guides and remove the No. 1 instrument cluster finish panel as shown in the illustration.


Hide 16.REMOVE UPPER CENTER INSTRUMENT CLUSTER FINISH PANEL

a.
B346848

Disengage the 3 claws and the clip and remove the upper center instrument cluster finish panel.


Hide 84140 17.REMOVE HEADLIGHT DIMMER SWITCH ASSEMBLY

Hide 55474C 18.REMOVE NO. 1 INSTRUMENT CLUSTER FINISH PANEL GARNISH

a.
B346849

Pull the instrument panel cup holder sub-assembly in the direction indicated by the arrow.


b.

Disengage the 2 claws and the 2 clips and remove the No. 1 instrument cluster finish panel garnish.


Hide 55650 19.REMOVE NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY

a.
B346850

Disengage the 3 claws and the 2 clips and remove the No. 1 instrument panel register assembly.


Hide 55604A 20.REMOVE INSTRUMENT PANEL CUP HOLDER SUB-ASSEMBLY (for Driver Side)

B346917C01
1.615,1.25 1.948,1.25 false 1.469,1.156 1.781,1.354 0.313,0.198 10 false *a
*a Protective Tape


a.

Using a screwdriver with its tip wrapped in protective tape, disengage the 2 claws and remove the instrument panel cup holder sub-assembly.


Hide 55410C 21.REMOVE INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY

a.
B346852

Disengage the 4 clips and the 2 claws and remove the instrument cluster finish panel assembly.


Hide 83100 22.REMOVE COMBINATION METER ASSEMBLY

Hide 55550 23.REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY

a.
B346853

Slightly bend 2 stoppers in the directions indicated by the arrows in the illustration and pull the glove compartment door assembly until the stoppers are released.


b.
B346854

Open the glove compartment door assembly to approximately 47° from its closed position. Pull it horizontally in the direction indicated by the arrow to disengage the 2 hinges and remove the glove compartment door assembly.

NOTICE:
·

Pulling the glove compartment door assembly upward to remove it causes the hinges to deform.

·

Be sure to pull out the glove compartment door assembly horizontally.




Hide 55607 24.REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

a.
B346855

Disengage the 3 claws and the guide and remove the No. 2 instrument panel under cover sub-assembly.


Hide 55900 25.REMOVE AIR CONDITIONING CONTROL ASSEMBLY (for Automatic Air Conditioning System)

Hide 55902C 26.REMOVE AIR CONDITIONING PANEL SUB-ASSEMBLY (for Manual Air Conditioning System)

Hide 55900A 27.REMOVE HEATER CONTROL AND ACCESSORY ASSEMBLY (for Manual Air Conditioning System)

Hide 55604B 28.REMOVE INSTRUMENT PANEL CUP HOLDER SUB-ASSEMBLY (for Front Passenger Side)

B346856

a.

Pull the instrument panel cup holder sub-assembly in the direction indicated by the arrow.


b.

Disengage the 2 claws and remove the instrument panel cup holder sub-assembly.


Hide 55475A 29.REMOVE NO. 2 INSTRUMENT CLUSTER FINISH PANEL GARNISH

B346857

a.

Disengage the 6 claws and the 4 clips and remove the No. 2 instrument cluster finish panel garnish.


Hide 55660 30.REMOVE NO. 2 INSTRUMENT PANEL REGISTER ASSEMBLY

a.
B346858

Disengage the 7 claws and the clip and remove the No. 2 instrument panel register assembly.


Hide 82142A 32.DISCONNECT INSTRUMENT PANEL WIRE

a.
B346859C01
0.729,2.542 1.021,2.25 false 1.031,2.104 1.344,2.302 0.313,0.198 10 false *1
*1 Slider


Slide the slider to release the lock, and then disconnect the connector.

NOTICE:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.



Hide 53601 33.DISCONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY

a.
B346785

Disengage the claw and the 3 guides and disconnect the hood lock control lever sub-assembly.


Hide 55301 34.REMOVE INSTRUMENT PANEL SUB-ASSEMBLY

a.

Disconnect the connectors.


b.

Disengage the clamps.


c.

for Automatic Air Conditioning System:

i.

Disconnect the cooler thermistor hose.



d.

Remove the 4 bolts <A>, 2 bolts <E>, bolt <D> and 2 screws <B>.

B346861E01
2.104,1.375 2.448,1.552 0.344,0.177 10 true <A> 5.188,1.792 5.531,1.969 0.344,0.177 10 true <A> 6.083,1.844 6.427,2.021 0.344,0.177 10 true <A> 4.281,4.156 4.625,4.333 0.344,0.177 10 false <B> 0.083,4.031 0.427,4.208 0.344,0.177 10 false <E> 2.927,4.146 3.271,4.323 0.344,0.177 10 false <A> 4.729,3.781 5.073,3.958 0.344,0.177 10 false <D> 5.469,3.917 5.813,4.094 0.344,0.177 10 false <B> 6.813,4 7.156,4.177 0.344,0.177 10 false <E>


e.

Remove the 2 clips.


f.

Disengage the 9 guides and remove the instrument panel sub-assembly.

B346862