Home › Engine / Hybrid System › CRUISE CONTROL › CRUISE CONTROL SYSTEM › from 2017.10
RM30M0E _51 Engine / Hybrid System _052909 CRUISE CONTROL _0256264 CRUISE CONTROL SYSTEM C

CRUISE CONTROL  CRUISE CONTROL SYSTEM  P0571  Brake Switch "A" Circuit  


DESCRIPTION

When the brake pedal is depressed, the stop light switch assembly sends a signal to the ECM. When the ECM receives this signal, it cancels cruise control system control of vehicle speed. The fail-safe function operates to enable normal driving even if there is a malfunction in the stop light signal circuit. The cancellation condition occurs when voltage is applied to terminal STP. When the brake is applied, voltage is normally applied to terminal STP of the ECM through the STOP fuse and the stop light switch assembly, and the ECM cancels control of vehicle speed by the cruise control system.

DTC No. Detection Item DTC Detection Condition Trouble Area
P0571 Brake Switch "A" Circuit When voltage of STP terminal and that of ST1- terminal of ECM are less than 1 V for 0.5 sec. or more
·

Stop light switch assembly

·

Stop light switch circuit

·

ECM

·

Harness or connector



WIRING DIAGRAM

B253741E14
6.052,2.792 6.448,2.969 0.396,0.177 10 false F131 6.052,2.969 7.156,3.146 1.104,0.177 10 false ECM 3.656,2.563 4.052,2.74 0.396,0.177 10 false A58 3.656,2.719 5.427,2.896 1.771,0.177 10 false Stop Light Switch Assembly 6.063,1.563 6.458,1.76 0.396,0.198 10 false ST1- 6.063,0.844 6.458,1.042 0.396,0.198 10 false STP 5.802,1.458 5.99,1.656 0.188,0.198 10 false 11 5.813,0.729 6.031,0.958 0.219,0.229 10 false 10 2.323,1.76 3.073,1.99 0.75,0.229 10 false IG2 NO. 1 2.448,1.031 2.875,1.208 0.427,0.177 10 false STOP 4.313,0.854 4.708,1.063 0.396,0.208 10 false OUT 4.51,1.573 4.656,1.771 0.146,0.198 10 false L 3.833,2.073 4.188,2.271 0.354,0.198 10 false GND 4.719,1.448 4.844,1.646 0.125,0.198 10 false 4 4.719,0.74 4.844,0.938 0.125,0.198 10 false 2 3.646,1.948 3.771,2.146 0.125,0.198 10 false 3 3.854,1.573 4.01,1.771 0.156,0.198 10 false B 3.646,1.469 3.771,1.667 0.125,0.198 10 false 5 3.854,0.844 4.01,1.042 0.156,0.198 10 false B 3.646,0.74 3.771,0.938 0.125,0.198 10 false 1 0.083,0.063 1.979,0.271 1.896,0.208 12 false for LED Type Stop Light: 0.365,1.594 1.344,1.771 0.979,0.177 10 false from IG Circuit 0.49,0.844 1.302,1.031 0.813,0.188 10 false from Battery

C378886E01
0.094,0.063 2.063,0.323 1.969,0.26 12 false for Bulb Type Stop Light: 0.646,0.74 1.563,0.979 0.917,0.24 10 false from Battery 0.51,1.542 1.563,1.792 1.052,0.25 10 false from IG Circuit 2.031,0.927 2.646,1.125 0.615,0.198 10 false STOP 1.906,1.708 2.625,1.927 0.719,0.219 10 false IG2 NO. 1 2.708,2.177 4.573,2.438 1.865,0.26 10 false Stop Light Switch Assembly 2.969,0.635 3.125,0.833 0.156,0.198 10 false B 3.844,0.635 4,0.833 0.156,0.198 10 false L 3.844,1.438 4,1.635 0.156,0.198 10 false L 2.969,1.427 3.125,1.625 0.156,0.198 10 false B 5.698,2.156 6.313,2.354 0.615,0.198 10 false ECM 5.406,0.635 5.708,0.844 0.302,0.208 10 false 10 5.417,1.438 5.719,1.646 0.302,0.208 10 false 11 5.688,0.75 6.156,0.969 0.469,0.219 10 false STP 5.677,1.542 6.146,1.76 0.469,0.219 10 false ST1- 2.75,0.625 3.052,0.833 0.302,0.208 10 false 2 4.052,0.625 4.354,0.833 0.302,0.208 10 false 1 2.75,1.427 3.052,1.635 0.302,0.208 10 false 4 4.052,1.427 4.354,1.635 0.302,0.208 10 false 3 2.719,2.01 3.021,2.219 0.302,0.208 10 false A21 5.698,1.99 6.313,2.188 0.615,0.198 10 false F131

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (POWER SOURCE)
a.
C360768C03
1.531,0.198 1.948,0.448 0.417,0.25 0.938,1.76 1.365,1.281 true 2.271,1.75 2.042,1.292 true 1.583,1.771 1.688,1.26 true 0.115,0.125 0.427,0.323 0.313,0.198 10 false *a 1.615,0.229 1.927,0.427 0.313,0.198 10 false A58 0.865,1.792 1.177,1.99 0.313,0.198 10 false B 2.26,1.781 2.573,1.979 0.313,0.198 10 false B 1.427,1.802 1.854,2 0.427,0.198 10 false GND
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


for LED Type Stop Light

i.

Disconnect the stop light switch assembly connector.


ii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A58-1 (B) - Body ground Always 11 to 14 V
A58-5 (B) - Body ground Ignition switch ON 11 to 14 V



iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A58-3 (GND) - Body ground Always Below 1 Ω




b.
E144327C12
0.396,1.958 0.833,2.302 0.438,0.344 1.865,2.063 2.396,1.354 true 1.906,2.552 2.323,2.896 true 0.5,2.031 1.104,2.448 0.604,0.417 10 false A21 0.24,0.177 0.656,0.573 0.417,0.396 10 false *a 2.448,1.229 2.667,1.438 0.219,0.208 10 false B 2.375,2.813 2.594,3.021 0.219,0.208 10 false B
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


for Bulb Type Stop Light

i.

Disconnect the stop light switch assembly connector.


ii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A21-2 (B) - Body ground Always 11 to 14 V
A21-4 (B) - Body ground Ignition switch ON 11 to 14 V




c.

Reconnect the stop light switch assembly connector.


Result:
Proceed to
OK
NG



OK

2.INSPECT STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.

for LED Type Stop Light

i.

Inspect the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>ON-VEHICLE INSPECTION



b.

for Bulb Type Stop Light

i.

Remove the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>REMOVAL


ii.

Inspect the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSPECTION



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (ECM - STOP LIGHT SWITCH ASSEMBLY)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (ECM - STOP LIGHT SWITCH ASSEMBLY)
a.

Disconnect the F131 ECM connector.


b.

for LED Type Stop Light

i.

Disconnect the A58 stop light switch assembly connector.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
F131-10 (STP) - A58-2 (OUT) Always Below 1 Ω
F131-11 (ST1-) - A58-4 (L) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
F131-10 (STP) or A58-2 (OUT) - Body ground Always 10 kΩ or higher
F131-11 (ST1-) or A58-4 (L) - Body ground Always 10 kΩ or higher




c.

for Bulb Type Stop Light

i.

Disconnect the A21 stop light switch assembly connector.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
F131-10 (STP) - A21-1 (L) Always Below 1 Ω
F131-11 (ST1-) - A21-3 (L) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
F131-10 (STP) or A21-1 (L) - Body ground Always 10 kΩ or higher
F131-11 (ST1-) or A21-3 (L) - Body ground Always 10 kΩ or higher




Result:
Result Proceed to
OK (for 1NR-FE) A
OK (for 2NR-FE) B
NG C


d.

Reconnect the stop light switch assembly connector.


e.

Reconnect the ECM connector.



A

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR