Home › Vehicle Interior › SEAT BELT › OCCUPANT DETECTION SENSOR › from 2017.10
RM30M0E _58 Vehicle Interior _017117 SEAT BELT _0333431 OCCUPANT DETECTION SENSOR A

SEAT BELT  OCCUPANT DETECTION SENSOR  INSTALLATION  


CAUTION / NOTICE / HINT

CAUTION:
·

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION

·

Wear protective gloves. Sharp areas on the parts may injure your hands.



NOTICE:

Always use E10 "TORX" socket wrench when removing the front seat.


PROCEDURE

Hide 71511S 1.INSTALL SEPARATE TYPE FRONT SEAT CUSHION PAD

a.

Temporarily install the separate type front seat cushion cover.


b.

for Type A:

i.
B448799C04
2,4.396 1.75,4.146 false 0.583,3.146 0.417,3 false 0.271,2.906 0.583,3.063 0.313,0.156 10 false *1 1.958,4.396 2.271,4.552 0.313,0.156 10 false *a
*1 Hog Ring
*a Hog Ring Pliers


Using hog ring pliers, install 17 new hog rings.

NOTICE:
·

Be careful not to damage the separate type front seat cushion cover.

·

When installing the hog rings, take care to minimize wrinkles as much as possible.

·

Align the center of the hog ring installation area of the separate type front seat cushion cover with the center of the separate type front seat cushion pad so that no wrinkles appear, and securely tighten the hog rings as shown in the illustration.





c.

for Type B:

i.
B448800C04
0.594,3.146 0.417,3 false 2,4.417 1.75,4.146 false 0.271,2.906 0.583,3.063 0.313,0.156 10 false *1 1.948,4.417 2.26,4.573 0.313,0.156 10 false *a
*1 Hog Ring
*a Hog Ring Pliers


Using hog ring pliers, install 21 new hog rings.

NOTICE:
·

Be careful not to damage the separate type front seat cushion cover.

·

When installing the hog rings, take care to minimize wrinkles as much as possible.

·

Align the center of the hog ring installation area of the separate type front seat cushion cover with the center of the separate type front seat cushion pad so that no wrinkles appear, and securely tighten the hog rings as shown in the illustration.





d.
B359989C04
0.823,3.063 0.958,3.177 true 1.865,3.969 1.76,4.177 false 0.979,3.198 1.292,3.396 0.313,0.198 10 false *1 1.667,4.208 1.979,4.406 0.313,0.198 10 false *a
*1 Hog Ring
*a Hog Ring Pliers


Using hog ring pliers, install the separate type front seat cushion cover to the separate type front seat cushion pad with 2 new hog rings.

NOTICE:
·

Be careful not to damage the separate type front seat cushion cover.

·

When installing the hog rings, take care to minimize wrinkles as much as possible.

·

Securely tighten the hog rings as shown in the illustration.




Hide 2.INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER WITH PAD

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY>REASSEMBLY


Hide 71861 3.INSTALL FRONT SEAT CUSHION INNER SHIELD

Hide 71812D 4.INSTALL FRONT SEAT CUSHION SHIELD

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY>REASSEMBLY


Hide 72526A 5.INSTALL RECLINING ADJUSTER RELEASE HANDLE

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY>REASSEMBLY


Hide 73230 6.INSTALL FRONT SEAT INNER BELT ASSEMBLY

Hide 7.INSTALL FRONT SEAT ASSEMBLY

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY>INSTALLATION


Hide 72137 8.INSTALL OUTER SEAT TRACK BRACKET COVER

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY>INSTALLATION


Hide 9.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION