Home › Suspension › REAR SUSPENSION › REAR COIL SPRING › from 2017.10
RM30M0E _53 Suspension _017096 REAR SUSPENSION _0090104 REAR COIL SPRING A

REAR SUSPENSION  REAR COIL SPRING  INSTALLATION  


PROCEDURE

Hide 48231B 1.INSTALL REAR COIL SPRING LH

a.

Support the spring seat of the rear axle beam assembly using an engine lifter and 2 wooden blocks.


b.

Remove the 2 bolts and separate the rear axle beam assembly from the rear shock absorber assemblies LH and RH.


c.

Slowly lower the rear axle beam assembly using engine lifter and 2 wooden blocks.


d.

Install the rear lower coil spring insulator LH to the rear axle beam assembly.


e.
C231456C02
3.146,1.469 3.344,1.667 0.198,0.198 10 false *a
*a 10 mm (0.394 in.) or less


Install the rear upper coil spring insulator LH to the rear coil spring LH.

NOTICE:

Install the rear upper coil spring insulator LH so that the distance between the stopper and the upper end of the rear coil spring LH is 10 mm (0.394 in.) or less.



f.
C282506C01
2.146,1.188 2.698,1.323 true 2.042,1.198 2.365,1.823 true 1.938,4.01 2.615,3.406 true 2.729,1.26 2.938,1.417 0.208,0.156 10 false *a 2.417,1.771 2.625,1.917 0.208,0.146 10 false *b 2.667,3.313 2.875,3.5 0.208,0.188 10 false *c
*a Lower End of Rear Coil Spring
*b Convex Portion
*c Identification Mark


Install the rear coil spring LH to the rear axle beam assembly.

NOTICE:
·

Install the rear coil spring LH so that the distance between the lower end of the rear coil spring LH and spring stopper is within the range of the convex portion.

·

Install the rear coil spring so that the identification mark is positioned as shown in the illustration.




g.

Slowly jack up the rear axle beam assembly using engine lifter and 2 wooden blocks, and temporarily tighten the rear axle beam assembly to the rear shock absorber assemblies LH and RH with the 2 bolts.


Hide 48231A 2.INSTALL REAR COIL SPRING RH

HINT:

Use the same procedure described for the LH side.


Hide 58251D 3.INSTALL FRONT FLOOR PANEL BRACE LH

a.

Install the front floor panel brace LH to the body with the 3 bolts.

Torque:
30.1 N*m (307 kgf*cm, 22 ft.*lbf)


Hide 58251D 4.INSTALL FRONT FLOOR PANEL BRACE RH

HINT:

Use the same procedure described for the LH side.


Hide 46430 5.INSTALL NO. 3 PARKING BRAKE CABLE ASSEMBLY

a.

Install the No. 3 parking brake cable assembly with the nut.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)


Hide 46420 6.INSTALL NO. 2 PARKING BRAKE CABLE ASSEMBLY

HINT:

Use the same procedure described for the No. 3 parking brake cable assembly.


Hide 47319F 7.INSTALL REAR FLEXIBLE HOSE LH

a.

Install the rear No. 4 brake tube with the nut.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


b.

Install the rear flexible hose LH to the rear axle beam assembly with a new clip.

NOTICE:

Make sure the clip is completely pushed in.



c.

Using a 10 mm union nut wrench, install the rear No. 4 brake tube while holding the rear flexible hose LH with a wrench.

Torque:
15.2 N*m (155 kgf*cm, 11 ft.*lbf)

NOTICE:
·

Do not kink or damage the brake line.

·

Do not allow any foreign matter, such as dirt or dust to enter the brake line.

·

Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION




Hide 47318F 8.INSTALL REAR FLEXIBLE HOSE RH

HINT:

Use the same procedure described for the LH side.


Hide 89516D 9.INSTALL SKID CONTROL SENSOR WIRE LH

a.

Install the skid control sensor wire LH to the rear axle beam assembly with the nut.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)


b.

Connect the skid control sensor wire connector.


Hide 89516C 10.INSTALL SKID CONTROL SENSOR WIRE RH

HINT:

Use the same procedure described for the LH side.


Hide 12.INSTALL REAR WHEELS

Torque:
103 N*m (1050 kgf*cm, 76 ft.*lbf)

Hide 42110F 14.TIGHTEN REAR AXLE BEAM ASSEMBLY

a.

Tighten the 2 bolts.

Torque:
70 N*m (714 kgf*cm, 52 ft.*lbf)


Hide 48540 15.FULLY TIGHTEN REAR SHOCK ABSORBER ASSEMBLY LH

Hide 48530 16.FULLY TIGHTEN REAR SHOCK ABSORBER ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.