47201
1.INSTALL BRAKE MASTER CYLINDER SUB-ASSEMBLY (w/ ABS)
Install a new O-ring to the brake master cylinder sub-assembly.
Install the brake master cylinder sub-assembly to the brake booster assembly with the 2 nuts.
| *a | Torque Wrench Fulcrum Length |
Using a 10 mm union nut wrench, connect the 2 brake tubes to the brake master cylinder sub-assembly.
Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)): 13.4 N*m (137 kgf*cm, 10 ft.*lbf)
Connect the brake fluid level warning switch connector.
Engage the wire harness clamp.
| *a | Torque Wrench Fulcrum Length |
Using a 10 mm union nut wrench, connect the 6 brake tubes to the brake actuator assembly.
Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)): 13.4 N*m (137 kgf*cm, 10 ft.*lbf)
| *a | Torque Wrench Fulcrum Length |
Using a 10 mm union nut wrench, connect the 2 brake tubes to the front No. 1 brake tube way.
Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)): 13.4 N*m (137 kgf*cm, 10 ft.*lbf)
47201
2.INSTALL BRAKE MASTER CYLINDER SUB-ASSEMBLY (w/ VSC)
Install a new O-ring to the brake master cylinder sub-assembly.
Install the brake master cylinder sub-assembly to the brake booster assembly with the 2 nuts.
| *a | Torque Wrench Fulcrum Length |
Using a 12 mm union nut wrench, connect the 2 brake tubes to the brake master cylinder sub-assembly.
Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When using a union nut wrench (fulcrum length of 20 mm (0.787 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)) (B): 17.4 N*m (177 kgf*cm, 13 ft.*lbf)
Connect the brake fluid level warning switch connector.
Engage the wire harness clamp.
| *a | Torque Wrench Fulcrum Length |
Using a 10 mm and 12 mm union nut wrench, connect the 6 brake tubes to the brake actuator assembly.
Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)) (A): 13.4 N*m (137 kgf*cm, 10 ft.*lbf)
When using a union nut wrench (fulcrum length of 20 mm (0.787 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)) (B): 17.4 N*m (177 kgf*cm, 13 ft.*lbf)
| *a | Torque Wrench Fulcrum Length |
Using a 10 mm union nut wrench, connect the 2 brake tubes to the front No. 1 brake tube way.
Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)): 13.4 N*m (137 kgf*cm, 10 ft.*lbf)
31434C
3.INSTALL CLUTCH RESERVOIR TUBE (for Manual Transaxle)
Connect the clutch reservoir tube to the brake master cylinder sub-assembly with the hose clip.
74410
4.INSTALL BATTERY CARRIER ASSEMBLY
74431
5.INSTALL BATTERY TRAY
28800
6.INSTALL BATTERY
7.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
8.BLEED BRAKE LINE
9.BLEED CLUTCH LINE (for Manual Transaxle)
for C50:
for C54: