Home › Engine / Hybrid System › 1NR-FE ENGINE MECHANICAL › ENGINE ASSEMBLY(for CVT) › 2017.10–2018.01
RM30M0E _51 Engine / Hybrid System _053932 1NR-FE ENGINE MECHANICAL _0262365 ENGINE ASSEMBLY(for CVT) A

1NR-FE ENGINE MECHANICAL  ENGINE ASSEMBLY(for CVT)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:

Perform "Inspection After Repair" after replacing the engine assembly.

Click hereEngine / Hybrid System>1NR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION


PROCEDURE

Hide 12372A 1.INSTALL ENGINE MOUNTING INSULATOR LH

HINT:

Only perform this procedure when replacement of the engine mounting insulator LH is necessary.


a.
A382175C01
2.385,0.969 3.104,1.271 0.719,0.302 10 true 1 (*a), 6 0.792,0.583 1.385,0.802 0.594,0.219 10 true 2 (*a), 7 1.406,1.781 1.563,1.979 0.156,0.198 10 true 3 1.354,1.354 1.51,1.552 0.156,0.198 10 true 4 2.219,1.646 2.375,1.844 0.156,0.198 10 true 5
*a Temporarily Tighten


Engage the hook and temporarily install the engine mounting insulator LH to the vehicle.


b.

Install the 5 bolts in the order shown in the illustration.

Torque:
52 N*m (530 kgf*cm, 38 ft.*lbf)


Hide 12305 2.INSTALL ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH

HINT:

Only perform this procedure when replacement of the engine mounting insulator sub-assembly RH is necessary.


a.
A382174C01
2.146,0.469 2.792,0.698 0.646,0.229 10 true 1 (*a), 4 0.958,1.885 1.115,2.083 0.156,0.198 10 true 2 1.573,0.573 1.729,0.771 0.156,0.198 10 true 3
*a Temporarily Tighten


Engage the hook and temporarily install the engine mounting insulator sub-assembly RH to the vehicle.


b.

Install the 3 bolts in the order shown in the illustration.

Torque:
52 N*m (530 kgf*cm, 38 ft.*lbf)


Hide 3.REMOVE ENGINE STAND

a.

Using a chain block and sling device, secure the engine assembly.

NOTICE:

Make sure that the sling angle is correct to prevent the engine assembly and engine hangers from being damaged or deformed.



b.

Remove the engine stand from the engine.


Hide 32101B 4.INSTALL DRIVE PLATE AND RING GEAR SUB-ASSEMBLY

a.

Using height adjustable attachments and plate lift attachments, place the engine assembly on a flat, level surface.

NOTICE:
·

Using height adjustable attachments and plate lift attachments, place the engine assembly horizontally.

·

Using an engine sling device and engine lifter, secure the engine assembly before servicing.




b.
A305670E01
2.146,1.99 2.385,1.75 true 2.458,1.677 2.844,1.844 0.385,0.167 10 false SST

Using SST, hold the crankshaft pulley.

SST
09960-10010  (09962-01000, 09963-01000)


c.
A382921C01
0.865,0.958 1.198,0.958 false 2.125,1.979 1.708,1.979 false 2.677,1.49 2.177,1.24 false 0.688,0.865 1,1.021 0.313,0.156 10 false *1 2.167,1.917 2.479,2.073 0.313,0.156 10 false *2 2.708,1.427 3.021,1.583 0.313,0.156 10 false *3
*1 Front Drive Plate Spacer (Reversible)
*2 Drive Plate and Ring Gear Sub-assembly
*3 Rear Drive Plate Spacer
V100135

Engine Side
V100136

Transaxle Side


Install the front drive plate spacer, drive plate and ring gear sub-assembly and rear drive plate spacer to the crankshaft.

NOTICE:

As the drive plate and ring gear sub-assembly and rear drive plate spacer are not reversible, be sure to install them so that they are facing in the direction as shown in the illustration.


HINT:

The front drive plate spacer is reversible.



d.

Clean the 8 bolts and their holes.


e.
A192239C40
1.781,0.552 1.542,1.385 false 1.823,0.458 2,0.615 0.177,0.156 10 false *a
*a Adhesive


Apply adhesive to 2 or 3 threads at the end of each of the 8 bolts.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent


NOTICE:

To prevent contamination by foreign matter, install immediately after applying adhesive.



f.
A382920C01
1.646,0.448 1.802,0.646 0.156,0.198 10 true 1 1.646,1.75 1.802,1.948 0.156,0.198 10 true 2 0.99,1.115 1.146,1.313 0.156,0.198 10 true 3 2.271,1.146 2.458,1.323 0.188,0.177 10 true 4 1.146,0.646 1.302,0.844 0.156,0.198 10 true 5 2.146,1.583 2.302,1.781 0.156,0.198 10 true 6 1.219,1.635 1.375,1.833 0.156,0.198 10 true 7 2.125,0.74 2.281,0.938 0.156,0.198 10 true 8

Install and uniformly tighten the 8 bolts in several steps, in the sequence shown in the illustration.

Torque:
88 N*m (897 kgf*cm, 65 ft.*lbf)

NOTICE:

Do not start the engine for at least 1 hour after installing the drive plate and ring gear sub-assembly.



Hide 30400 5.INSTALL CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY

a.
C288568C01
0.969,0.625 0.51,0.406 false 2.938,0.344 1.635,0.865 true 0.354,0.313 0.667,0.469 0.313,0.156 10 false *1 2.969,0.25 3.281,0.406 0.313,0.156 10 false *2
*1 Crankshaft
*2 Torque Converter Assembly Centerpiece
V100135

Clutch Spline Grease


Apply clutch spline grease to the surface of the crankshaft that contacts the torque converter assembly centerpiece.

Grease:

Toyota Genuine Clutch Spline Grease or equivalent


Maximum grease amount:

Approximately 1 g (0.0353 oz.)



b.
C288098C01
0.573,0.375 1.198,0.375 true 2.635,1.021 2.917,1.021 true 0.417,0.292 0.729,0.448 0.313,0.156 10 false *1 2.958,0.927 3.271,1.083 0.313,0.156 10 false *1
*1 Knock Pin


Confirm that the 2 knock pins are installed on the engine assembly and are not damaged.


c.
C231548N02
1.396,0.375 1.552,0.573 0.156,0.198 10 false A 2.667,0.531 2.823,0.729 0.156,0.198 10 false A 2.99,1.26 3.146,1.458 0.156,0.198 10 false A 3.052,1.854 3.208,2.052 0.156,0.198 10 true A 2.729,2.427 2.885,2.625 0.156,0.198 10 false B 2.385,2.708 2.542,2.906 0.156,0.198 10 false B 1.75,2.813 1.906,3.01 0.156,0.198 10 false B 1.208,2.677 1.365,2.875 0.156,0.198 10 true B

Install the continuously variable transaxle assembly to the engine assembly with the 8 bolts.

Torque:
Bolt A : 64 N*m (653 kgf*cm, 47 ft.*lbf)
Bolt B : 39 N*m (398 kgf*cm, 29 ft.*lbf)

NOTICE:
·

Make sure that the wire harness or similar items are not pinched between the contact surfaces.

·

Do not forcibly pry on the continuously variable transaxle assembly.

·

When mounting the continuously variable transaxle assembly to the engine assembly, make sure to securely fit the knock pins into the knock holes.

·

Check that the torque converter assembly rotates.

·

When tightening the bolts, be sure that the mating surfaces of the engine assembly and continuously variable transaxle assembly are in close contact with one another.



HINT:

Bolt length:

·

Bolt A: 45 mm (1.77 in.)

·

Bolt B: 35 mm (1.38 in.)




Hide 87245 6.INSTALL INLET HEATER WATER HOSE

A382716C02
0.844,0.51 0.594,0.292 false 0.208,0.125 0.521,0.281 0.313,0.156 10 false *a 0.448,0.198 0.76,0.354 0.313,0.156 10 false *b 0.74,0.052 1.052,0.208 0.313,0.156 10 false *c 1.667,3.198 1.823,3.396 0.156,0.198 10 false A
*a View A
*b Paint Mark
*c Top of Vehicle


a.

Engage the clamp to connect the hose clamp to the wire harness clamp bracket.


b.

Connect the inlet heater water hose to the cylinder head sub-assembly and slide the hose clip to secure it.

NOTICE:

Perform the installation with the inlet heater water hose and hose clip at the correct angle.



Hide 16260 7.CONNECT WATER BY-PASS HOSE ASSEMBLY

a.
A382717C02
0.583,0.719 0.396,0.938 false 0.208,0.125 0.521,0.281 0.313,0.156 10 false *a 0.188,0.969 0.5,1.125 0.313,0.156 10 false *b 0.135,0.625 0.448,0.781 0.313,0.156 10 false *c 1.979,2.708 2.135,2.906 0.156,0.198 10 true A
*a View A
*b Paint Mark
*c Front of Vehicle


Connect the water by-pass hose assembly to the No. 1 water by-pass pipe sub-assembly and slide the hose clip to secure it.

NOTICE:

Perform the installation with the water by-pass hose assembly and hose clip at the correct angle.



Hide 82121 8.INSTALL ENGINE WIRE

a.

Connect all the engine wire connectors.


b.

Connect the engine wire to the continuously variable transaxle assembly with the bolt.

Torque:
12.8 N*m (131 kgf*cm, 9 ft.*lbf)


c.

Connect the engine wire to the cylinder head cover sub-assembly with the 2 nuts.

Torque:
8.4 N*m (86 kgf*cm, 74 in.*lbf)


d.

Connect the engine wire to the cylinder head sub-assembly with the 2 bolts.

Torque:
8.4 N*m (86 kgf*cm, 74 in.*lbf)


Hide 51201 9.TEMPORARILY TIGHTEN FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY

a.

Temporarily tighten the front suspension crossmember sub-assembly to the No. 2 engine moving control rod with the through bolt.


Hide 10.REMOVE ENGINE HANGER

a.

Remove the 2 bolts, No. 1 engine hanger and No. 2 engine hanger from the cylinder head sub-assembly.


Hide 32101G 11.INSTALL DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT

Hide 11363A 12.INSTALL FLYWHEEL HOUSING SIDE COVER

Hide 28100 13.INSTALL STARTER ASSEMBLY

Hide 14.INSTALL ENGINE ASSEMBLY WITH CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY

a.

Place height adjustment or plate lift attachments on an engine lifter, and then set the engine assembly with continuously variable transaxle assembly.

NOTICE:
·

Place the height adjustment or plate lift attachments so that the engine assembly with continuously variable transaxle assembly is level.

·

As the engine assembly with continuously variable transaxle assembly is very heavy, be sure to support it securely.

·

To prevent deformation of the continuously variable transaxle oil pan sub-assembly, never set any attachments against the oil pan sub-assembly of the continuously variable transaxle assembly.




b.

Operate the engine lifter and lift the engine assembly with transaxle and front suspension crossmember sub-assembly to the position where the engine mounting insulator sub-assembly RH and engine mounting insulator LH can be installed.

CAUTION:

Do not raise the engine more than necessary. If the engine is raised excessively, the vehicle may also be lifted up.


NOTICE:

Make sure that the engine is clear of all wiring and hoses.



c.

Connect the engine mounting insulator LH to the engine mounting bracket LH with the through bolt and nut.

Torque:
52 N*m (530 kgf*cm, 38 ft.*lbf)

HINT:

Tighten by holding the nut and turning the bolt.



d.

Connect the engine mounting insulator sub-assembly RH to the engine mounting bracket RH with the bolt and 2 nuts.

Torque:
52 N*m (530 kgf*cm, 38 ft.*lbf)


e.

Temporarily install the front suspension crossmember sub-assembly to the body with the 6 bolts.


f.

By inserting SST into the datum holes in the front suspension crossmember RH and LH alternately, tighten bolts A, B and C on both sides to the specified torque, in several steps.

C233133C02
4.458,1.5 4.573,1.302 true 4.094,2.635 4.719,2.635 true 2.781,1.5 2.698,1.292 true 3.135,2.635 2.51,2.635 true 4.313,1.479 4.469,1.625 0.156,0.146 10 false *a 2.802,1.479 2.958,1.625 0.156,0.146 10 false *a 5.563,2.052 5.688,2.198 0.125,0.146 10 false A 5.333,2.458 5.458,2.604 0.125,0.146 10 false B 5.365,2.656 5.49,2.802 0.125,0.146 10 false C 1.51,1.979 1.635,2.125 0.125,0.146 10 false A 1.771,2.427 1.896,2.573 0.125,0.146 10 false B 3.802,2.573 4.104,2.719 0.302,0.146 10 false SST 3.156,2.573 3.458,2.719 0.302,0.146 10 false SST 5.76,3.521 5.99,3.667 0.229,0.146 10 false *c 5.021,3.521 5.25,3.667 0.229,0.146 10 false *b 2.469,3.521 2.698,3.667 0.229,0.146 10 false *c 1.729,3.521 1.958,3.667 0.229,0.146 10 false *b 1.771,2.635 1.896,2.781 0.125,0.146 10 false C
*a Datum Hole *b Correct
*c Incorrect - -
V100135

Front of Vehicle - -


SST
09670-00011  

Torque:
Bolt A : 70 N*m (714 kgf*cm, 52 ft.*lbf)
Bolt B : 165 N*m (1683 kgf*cm, 122 ft.*lbf)
Bolt C : 95 N*m (969 kgf*cm, 70 ft.*lbf)

NOTICE:
·

Insert SST into the datum hole vertically.

·

If impossible to insert SST vertically, loosen all bolts and then insert SST again.




g.

Tighten the engine moving control rod bolt.

Torque:
120 N*m (1224 kgf*cm, 89 ft.*lbf)


Hide 15.INSTALL WIRE HARNESS CLAMP BRACKET

a.

Install the wire harness clamp bracket to the continuously variable transaxle assembly with the bolt.

Torque:
for TMMIN Made : 29 N*m (296 kgf*cm, 21 ft.*lbf)
for TMT Made : 30 N*m (306 kgf*cm, 22 ft.*lbf)


Hide 12144 16.INSTALL OIL PAN COVER SILENCER (w/ Metal Type Under Cover)

HINT:

Perform this procedure only when replacement of the oil pan cover silencer is necessary.


a.
A380371C01
2.198,1.177 2.583,1.333 false 2.646,1.271 2.958,1.469 0.313,0.198 10 false *a
*a Align RH Edge


Align the RH edge of the oil pan cover silencer with the oil pan protector and attach it as shown in the illustration.


Hide 12137 17.INSTALL OIL PAN PROTECTOR (w/ Metal Type Under Cover)

a.

Install the oil pan protector to the oil pan sub-assembly with the 3 bolts.

Torque:
23.5 N*m (240 kgf*cm, 17 ft.*lbf)


Hide 43498A 18.INSTALL NO. 1 DRIVE SHAFT HEAT INSULATOR

A384958C01
0.646,0.99 0.802,1.188 0.156,0.198 10 true 1 1.458,0.208 1.615,0.406 0.156,0.198 10 true 2

a.

Temporarily tighten the No. 1 drive shaft heat insulator to the oil pan sub-assembly with the 2 bolts.


b.

Fully tighten the 2 bolts, in the sequence shown in the illustration.

Torque:
23.5 N*m (240 kgf*cm, 17 ft.*lbf)


Hide 45025D 19.INSTALL NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY

Hide 45209 20.CONNECT STEERING SLIDING YOKE SUB-ASSEMBLY

Hide 45259A 21.INSTALL COLUMN HOLE COVER SILENCER SHEET

Hide 33820B 23.CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

Hide 17410 24.INSTALL FRONT EXHAUST PIPE ASSEMBLY

Hide 57533B 25.INSTALL FRONT FLOOR CENTER BRACE (for TMT Made)

Hide 57533B 26.INSTALL FRONT FLOOR CENTER BRACE (for TMMIN Made)

Hide 82121 27.CONNECT ENGINE WIRE (for LHD)

a.
A313900C02
3.052,0.948 3.323,1.146 0.271,0.198 10 false 45° 2.417,0.958 2.688,1.156 0.271,0.198 10 false 45° 2.75,0.917 3.063,1.115 0.313,0.198 10 false *a
*a Top of the Vehicle


Pass the engine wire through the hole to the outside of the engine room and engage the grommet to the vehicle as shown in the illustration.


b.

Engage the clamp to connect the engine wire to the wire harness clamp bracket.


c.
A382534

Engage the 2 clamps to connect the engine wire to the wire harness clamp bracket and vehicle.


d.

Connect the 4 connectors as shown in the illustration.


e.

Engage the 2 claws to connect the engine wire to the engine room relay block.


f.

Install the nut to the engine room relay block.

Torque:
8.4 N*m (86 kgf*cm, 74 in.*lbf)


g.

Connect the connector to the engine room relay block.


h.

Engage the clamp to connect the engine wire to the vehicle.


i.

Connect the engine wire to the vehicle with the bolt.

Torque:
8.4 N*m (86 kgf*cm, 74 in.*lbf)


j.

Install the relay block cover to the engine room relay block.


Hide 82121 28.CONNECT ENGINE WIRE (for RHD)

a.
A112923C01
0.51,0.146 0.823,0.302 0.313,0.156 10 false *a 0.781,0.198 1.031,0.385 0.25,0.188 10 false 45° 0.25,0.198 0.5,0.385 0.25,0.188 10 false 45°
*a Top of the Vehicle


Pass the engine wire through the hole to the outside of the engine room and engage the grommet to the vehicle as shown in the illustration.


b.
A381360

Engage the 2 clamps to connect the engine wire to the wire harness clamp bracket and vehicle.


c.

Connect the 3 connectors as shown in the illustration.


d.

Engage the 2 claws to connect the engine wire to the engine room relay block.


e.

Install the nut to the engine room relay block.

Torque:
8.4 N*m (86 kgf*cm, 74 in.*lbf)


f.

Connect the connector to the engine room relay block.


g.

Engage the clamp to connect the engine wire to the vehicle.


h.

Connect the engine wire to the vehicle with the bolt.

Torque:
8.4 N*m (86 kgf*cm, 74 in.*lbf)


i.

Install the relay block cover to the engine room relay block.


Hide 55550 29.INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY

Hide 88320 30.INSTALL COOLER COMPRESSOR ASSEMBLY (w/ Cooler System)

a.
A381266C01
0.906,0.729 1.063,0.927 0.156,0.198 10 true 1 2.365,0.302 2.521,0.5 0.156,0.198 10 true 3 2.406,1.698 2.563,1.896 0.156,0.198 10 true 4 1.052,1.865 1.208,2.063 0.156,0.198 10 true 2

Install the cooler compressor assembly to the cylinder block sub-assembly and oil pan sub-assembly with the 4 bolts, in the sequence shown in the illustration.

Torque:
24.5 N*m (250 kgf*cm, 18 ft.*lbf)


b.

Connect the cooler compressor assembly connector.


Hide 23901 31.CONNECT FUEL TUBE SUB-ASSEMBLY

Hide 23841B 32.INSTALL EFI FUEL PIPE CLAMP

Hide 87245 33.CONNECT INLET HEATER WATER HOSE

a.
A382715C01
2.563,0.563 2.354,0.375 false 1.979,0.156 2.292,0.313 0.313,0.156 10 false *a 2.167,0.281 2.479,0.438 0.313,0.156 10 false *b 2.469,0.115 2.781,0.271 0.313,0.156 10 false *c 1.208,2.854 1.365,3.052 0.156,0.198 10 false A
*a View A
*b Paint Mark
*c Top of Vehicle


Connect the inlet heater water hose to the heater radiator assembly and slide the hose clip to secure it.

NOTICE:

Perform the installation with the inlet heater water hose and hose clip at the correct angle.



Hide 87246 34.CONNECT OUTLET HEATER WATER HOSE

A382714C01
0.823,0.521 0.594,0.302 false 0.188,0.094 0.5,0.25 0.313,0.156 10 false *a 0.427,0.229 0.74,0.385 0.313,0.156 10 false *b 0.74,0.063 1.052,0.219 0.313,0.156 10 false *c 2,2.531 2.156,2.729 0.156,0.198 10 true A
*a View A
*b Paint Mark
*c Top of Vehicle


a.

Connect the outlet heater water hose to the heater radiator assembly and slide the hose clip to secure it.

NOTICE:

Perform the installation with the outlet heater water hose and hose clip at the correct angle.



Hide 16572D 35.CONNECT NO. 2 RADIATOR HOSE

a.
A382168C01
1.51,2.26 1.646,2.49 true 1.031,2.125 1.344,2.281 0.313,0.156 10 false *a 1.354,2.188 1.667,2.344 0.313,0.156 10 false *b 1.573,2.083 1.885,2.24 0.313,0.156 10 false *c 2.323,1.427 2.479,1.625 0.156,0.198 10 false A
*a View A
*b Paint Mark
*c Top of Vehicle


Connect the No. 2 radiator hose to the water inlet and slide the hose clip to secure it.

NOTICE:

Perform the installation with the No. 2 radiator hose and hose clip at the correct angle.



Hide 16571C 36.CONNECT NO. 1 RADIATOR HOSE

a.
A382713C01
0.542,0.438 0.76,0.552 false 0.177,0.177 0.49,0.333 0.313,0.156 10 false *a 0.365,0.333 0.677,0.49 0.313,0.156 10 false *b 0.667,0.135 0.979,0.292 0.313,0.156 10 false *c 2.76,1.958 2.917,2.156 0.156,0.198 10 true A
*a View A
*b Paint Mark
*c Top of Vehicle


Connect the No. 1 radiator hose to the cylinder head sub-assembly and slide the hose clip to secure it.

NOTICE:

Perform the installation with the No. 1 radiator hose and hose clip at the correct angle.



Hide 35141F 37.CONNECT NO. 1 BREATHER PLUG

a.

Engage the clamp to connect the No. 1 breather plug to the hose clamp.


Hide 17341T 38.CONNECT NO. 1 AIR HOSE

a.

Engage the clamp to connect the No. 1 air hose to the intake manifold.


Hide 25860D 39.INSTALL VACUUM SWITCHING VALVE ASSEMBLY

a.

Install the vacuum switching valve assembly to the intake manifold with the bolt.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


b.

Connect the vacuum switching valve assembly connector.


Hide 44774 40.CONNECT UNION TO CONNECTOR TUBE HOSE

a.

Connect the union to connector tube hose to the intake manifold and slide the hose clip to secure it.


Hide 27020 41.INSTALL GENERATOR WITH REGULATOR ASSEMBLY

Hide 42.INSTALL WIRE HARNESS CLAMP BRACKET

Hide 17167 44.INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

Hide 11452 45.INSTALL OIL LEVEL DIPSTICK GUIDE

Hide 15301 46.INSTALL OIL LEVEL DIPSTICK SUB-ASSEMBLY

Hide 16361A 47.INSTALL FAN AND GENERATOR V BELT

Hide 74410 48.INSTALL BATTERY CARRIER ASSEMBLY

a.

Install the battery carrier assembly to the engine mounting insulator LH and vehicle with the 5 bolts.

Torque:
17.2 N*m (175 kgf*cm, 13 ft.*lbf)


b.

Engage the 4 clamps to connect the wire harness to the battery carrier assembly.


Hide 74431 49.INSTALL BATTERY TRAY

a.

Install the battery tray to the battery carrier assembly.


Hide 28800 50.INSTALL BATTERY

a.
A314466C02
0.406,0.177 0.531,0.292 true 0.698,0.438 0.844,0.219 true 0.917,1.365 1.021,1.417 false 0.74,1.49 0.865,1.646 true 1.063,1.354 1.375,1.51 0.313,0.156 10 false *1 0.885,1.625 1.083,1.792 0.198,0.167 10 true *2 0.25,0.083 0.563,0.24 0.313,0.156 10 false *3 0.865,0.156 1.073,0.313 0.208,0.156 10 false *4
*1 Battery Clamp Bolt
*2 Battery Carrier
*3 Engine Room Main Wire
*4 Engine Wire


Install the battery to the battery tray.


b.

Install the battery clamp sub-assembly to the battery carrier assembly with the 2 nuts and battery clamp bolt.

Torque:
3.5 N*m (36 kgf*cm, 31 in.*lbf)

HINT:

Engage the hook of the battery clamp bolt to the notch of the battery carrier.



c.

Engage the 2 claws to connect the engine room main wire to the engine wire.


d.

Connect the engine room main wire with engine wire to the positive (+) battery terminal with the nut.

Torque:
7.6 N*m (77 kgf*cm, 67 in.*lbf)


e.

Install the terminal cover to the positive (+) battery terminal.


Hide 17701 51.INSTALL AIR CLEANER CASE SUB-ASSEMBLY

a.

Install the air cleaner case sub-assembly to the air cleaner bracket with the 3 bolts.

Torque:
7.8 N*m (80 kgf*cm, 69 in.*lbf)


b.

Engage the clamp to install the engine wire to the air cleaner case sub-assembly.


Hide 17801 52.INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

a.

Install the air cleaner filter element sub-assembly to the air cleaner case sub-assembly.


Hide 53.INSTALL AIR CLEANER CAP SUB-ASSEMBLY

a.

Engage the 2 guides to install the air cleaner cap sub-assembly to the air cleaner case sub-assembly.


b.

Engage the 2 clamps of the air cleaner cap sub-assembly.


c.

Engage the 2 clamps to install the engine wire to the air cleaner cap sub-assembly.


d.

Connect the mass air flow meter connector.


Hide 17880 54.INSTALL AIR CLEANER HOSE ASSEMBLY

Hide 12262 55.CONNECT NO. 2 VENTILATION HOSE

Hide 23827A 57.CONNECT NO. 2 FUEL VAPOR FEED HOSE

a.
A385250C02
2.01,0.854 2.365,0.74 false 1.927,0.292 2.24,0.448 0.313,0.156 10 false *a 1.813,0.792 2.125,0.948 0.313,0.156 10 false *b 2.292,0.177 2.604,0.333 0.313,0.156 10 false *c 2.448,0.438 2.906,0.635 0.458,0.198 10 false 30° 2.125,0.438 2.583,0.635 0.458,0.198 10 false 30° 1.438,0.99 1.594,1.188 0.156,0.198 10 true A
*a View A
*b Hose Paint Mark
*c Top of Vehicle


Connect the No. 2 fuel vapor feed hose to the purge VSV (purge valve).

NOTICE:

Perform the installation with the No. 2 fuel vapor feed hose at the correct angle.



Hide 23826 58.CONNECT NO. 1 FUEL VAPOR FEED HOSE

a.
A388034C01
2.385,1.521 2.469,1.094 true 1.854,0.5 2.167,0.656 0.313,0.156 10 false *a 2.313,1.552 2.625,1.708 0.313,0.156 10 false *b 2.833,0.958 3.146,1.115 0.313,0.156 10 false *c 2.229,0.365 2.542,0.521 0.313,0.156 10 false *d 0.542,1.271 0.698,1.469 0.156,0.198 10 false A 2.594,0.833 3.052,1.031 0.458,0.198 10 false 30° 2.594,1.115 3.052,1.313 0.458,0.198 10 false 30°
*a View A
*b Hose Paint Mark
*c Rear Side of Vehicle
*d Top of Vehicle


Connect the No. 1 fuel vapor feed hose to the purge VSV (purge valve) and slide the hose clip to secure it.

NOTICE:

Perform the installation with the No. 1 fuel vapor feed hose at the correct angle.



Hide 59.INSTALL FRONT WHEELS

Torque:
103 N*m (1050 kgf*cm, 76 ft.*lbf)

Hide 60.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 61.ADJUST SHIFT LEVER POSITION

Hide 64.ADD CONTINUOUSLY VARIABLE TRANSAXLE FLUID

Hide 69.INSPECT RESERVOIR TANK COOLANT LEVEL

Hide 70.INSPECT FOR CONTINUOUSLY VARIABLE TRANSAXLE FLUID LEAK

Hide 71.INSPECT FOR EXHAUST GAS LEAK

HINT:

Perform "Inspection After Repairs" after repairing gas leaks in the exhaust system.

Click hereEngine / Hybrid System>1NR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION


Hide 75.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT

Hide 51441C 76.INSTALL ENGINE UNDER COVER RH (w/o Metal Type Under Cover)

Hide 51442C 77.INSTALL ENGINE UNDER COVER LH (w/o Metal Type Under Cover)

Hide 51405A 78.INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY (w/ Metal Type Under Cover)

Hide 51451A 79.INSTALL CENTER ENGINE UNDER COVER (w/ Metal Type Under Cover)