Use the same procedure for the LH side and RH side.
The following procedure is for the LH side.
42431
1.INSTALL REAR DISC
| *a | Matchmark |
Align the matchmarks on the rear disc and rear axle hub and bearing assembly, and install the rear disc.
When replacing the rear disc with a new one, select the installation position where the rear disc has minimal runout.
47822
2.INSTALL REAR DISC BRAKE CYLINDER MOUNTING
Install the rear disc brake cylinder mounting to the rear axle beam assembly with the 2 bolts.
47875R
3.INSTALL REAR DISC BRAKE BUSH DUST BOOT
|
Lithium Soap Base Glycol Grease |
Apply a light layer of lithium soap base glycol grease to the entire circumference of 2 new rear disc brake bush dust boots.
Apply at least 0.3 g (0.01 oz.) of lithium soap base glycol grease to each rear disc brake bush dust boot.
Install the 2 rear disc brake bush dust boots to the rear disc brake cylinder mounting.
47835
4.INSTALL REAR DISC BRAKE PAD GUIDE PIN
|
Lithium Soap Base Glycol Grease |
Apply a light layer of lithium soap base glycol grease to the contact surface of the 2 rear disc brake pad guide pins.
Install a new rear disc brake cylinder slide bush to each rear disc brake pad guide pin.
|
Lithium Soap Base Glycol Grease |
Apply a light layer of lithium soap base glycol grease to the sliding part and sealing surfaces of the 2 rear disc brake pad guide pins.
Install the 2 rear disc brake pad guide pins to the rear disc brake cylinder mounting.
Push the 2 rear disc brake pad guide pins into the 2 rear disc brake bush dust boots to engage the 2 rear disc brake pad guide pins to the rear disc brake bush dust boot.
04948
5.INSTALL REAR DISC BRAKE FITTING KIT
| *1 | Rear No. 1 Disc Brake Pad Support Plate |
| *2 | Rear No. 2 Disc Brake Pad Support Plate |
Install the rear No. 1 disc brake pad support plate and rear No. 2 disc brake pad support plate to the rear disc brake cylinder mounting.
Be sure to install each rear disc brake pad support plate in the correct position and direction.
04946
6.INSTALL REAR DISC BRAKE ANTI SQUEAL SHIM KIT
| *a | Inner |
| *b | Outer |
|
Disc Brake Grease |
Apply disc brake grease to the back plate of the rear disc brake pads.
| *1 | Rear No. 1 Disc Brake Anti Squeal Shim |
| *2 | Rear No. 2 Disc Brake Anti Squeal Shim |
| *3 | Rear Disc Brake Pad |
Install the rear No. 1 disc brake anti squeal shim and rear No. 2 disc brake anti squeal shim to each rear disc brake pad.
Install the anti squeal shims in the correct positions and directions.
When replacing worn pads, the anti squeal shims must be replaced together with the rear disc brake pads.
Make sure that disc brake grease is not applied onto the lining surface.
04466
7.INSTALL REAR DISC BRAKE PAD
Install the 2 rear disc brake pads to the rear disc brake cylinder mounting.
There should be no oil or grease on the friction surfaces of the rear disc brake pads or the rear disc.
47850
8.INSTALL REAR DISC BRAKE CYLINDER ASSEMBLY
To compensate for pad lining thickness, use SST to adjust the protrusion of the rear disc brake piston by turning it.
Place the disc between the 2 brake pads and determine the piston return value.
Turn the rear disc brake piston to the position where the protrusion on the rear disc brake pad lines up properly with the piston groove.
Hold each rear disc brake pad guide pin, and install the rear disc brake cylinder assembly to the rear disc brake cylinder mounting with the 2 bolts.
47319F
9.CONNECT REAR FLEXIBLE HOSE
| *a | Lock Hole |
Connect the rear flexible hose to the rear disc brake cylinder assembly with a new union bolt and a new gasket.
Install the rear flexible hose lock securely into the lock hole in the rear disc brake cylinder assembly.
46430
10.CONNECT NO. 3 PARKING BRAKE CABLE ASSEMBLY
Engage the clip to install the No. 3 parking brake cable assembly to the rear disc brake cylinder assembly.
Be sure to engage the clip to the rear disc brake cylinder assembly.
Connect the No. 3 parking brake cable assembly to the rear disc brake cylinder assembly.
11. BLEED BRAKE LINE
for LHD:
Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE FLUID(for LHD)>BLEEDING
for RHD:
Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE FLUID(for RHD)>BLEEDING
12.INSTALL REAR WHEEL
13.ADJUST PARKING BRAKE LEVER TRAVEL
58910C
14.INSTALL REAR CONSOLE BOX ASSEMBLY (for Separate Type)
58910C
15.INSTALL REAR CONSOLE BOX ASSEMBLY (for Integrated Type)