Home › Drivetrain › C54 MANUAL TRANSMISSION / TRANSAXLE › TRANSMISSION CONTROL CABLE(for 1NR-FE) › 2017.10–2018.01
RM30M0E _52 Drivetrain _017091 C54 MANUAL TRANSMISSION / TRANSAXLE _0267610 TRANSMISSION CONTROL CABLE(for 1NR-FE) A

C54 MANUAL TRANSMISSION / TRANSAXLE  TRANSMISSION CONTROL CABLE(for 1NR-FE)  REMOVAL  


PROCEDURE

Hide 12262 1.DISCONNECT NO. 2 VENTILATION HOSE

Hide 17880 2.REMOVE AIR CLEANER HOSE ASSEMBLY

Hide 17801 4.REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

Hide 58910C 9.REMOVE REAR CONSOLE BOX ASSEMBLY (for Integrated Type)

Hide 58910C 10.REMOVE REAR CONSOLE BOX ASSEMBLY (for Separate Type)

Hide 58816D 11.REMOVE NO. 1 FRONT CONSOLE BOX INSERT (for TMT Made)

Hide 58817A 12.REMOVE NO. 2 FRONT CONSOLE BOX INSERT (for TMT Made)

Hide 58911A 13.REMOVE NO. 1 SIDE BOX PANEL (for TMT Made)

Hide 58912C 14.REMOVE NO. 2 SIDE BOX PANEL (for TMT Made)

Hide 58916 15.REMOVE BOX BOTTOM MAT (for TMT Made)

Hide 58839A 16.REMOVE CONSOLE BOX HOLE COVER (for TMT Made)

Hide 58810J 17.REMOVE CONSOLE BOX ASSEMBLY (for TMT Made)

Hide 57533B 18.REMOVE FRONT FLOOR CENTER BRACE (for TMMIN Made)

Hide 57533B 19.REMOVE FRONT FLOOR CENTER BRACE (for TMT Made)

Hide 17410 20.REMOVE FRONT EXHAUST PIPE ASSEMBLY (for TMMIN Made)

Hide 17410 21.REMOVE FRONT EXHAUST PIPE ASSEMBLY (for TMT Made)

Hide 58151 22.REMOVE FRONT NO. 1 FLOOR HEAT INSULATOR

a.
C294351

Remove the 2 bolts, nut and front No. 1 floor heat insulator from the body.


Hide 33820B 23.REMOVE TRANSMISSION CONTROL CABLE ASSEMBLY

a.
C294352C01
0.594,1.25 0.802,1.063 false 1.427,3.094 1.792,2.615 true 2.365,3.156 2.656,2.708 true 1.281,3.021 1.594,3.177 0.313,0.156 10 false *1 2.219,3.094 2.531,3.25 0.313,0.156 10 false *2 0.427,1.177 0.74,1.333 0.313,0.156 10 false *3
*1 Clip A
*2 Clip B
*3 Nut
V100135

Rotate approximately 180°


Remove the clip A to disconnect the select cable end of the transmission control cable assembly from the floor shift shift lever assembly.


b.

Widen the clip B to disconnect the shift cable end of the transmission control cable assembly from the floor shift shift lever assembly.


c.

Rotate the 2 nuts of the transmission control cable assembly approximately 180° in the direction shown in the illustration, and while holding the nut, separate the transmission control cable assembly from the floor shift shift lever assembly.

NOTICE:

Do not rotate the nut excessively as it may damage the internal spring and transmission control cable assembly will not be reusable.



d.
C294354E01
0.927,1.115 1.063,1.302 0.135,0.188 10 true A 1.021,2.083 1.177,2.281 0.156,0.198 10 true A 2.292,0.375 2.448,0.552 0.156,0.177 10 true B 2.688,1.583 2.844,1.781 0.156,0.198 10 false B

Remove the 2 clips A and 2 washers to disconnect the transmission control cable assembly from the manual transaxle assembly.


e.

Remove the 2 clips B to separate the transmission control cable assembly from the No. 1 transmission control cable bracket.


f.
C294355

Remove the 3 nuts and transmission control cable assembly from the body.